AutoZone | Repair Guides | Engine Performance & Emission Controls | Components & Systems | Throttle Position Sensor | AutoZone.com

Search suggestions

    My Vehicles

    Add a Vehicle

    Find a Store

    Select Store

    SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OVER $100.

    Use Code: FALLSAVINGS

    See Details

    2007 Jeep Compass

    Throttle Position Sensor

    Print

    Operation



    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009

    The Throttle Position Sensor (TPS) is a Linear Potentiometer that monitors the throttle position. The TPS operates within a 5 volt DC reference range, and provides a linear input signal to the Powertrain Control Module (PCM). The PCM uses data from the TPS to calculate air-fuel mixture, ignition timing, fuel injector pulse width, and transmission/transaxle gear position.

    Removal & Installation



    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009

    The Throttle Position Sensor (TPS) is not serviceable as a standalone part. The TPS is an integral part of the throttle body. If the TPS requires replacement, replace the throttle body assembly. Refer to Throttle Body, removal & installation.

    Testing



    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009


    NOTE
    Refer to the Electrical Wiring Diagram for component and connector locations, connector views, and circuit-specific information.

    Connection And Wiring Diagnosis

    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009

    Refer to the Electrical Wiring Diagram for component and connector locations, connector views, and circuit-specific information.

    Many intermittent open or short circuits may be caused by wiring harness and connector movement due to vibration, engine torque, bumps and rough pavement, etc.

    1. Test the wiring harness and connectors by performing the following tests:

      Move the related connectors and wiring while monitoring the appropriate scan tool data.
       
      Move the related connectors and wiring with the component commanded ON and OFF. Using a suitable the scan tool, observe the component operation.
       
      With the engine running, move the related connectors and wiring while monitoring component operation.
       
      If harness or connector movement affects the data displayed, the component and system operation, or the engine operation, inspect and repair the harness or connections as necessary.
       

    2.  
    3. Test the connector terminal pins and/or wiring by performing the following tests:

      Inspect for incorrect mating of the connector halves, or terminals not fully seated in the connector body.
       
      Inspect for improperly formed or damaged terminals and test for incorrect terminal tension.
       
      Inspect for poor terminal to wire connections including terminals crimped over insulation. This requires removing the terminal from the connector body.
       
      Inspect for corrosion or water intrusion. Pierced or damaged insulation can allow moisture to enter the wiring. The conductor can corrode inside the insulation with little visible evidence. Look for swollen and/or brittle sections of wire in the suspect circuits.
       
      Inspect for wires that are broken inside the insulation by gently pulling on suspect sections of wiring.
       

    4.  

    Related Diagnostic Trouble Codes (DTC)

    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009



    Click image to see an enlarged view

    Fig. Related Diagnostic Trouble Codes

    Throttle Position Sensor (TPS)

    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009

    A properly operating TPS should display a linear -sweep- of the entire throttle range, and should not exhibit any voltage drop or signal break. If the feedback signal is not within the specified range, additional diagnosis is required in order to determine the proper function of the TPS, or if a fault exists in any related sub-systems.

    Click image to see an enlarged view

    Fig. Throttle Position Sensor Range Chart

    Throttle Position Sensor (TPS) Strategy

    Specific to:

    Jeep Compass 2007-2009

    Jeep Patriot 2007-2009

    The TPS provides a linear input signal (See Figure 1) to the Powertrain Control Module (PCM), which is used to monitor the throttle position. The TPS monitors the entire range of throttle opening from 0.5 volts DC (0 percent) 4.5 volts DC (100 percent). In modern drive-by-wire throttle control systems, the TPS provides data to the PCM in order to calculate the desired throttle position, in addition to air-fuel mixture, ignition timing, fuel injector pulse width, and transmission/transaxle gear position.

    The TPS utilizes positive coefficient logic: as the accelerator position is increased, the voltage is increased.

     
    AutoZone Logo