AutoZone 1999 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl | Repair Guides | Chassis Electrical | Air Conditioner | Orifice Tube | AutoZone.com

Search suggestions

    My Vehicles

    1999 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 9:00 PM today

    SAVE 20% + GET A $10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OVER $100.

    Use Code: 20STACK10

    See Details

    Ford Taurus/Sable 1986-1995 Repair Information

    Orifice Tube

    Print

    Refer to Routine Maintenance for air conditioning system discharging information.

    The A/C evaporator core orifice should be replaced whenever the compressor is replaced for lack of performance.

    The A/C evaporator core orifice located in the condenser to evaporator tube cannot be serviced as a component of the line. If replacement is necessary, use the procedure for refrigerant line removal and installation located earlier in this section.

    An orifice tube replacement service kit may be used for an optional service procedure. The procedure for installation and removal of the service it are as follows:

    REMOVAL & INSTALLATION



    Fixed Orifice Tube Replacement Kit

    See Figures 1, 2, 3 and 4

    1. Disconnect the negative battery cable.
    2.  
    3. Discharge the refrigerant from the air conditioning system according to the proper procedure.
    4.  
    5. Remove the liquid line from the vehicle.
    6.  
    7. Locate the orifice tube by three indented notches or a circular depression in the metal portion of the liquid line. Note the angular position of the ends of the liquid line so that it can be reassembled in the correct position.
    8.  



    Click image to see an enlarged view

    Fig. Fig. 1: Locating the orifice tube

    1. Cut a 2 1 / 2 in. (63.5mm) section from the tube at the orifice tube location. Do not cut closer than 1 in. (25.4mm) from the start of the bend in the tube.
    2.  



    Click image to see an enlarged view

    Fig. Fig. 2: Cut a 21/2 in. section from the tube at the orifice tube location. Do NOT cut closer than 1 in. from the start of a bend in the tube

    1. Remove the orifice tube from the housing using pliers. An orifice tube removal tool cannot be used.
    2.  
    3. Flush the two pieces of liquid line to remove any contaminants.
    4.  
    5. Lubricate the O-rings with clean refrigerant oil and assemble the orifice tube kit, with the orifice tube installed, to the liquid line. Make sure the flow direction arrow is pointing toward the evaporator end of the liquid line and the taper of each compressor ring is toward the compressor nut.
    6.  

    The inlet tube will be positioned against the orifice tube tabs when correctly assembled.

    Click image to see an enlarged view

    Fig. Fig. 3: Exploded view of the A/C evaporator orifice tube kit

    1. While holding the hex of the tube in a vise, tighten each compression nut to 65-70 ft. lbs. (88-94 Nm) with a crow foot wrench.
    2.  



    Click image to see an enlarged view

    Fig. Fig. 4: With the nut in a vise, tighten each compression nut to the specified torque

    1. Assemble the liquid line to the vehicle using new O-rings lubricated with clean refrigerant oil. Use only the specified O-rings at the spring lock coupling.
    2.  
    3. Leak test, evacuate and charge the system according to the proper procedure. Observe all safety precautions.
    4.  
    5. Check the system for proper operation.
    6.  

     
    AutoZone Logo