AutoZone 2002 Saturn SC2 1.9L MFI DOHC 4cyl | Repair Guides | Suspension & Steering | Rear Suspension | Rear Wheel Bearings | AutoZone.com

Search suggestions

    My Vehicles

    2002 Saturn SC2 1.9L MFI DOHC 4cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    CLOSED Open tomorrow at 7:30 AM

    Save 20% Sitewide

    Use Code: YOUCHOOSE20

    See Details

    Get A $25 Gift Card

    Use Code: YOUCHOOSE25

    See Details

    Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998

    Rear Wheel Bearings

    Print

    REMOVAL & INSTALLATION



    Cirrus, Stratus, Sebring Convertible and Breeze

    See Figures 1 through 6

    All vehicles are equipped with permanently lubricated and sealed-for-life rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.

    1. Raise and safely support the vehicle.
    2.  
    3. Remove the wheel and tire assembly.
    4.  
    5. Remove the brake drum or rotor.
    6.  



    Click image to see an enlarged view

    Fig. Fig. 1: Remove the dust cap using a hammer and chisel



    Click image to see an enlarged view

    Fig. Fig. 2: After loosening the cap, remove it from the center of the hub



    Click image to see an enlarged view

    Fig. Fig. 3: Using a breaker bar and socket, loosen the wheel hub/bearing center nut ...



    Click image to see an enlarged view

    Fig. Fig. 4: ... then remove the center nut from the vehicle



    Click image to see an enlarged view

    Fig. Fig. 5: Pull the wheel hub and bearing assembly straight off of the spindle

    1. Remove the rear hub dust cap.
    2.  
    3. Remove the rear hub retaining nut.
    4.  
    5. Remove the rear hub and bearing assembly by pulling it straight off the spindle.
    6.  

    To install:
    1. Install the replacement bearing on the rear spindle.
    2.  
    3. Install the hub with a new retaining nut.
    4.  



    Click image to see an enlarged view

    Fig. Fig. 6: Install the dust cap by tapping on it with a socket and a hammer

    1. Tighten the retaining nut to 185 ft. lbs. (250 Nm). Install the dust cap by tapping on it with a suitably sized socket and hammer.
    2.  
    3. Install the brake drum or rotor.
    4.  
    5. Install the wheel and tire assembly. Tighten the lug nuts in a star pattern to 95 ft. lbs. (129 Nm).
    6.  
    7. Lower the vehicle.
    8.  

    Sebring Coupe and Avenger

    See Figure 7

    1. Raise and safely support the vehicle.
    2.  
    3. Remove the appropriate wheel and tire assembly.
    4.  
    5. If equipped with an Anti-lock Brake System (ABS), remove the vehicle speed sensor.
    6.  
    7. Remove the brake drum or rotor from the hub assembly.
    8.  
    9. From the back of the knuckle, remove the four bolts securing the hub to the knuckle.
    10.  
    11. Remove the hub and bearing assembly from the knuckle.
    12.  

    The hub assembly is not serviceable and should not be disassembled.

    1. If replacing the hub, use special socket MB991248 and a press, to remove the wheel sensor rotor from the hub.
    2.  



    Click image to see an enlarged view

    Fig. Fig. 7: Wheel hub/bearing component assembly

    To install:
    1. Press the wheel sensor rotor onto the hub.
    2.  
    3. Install the hub to the knuckle and tighten the mounting bolts to 54-65 ft. lbs. (74-88 Nm).
    4.  
    5. Install the brake drum or rotor on the hub.
    6.  
    7. If equipped with ABS, install the vehicle speed sensor.
    8.  
    9. Install the wheel and tire assembly. Tighten the lug nuts in a star pattern to 95 ft. lbs. (129 Nm).
    10.  
    11. Lower the vehicle.
    12.  

     
    AutoZone Logo