AutoZone 1995 Toyota Paseo 1.5L EFI DOHC 4cyl | Repair Guides | Heating & Air Conditioning | Recirculation Door Actuator | Removal & Installation | AutoZone.com

Search suggestions

    My Vehicles

    1995 Toyota Paseo 1.5L EFI DOHC 4cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 10:00 PM today

    SAVE 20% + GET A $10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OVER $100.

    Use Code: 20STACK10

    See Details

    Avenger, Sebring Coupe, Stratus Coupe, 1999-2006

    Removal & Installation

    Print


    CAUTION
    On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death.

    1. Disconnect and isolate the negative battery cable.
    2.  
    3. Remove the instrument panel from the vehicle.
    4.  
    5. Disconnect the HVAC wire harness connector from the recirculation door actuator.

      Click image to see an enlarged view

      Fig. Recirculation housing (1) and actuator (2)

    6.  
    7. Remove the three screws that secure the recirculation door actuator to the HVAC air inlet housing.
      NOTE
      When removing the actuator, note the position of the actuator shaft and its respective linkage for installation reference.

    8.  
    9. Remove the recirculation door actuator from the HVAC air inlet housing.
    10.  

    To install:

    1. Install the recirculation door actuator onto the HVAC air inlet housing. If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the actuator gear.

      Click image to see an enlarged view

      Fig. Door gear (1), actuator gear (2) and recirculation housing (3)

    2.  
    3. Install the three screws that secure the recirculation door actuator to the HVAC air inlet housing. Tighten the screws to 18 inch lbs. (2 Nm).
    4.  
    5. Connect the wire harness connector to the recirculation door actuator.
    6.  
    7. Install the instrument panel.
    8.  
    9. Reconnect the negative battery cable.
    10.  


    CAUTION
    On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death.

    1. Before servicing the vehicle, refer to the Precautions Section.
    2.  
    3. Disconnect and isolate the negative battery cable.
    4.  
    5. Remove the instrument panel from the vehicle.
    6.  
    7. Disconnect the HVAC wire harness connector from the recirculation door actuator.

      Click image to see an enlarged view

      Fig. Recirculation housing (1) and actuator (2)

    8.  
    9. Remove the 3 screws that secure the recirculation door actuator to the HVAC air inlet housing.
      NOTE
      When removing the actuator, note the position of the actuator shaft and its respective linkage for installation reference.

    10.  
    11. Remove the recirculation door actuator from the HVAC air inlet housing.
    12.  

    To install:

    1. Install the recirculation door actuator onto the HVAC air inlet housing. If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the actuator gear.

      Click image to see an enlarged view

      Fig. Door gear (1), actuator gear (2), and recirculation housing (3)

    2.  
    3. Install the 3 screws that secure the recirculation door actuator to the HVAC air inlet housing. Tighten the screws to 18 inch lbs. (2 Nm).
    4.  
    5. Connect the wire harness connector to the recirculation door actuator.
    6.  
    7. Install the instrument panel.
    8.  
    9. Connect the negative battery cable.
    10.  

     
    AutoZone Logo