AutoZone | Repair Guides | Diagnostic Trouble Codes | Diagnostic Trouble Codes | Troublecodes (113 Of 130) | AutoZone.com

Search suggestions

    My Vehicles

    Add a Vehicle

    Find a Store

    Select Store

    Save 20% Sitewide

    Use Code: YOUCHOOSE20

    See Details

    Get A $25 Gift Card

    Use Code: YOUCHOOSE25

    See Details

    Kia_Sephia_Rio_Spectra_Optima_1998-2006

    TroubleCodes (113 of 130)

    Print

    2.7L V6 VIN 4 Std



    2.7L V6 VIN 4 Std

    Trouble Code: P0011

    A Camshaft Position Timing Over Advanced or System Performance (Bank 1)

    Trouble Code Conditions: Monitor deviation between camshaft position set point and actual value.

    Possible Causes:



    Oil leakage
     
    Faulty oil pump
     
    Faulty intake valve control solenoid
     

    Trouble Code: P0012

    A Camshaft Position- Timing Over retarded (Bank 1)

    Trouble Code Conditions: Determines if the phaser is stuck or has a steady error.

    Possible Causes:



    Engine oil
     
    OCV
     
    CVVT stuck
     
    Faulty PCM
     

    Trouble Code: P0016

    Crankshaft Position- Camshaft Position Correlation (Bank 1 Sensor A)

    Trouble Code Conditions: Monitor camshaft position in the full retard condition or during CVVT control. Camshaft switching out of 109 to 141 degrees in full retard position, 70 to 140 degrees CRK during CVVT control.

    Possible Causes:



    Abnormal installation of camshaft
     
    Abnormal installation of crankshaft
     
    Abnormal installation of tone wheel
     

    Trouble Code: P0018

    Crankshaft Position- Camshaft Position Correlation (Bank 2 Sensor A)

    Trouble Code Conditions: Determines if CAM (B2) target is aligned correctly to the crank. No active faults.

    Possible Causes:



    CKPS, CMPS (B2)
     
    CVVT
     
    Timing misalignment
     
    Faulty PCM
     

    Trouble Code: P0021

    A Camshaft Position- Timing Over Advanced Or System Performance (Bank 2)

    Trouble Code Conditions: Determines if the phaser is moving at an unexpected rate. Cam off set is available.

    Possible Causes:



    Excessive phasing
     
    Binding oil pressure (blockage)
     
    Faulty PCM
     

    Trouble Code: P0022

    A Camshaft Position- Timing Over Retarded (Bank 2)

    Trouble Code Conditions: Determines if the phaser is stuck or has a steady state error. Off sets available. Cam velocity below threshold at 15 CAD/s.

    Possible Causes:



    Engine oil
     
    OCV
     
    CVVT stuck
     
    Faulty PCM
     

    Trouble Code: P0026

    Intake Valve Control Solenoid Circuit Range/Performance (Bank 1)

    Trouble Code Conditions: Determines if oil control valve is stuck. Valve cleaning not in progress. Off sets available.

    Possible Causes:



    Oil pressure loss
     
    OCV seizure
     
    Faulty PCM
     

    Trouble Code: P0028

    Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)

    Trouble Code Conditions: Determines if oil control valve is stuck. Valve cleaning not in progress. Off sets available.

    Possible Causes:



    Oil pressure loss
     
    OCV seizure
     
    Faulty PCM
     

    Trouble Code: P0030

    HO2S-11 Heater Circuit Malfunction

    Trouble Code Conditions: Engine started, engine runtime over 3 minutes, and the PCM determined the resistance of the HO2S heater was more than a calculated amount.

    Possible Causes:



    HO2S heater control circuit is open or shorted to ground
     
    HO2S heater control circuit is shorted to system power (B+)
     
    HO2S heater is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0031

    O2 Sensor Heater Circuit Low (Bank 1/Sensor 1)

    Trouble Code Conditions: Heater check, low. Open or short circuit.

    Possible Causes:



    Open in battery and control circuit
     
    Short to ground in control circuit (pin 48 to 36)
     
    Faulty HO2S heater
     
    Faulty PCM
     

    Trouble Code: P0032

    O2 Sensor Heater Circuit High (Bank 1/Sensor 1)

    Trouble Code Conditions: Heater check, high. Short circuit.

    Possible Causes:



    Short to battery in control circuit
     
    Faulty HO2S heater
     
    Faulty PCM
     

    Trouble Code: P0036

    HO2S-12 Heater Circuit Malfunction

    Trouble Code Conditions: Engine started, engine runtime over 3 minutes, and the PCM determined the resistance of the HO2S heater was more than a calculated amount.

    Possible Causes:



    HO2S heater control circuit is open or shorted to ground
     
    HO2S heater control circuit is shorted to system power (B+)
     
    HO2S heater is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0037

    O2 Sensor Heater Circuit Low (Bank 1/Sensor 2)

    Trouble Code Conditions: Heater check, low. Open or short circuit.

    Possible Causes:



    Open in battery and control circuit
     
    Short to ground in control circuit (pin 48 to 36)
     
    Faulty HO2S heater
     
    Faulty PCM
     

    Trouble Code: P0038

    O2 Sensor Heater Circuit High (Bank 1/Sensor 2)

    Trouble Code Conditions: Heater check, high. Short circuit.

    Possible Causes:



    Short to battery in control circuit
     
    Faulty HO2S heater
     
    Faulty PCM
     

    Trouble Code: P0050

    OHO2S Heater Control Circuit High (Bank 2/Sensor 1)

    Trouble Code Conditions: Evaluate O2 sensor element temperature via measuring element resistance. Sensor preheating and full heating phases finished.

    Possible Causes:



    Related fuse blown or missing
     
    Heater control circuit open or short
     
    Power supply circuit open or short
     
    Contact resistance in connectors
     
    Faulty HO2S
     

    Trouble Code: P0051

    OHO2S Heater Circuit Low (Bank 2/Sensor 1)

    Trouble Code Conditions: Short circuit to ground on front HO2S heater line. Battery voltage above 10 volts.

    Possible Causes:



    Related fuse blown or missing
     
    Open or short to ground in power supply or control harness
     
    Contact resistance in connectors
     
    Faulty HO2S
     

    Trouble Code: P0052

    OHO2S Heater Circuit High (Bank 2/Sensor 1)

    Trouble Code Conditions: Open or short circuit to battery line on front HO2S heater line. Battery voltage above 10 volts.

    Possible Causes:



    Open or short to battery in control harness
     
    Contact resistance in connectors
     
    Faulty HO2S
     

    Trouble Code: P0056

    HO2S Heater Control Circuit (Bank 2/Sensor 2)

    Trouble Code Conditions: Evaluate O2 sensor element temperature via measuring element resistance. Sensor preheating and full heating phases finished.

    Possible Causes:



    Related fuse blown or missing
     
    Heater control circuit open or short
     
    Power supply circuit open or short
     
    Contact resistance in connections
     
    Faulty HO2S
     

    Trouble Code: P0057

    HO2S Heater Circuit Low (Bank 2/Sensor 2)

    Trouble Code Conditions: Check short circuit to ground on rear HO2S heater line.

    Possible Causes:



    Related fuse blown or missing
     
    Open or short to ground in power supply or control harness
     
    Contact resistance in connections
     
    Faulty HO2S
     

    Trouble Code: P0058

    HO2S Heater Circuit High (Bank 2/Sensor 2)

    Trouble Code Conditions: Check short circuit to ground on rear HO2S heater line.

    Possible Causes:



    Open or short to battery in control harness
     
    Contact resistance in connections
     
    Faulty HO2S
     

    Trouble Code: P0076

    Intake Valve Control Solenoid Circuit Low (Bank 1)

    Trouble Code Conditions: PCM sets the code if it detects that the intake valve control solenoid control circuit is short to ground. Electrical check.

    Possible Causes:



    Faulty ECM/PCM
     
    Short to ground in control circuit
     
    Contact resistance in connectors
     
    Faulty intake valve control solenoid
     

    Trouble Code: P0077

    Intake Valve Control Solenoid Circuit High (Bank 1)

    Trouble Code Conditions: PCM sets the code if it detects that the OCV control circuit is open or short to battery. Electrical check.

    Possible Causes:



    Open or short to battery in control circuit
     
    Contact resistance in connectors
     
    Faulty intake valve control solenoid
     
    Faulty PCM
     

    Trouble Code: P0082

    Intake Valve Control Solenoid Circuit Low (Bank 2)

    Trouble Code Conditions: Detects a short to ground or open circuit of VCPD bank 1 intake circuit output. No disabling faults present. Engine running. Enable time delay equal to or greater than 0.5 second.

    Possible Causes:



    Poor connection
     
    Open in power circuit
     
    Open or short to ground in control circuit
     
    OCV
     
    Faulty PCM
     

    Trouble Code: P0083

    Intake Valve Control Solenoid Circuit High (Bank 2)

    Trouble Code Conditions: Detects a short to battery of VCPD bank 1 intake circuit output. No disabling faults present. Engine running. Enable time delay equal to or greater than 0.5 second.

    Possible Causes:



    poor connection
     
    Short to battery in control circuit
     
    OCV
     
    Faulty PCM
     

    Trouble Code: P0100

    MAF Sensor Circuit Malfunction

    Trouble Code Conditions: Engine started, engine running, and the PCM detected the MAF sensor indicated less than 1 kg/h with the throttle angle more than 4.2 degrees, or that it indicated more than 520 kg/h at any time.

    Possible Causes:



    MAF sensor signal circuit open or shorted to ground
     
    MAF sensor signal circuit shorted to system power (B+)
     
    MAF sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0101

    MAF or Volume Airflow Sensor Performance

    Trouble Code Conditions: Engine started, engine running, and the PCM detected too much difference between the Actual MAF sensor signal and a Threshold MAF sensor value in memory during the CCM Rationality test.

    Possible Causes:



    MAF sensor signal circuit has high resistance
     
    MAF sensor ground circuit has high resistance
     
    MAF sensor is damaged or has failed (it may be contaminated)
     
    PCM has failed
     

    Trouble Code: P0102

    MAF Sensor Circuit Low Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the MAF sensor signal was less than 0.39 volt for more than 1 second.

    Possible Causes:



    MAF sensor signal circuit is shorted to ground
     
    MAF sensor power circuit open between sensor and main relay
     
    MAF sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0103

    MAF Sensor Circuit High Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the MAF sensor signal was more than 3.90 volts, condition met for 1 second.

    Possible Causes:



    MAF sensor signal circuit shorted to VREF or system power
     
    MAF sensor ground circuit is open between sensor and ground
     
    MAF sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0106

    Manifold Absolute Pressure Sensor Performance

    Trouble Code Conditions: Engine running and the PCM detected the MAP sensor signal was less than 2.20 volts but more than 0.40 volt during the CCM Rationality test.

    Possible Causes:



    Loss of 5-volt supply from the PCM (circuit open or grounded)
     
    MAP sensor signal circuit is open or grounded
     
    MAP sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0107

    Manifold Absolute Pressure Sensor Low Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the MAP sensor signal was less than 0.20 volt, condition met for 1 second.

    Possible Causes:



    Loss of 5-volt supply from the PCM (circuit open or grounded)
     
    MAP sensor signal circuit is shorted to ground
     
    MAP sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0108

    Manifold Absolute Pressure Sensor High Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the MAP sensor signal was more than 4.90 volts, condition met for 1 second.

    Possible Causes:



    MAP sensor ground circuit open
     
    MAP sensor signal circuit shorted to VREF or system power
     
    MAP sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0110

    Intake Air Temperature Sensor Circuit Malfunction

    Trouble Code Conditions: Engine runtime over 600 seconds and the PCM detected the IAT signal indicated more than 262(F, or that it indicated less than -38°F at any time during the CCM test.

    Possible Causes:



    IAT sensor signal circuit open or shorted to ground
     
    IAT sensor signal circuit shorted to VREF or system power
     
    IAT sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0111

    Intake Air temperature Sensor 1 Circuit Range/Performance

    Trouble Code Conditions: If the sensor is out of specification, a code is set. Output voltage is monitored. Engine coolant is above 167 degrees F. Vehicle speed is above 30MPH for more than 60 seconds. Vehicle speed is below 7mph for more than 30 seconds.

    Possible Causes:



    Poor connection
     
    Faulty IATS
     
    Faulty PCM
     

    Trouble Code: P0112

    Intake Air Temperature Sensor Circuit Low Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the IAT sensor signal was less than 0.2 volt during the CCM test.

    Possible Causes:



    IAT sensor signal circuit shorted to ground
     
    IAT sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0113

    Intake Air Temperature Sensor Circuit High Input

    Trouble Code Conditions: Key on or the engine running and the PCM detected the IAT sensor signal was more than 4.9 volts during the CCM test.

    Possible Causes:



    IAT sensor signal circuit shorted to VREF or system power
     
    IAT sensor ground circuit is open
     
    IAT sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0115

    Engine Coolant Temperature Sensor Circuit Malfunction

    Trouble Code Conditions: Engine runtime over 600 seconds, and the PCM detected the IAT signal indicated more than 280°F, or that it indicated less than -38°F at any time during the CCM test.

    Possible Causes:



    ECT sensor signal circuit open or shorted to ground
     
    ECT sensor signal circuit shorted to VREF or system power
     
    ECT sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0116

    Engine Coolant Temperature Sensor Range/Performance

    Trouble Code Conditions: Engine running for 20 minutes, and the PCM detected an ECT signal remained at less than a specified value during the CCM test period.

    Possible Causes:



    Check for low coolant level or incorrect coolant mixture
     
    Cooling system component failure (thermostat stuck open)
     
    ECT sensor is out of calibration or it is "skewed"
     
    ECT sensor is damaged or has failed
     

    Trouble Code: P0117

    Engine Coolant Temperature Sensor Circuit Low Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the ECT sensor signal was less than 0.20 volt during the CCM test.

    Possible Causes:



    ECT sensor signal circuit shorted to ground
     
    ECT sensor is damaged or has failed
     
    PCM has failed
     

    Trouble Code: P0118

    Engine Coolant Temperature Sensor Circuit High Input

    Trouble Code Conditions: Key on or engine running and the PCM detected the ECT sensor signal was more than 4.90 volts during the CCM test.

    Possible Causes:



    ECT sensor signal circuit is open between sensor and the PCM
     
    ECT sensor ground circuit is open between sensor and ground
     
    ECT sensor signal circuit is shorted to VREF
     
    ECT sensor is damaged or has failed
     
    PCM has failed
     

     
    AutoZone Logo