AutoZone 1988 Audi 5000 S Quattro 2.3L MFI SOHC 5cyl | Repair Guides | Brakes | Rear Drum Brakes | Brake Drums | AutoZone.com

Search suggestions

    My Vehicles

    1988 Audi 5000 S Quattro 2.3L MFI SOHC 5cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 10:00 PM today

    SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE.

    Use Code: SEECLEAR

    See Details

    Mazda Tribute 2001-06

    Brake Drums

    Print

    Removal & Installation



    1. Remove the tire and wheel assembly.
    2.  


      Click image to see an enlarged view

      Fig. Drum brake exploded view



    CAUTION
    Use of a brake drum puller or a torch is not recommended. Brake drum distortion can result.


    NOTE
    If the brake drum is rusted to the axle shaft pilot diameter, tap the center of the brake drum between the wheel studs.

    1. Remove the brake drum.
    2.  
    3. If equipped, remove the brake drum retaining clips.
    4.  
    5. If the brake drums will not come off, follow these steps.
    6.  
    7. Move the brake shoe adjusting lever off the brake adjuster screw.
    8.  
    9. Loosen the brake shoe adjuster screw nut by adjusting the nut upward.
    10.  
    11. Using the special tool, 134-R0191, measure the brake drum inside diameter.
    12.  
    13. Install a new brake drum if the maximum inside diameter exceeds the specification shown on the outside of the brake drum.
    14.  

    To install:


    WARNING
    Whenever a wheel is installed, always remove any corrosion, dirt or foreign material present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Failure to follow these instructions may result in personal injury.

    1. Clean the wheel hub mounting surface and wheel pilot.
    2.  
    3. Install the tire and wheel assembly.
    4.  



    Click image to see an enlarged view

    Fig. Drum brake and related components

    1. Before servicing the vehicle, refer to the Precautions Section.
    2.  
    3. Raise and support the vehicle safely.
    4.  
    5. Remove the wheel and tire assembly.
      CAUTION
      Use of a brake drum puller or a torch is not recommended. Brake drum distortion can result.


      NOTE
      If the brake drum is rusted to the axle shaft pilot diameter, tap the center of the brake drum between the wheel studs.

    6.  
    7. Remove the brake drum.
    8.  
    9. If equipped, remove the brake drum retaining clips.
    10.  
    11. If the brake drums will not come off, follow these steps.
    12.  
    13. Move the brake shoe adjusting lever off the brake adjuster screw.
    14.  
    15. Loosen the brake shoe adjuster screw nut by adjusting the nut upward.
    16.  
    17. Using the special tool, 134-R0191, measure the brake drum inside diameter.
    18.  
    19. Install a new brake drum if the maximum inside diameter exceeds specification.
    20.  

    To install:


    WARNING
    Whenever a wheel is installed, always remove any corrosion, dirt or foreign material present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Failure to follow these instructions may result in personal injury.

    1. Clean the wheel hub mounting surface and wheel pilot.
    2.  
    3. Install the tire and wheel assembly.
    4.  

     
    AutoZone Logo