AutoZone 2007 Ford Mustang 4.0L SFI SOHC 6cyl | Repair Guides | Engine & Engine Overhaul | Engine Mechanical | Rocker Arms | AutoZone.com

Search suggestions

    My Vehicles

    2007 Ford Mustang 4.0L SFI SOHC 6cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 10:00 PM today

    Save 20% Sitewide

    Use Code: YOUCHOOSE20

    See Details

    Get A $25 Gift Card

    Use Code: YOUCHOOSE25

    See Details

    GM Astro/Safari 1985-1996 Repair Guide

    Rocker Arms

    Print

    The rocker arms open and close the valves through a very simple ball pivot type operation.

    REMOVAL & INSTALLATION



    2.5L Engine

    See Figure 1



    Click image to see an enlarged view

    Fig. Fig. 1: Exploded view of the rocker arm assembly-2.5L engine

    1. Refer to the rocker arm (valve) cover, removal and installation procedures in this section and remove the valve cover.
    2.  
    3. Using a socket wrench, remove the rocker arm bolts, the ball washer and the rocker arm.
    4.  

    If only the pushrod is to be removed, back off the rocker arm bolt, swing the rocker arm aside and remove the pushrod. When removing more than assembly, at the same time, be sure to keep them in order for reassembly purposes.

    1. Inspect the rocker arms and ball washers for scoring and/or other damage, replace them (if necessary).
    2.  

    To install:

    If replacing worn components with new ones, be sure to coat the new parts with Molykote® or an equivalent engine assembly pre-lube, before installation.

    1. Install the pushrod and pushrod guide, if removed.
    2.  
    3. Loosely install the ball washer, rocker arms and bolts.
    4.  
    5. Adjust the valves:
      1. Rotate the crankshaft until the mark on the damper pulley aligns with the 0 mark on the timing plate and the No. 1 cylinder is on the compression stroke.
      2.  

    6.  

    To determine if the No. 1 cylinder is on the compression stroke, shake the rocker arms of the No. 1 cylinder, if they move the cylinder is on the compression stroke, if they don't move the cylinder is on the exhaust stroke. If the cylinder is on the exhaust stroke, it will be necessary to rotate the crankshaft one more full revolution to bring No. 1 back to top on compression.

    1. With the engine on the compression stroke, adjust the exhaust valves of cylinders No. 1 & 3 and the intake valves of cylinders No. 1 & 2.
    2.  
    3. To adjust the valves, tighten the rocker arm studs to the specified torque:

      1985-86: 20 ft. lbs. (28 Nm).
       
      1987: 24 ft. lbs. (32 Nm).
       
      1988-90: 22 ft. lbs. (30 Nm).
       

    4.  
    5. Rotate the crankshaft one complete revolution and align the mark on the damper pulley with the 0 mark on the timing plate.
    6.  
    7. With the engine on the No. 4 compression stroke, tighten the retainers for the exhaust valves of cylinders No. 2 & 4 and the intake valves of cylinders No. 3 & 4.
    8.  

    1. Install the rocker arm cover. For details, please refer to the procedure found earlier in this section.
    2.  

    4.3L Engine

    See Figures 2, 3, 4, 5, 6 and 7



    Click image to see an enlarged view

    Fig. Fig. 2: Exploded view of a 4.3L engine rocker arm assembly



    Click image to see an enlarged view

    Fig. Fig. 3: To remove the rocker arm, loosen and remove the nut and ball washer (pivot) ...



    Click image to see an enlarged view

    Fig. Fig. 4: ... then lift the rocker arm from the stud



    Click image to see an enlarged view

    Fig. Fig. 5: If necessary, remove the pushrod for replacement or inspection



    Click image to see an enlarged view

    Fig. Fig. 6: Keep ALL PARTS sorted or tagged for installation in their original locations



    Click image to see an enlarged view

    Fig. Fig. 7: Most 4.3L engines (except VIN W and some 1993-94 VIN Z models) will require valve lash adjustment during installation

    1. Refer to the Valve Cover, Removal and Installation procedures in this section and remove the valve covers.
    2.  
    3. Using a socket wrench remove the rocker arm-to-cylinder head nuts, the ball washers, the rocker arms and the pushrods (if necessary).
    4.  

    If you are removing more than one rocker arm, nut, washer and pushrod at a time, keep each assembly tagged, arranged and/or sorted to assure installation in their original locations.

    1. Inspect the parts for excessive wear and/or damage, then replace any parts (if necessary).
    2.  

    To install:

    If replacing any parts with new ones, coat the new parts with Molykote® or an equivalent engine assembly pre-lube.

    1. If removed, install the pushrod.
    2.  
    3. Loosely install the rocker arm, ball pivot and nut.
    4.  
    5. For the 4.3L (VIN W) engine and any 1993-94 4.3L (VIN Z) engines which are equipped with screw-in type rocker arm studs with positive stop shoulders, Tighten the rocker arm adjusting nuts against the stop shoulders to 20 ft. lbs. (27 Nm). No further adjustment is necessary, or possible.
    6.  
    7. For all 1985-92 and most later 4.3L (VIN B or Z) engines (which are not equipped with screw-in type rocker arm studs and positive stop shoulders), properly adjust the valve lash. For details on valve lash adjustment, please refer to General Information & Maintenance of this information.
    8.  
    9. Install the rocker arm cover(s) to the cylinder head.
    10.  

     
    AutoZone Logo