AutoZone 1999 Ford Mustang Cobra 4.6L SFI DOHC 8cyl | Repair Guides | Steering | Power Rack & Pinion Steering Gear | Removal & Installation | AutoZone.com

Search suggestions

    My Vehicles

    1999 Ford Mustang Cobra 4.6L SFI DOHC 8cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    CLOSED Open at 7:30 AM

    SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE.

    Use Code: SEECLEAR

    See Details

    Toyota Sienna 2000-06

    Removal & Installation

    Print



    Click image to see an enlarged view

    Fig. Exploded view of the power steering gear and related components-2001-03

    1. Before servicing the vehicle, refer to the Precautions section.
    2.  
    3. Remove or disconnect the following:

      Negative battery cable
       

    4.  


    NOTE
    Wait at least 90 seconds before working on the vehicle to allow the Supplemental Restraint System (SRS) system to disarm.



    Right and left side fender apron seals
     
    Right and left tie rod ends
     

    1. Place matchmarks on the intermediate shaft.
    2.  
    3. Remove or disconnect the following:

      Pinch bolt and the intermediate shaft out from under the vehicle
       
      Power steering line clamp
       
      Pressure and feed lines
       
      Stabilizer bar, unbolt it but do not remove it
       
      Heated Oxygen (HO2) sensor
       
      Both gear assembly set bolts and nuts, by lifting the stabilizer bar
       
      Gear assembly from the left side of the vehicle
       

    4.  

    To install:

    1. Install or connect the following:

      Gear assembly to the left side of the vehicle
       

    2.  


    WARNING
    Be careful not to damage the power steering lines.



    Tighten the gear assembly set bolts and nuts to 134 ft. lbs. (181 Nm), by lifting the stabilizer bar
     
    HO2 sensor
     
    Stabilizer bar. Tighten the bolt to 14 ft. lbs. (19 Nm) and the nut to 29 ft. lbs. (39 Nm).
     
    Pressure and feed return lines. Tighten them to 18 ft. lbs. (25 Nm).
     
    Line clamps. Tighten the nut to 84 inch lbs. (10 Nm).
     
    Intermediate shaft, by aligning the joint and main shaft matchmarks. Tighten to 26 ft. lbs. (35 Nm).
     
    Tie rod ends
     
    Fender apron seals. Securely tighten the bolts.
     

    1. Remove or disconnect the following:

      Steering wheel pad
       
      Steering wheel
       

    2.  
    3. Position the front wheels facing straight-ahead. Do this with the front of the vehicle on jackstands.
    4.  
    5. Center the spiral cable.
    6.  
    7. Install the steering wheel at the straight-ahead position. Temporarily tighten the wheel set nut. Attach the wiring.
    8.  
    9. Bleed the power steering system.
    10.  
    11. Check the steering wheel center point. Tighten the steering nut to 26 ft. lbs. (35 Nm).
    12.  
    13. Check and/or adjust the front wheel alignment.
    14.  



    Click image to see an enlarged view

    Fig. Steering gear and related parts-2004 models

    1. Place the wheels in a straight-ahead position.
    2.  
    3. Remove the wheels.
    4.  
    5. Matchmark and remove the intermediate shaft from the gear.
    6.  
    7. Remove the steering column hole cover from the dash panel.
    8.  
    9. Disconnect the tie rod ends.
    10.  
    11. Disconnect the stabilizer bar.
    12.  
    13. Disconnect the pressure and return lines.
    14.  
    15. Remove the 2 gear mounting bolts.
    16.  
    17. Matchmark the intermediate shaft extension and control valve shaft.
    18.  
    19. Remove the intermediate shaft extension bolt and remove the gear.
    20.  

    To install:

    1. Place the gear in position. Align the matchmarks and connect the intermediate extension shaft. Torque to 27 ft. lbs. (36 Nm).
    2.  
    3. Install the column cover plate and clamp.
    4.  
    5. Install the gear mounting bolts. Torque to 52 ft. lbs. (70 Nm).
    6.  
    7. Connect the stabilizer bar. Torque to 12 ft. lbs. (17 Nm).
    8.  
    9. Connect the tie rods ends. Torque to 36 ft. lbs. (49 Nm).
    10.  
    11. Connect the intermediate shaft. Torque to 26 ft. lbs. (36 Nm).
    12.  
    13. Check the alignment.
    14.  



    Click image to see an enlarged view

    Fig. Exploded view of the power steering gear and related components

    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2.  
    3. Remove or disconnect the following:
      NOTE
      Wait at least 90 seconds before working on the vehicle to allow the Supplemental Restraint System (SRS) system to disarm.



      Negative battery cable
       



      Right and left side fender apron seals
       
      Right and left tie rod ends
       

    4.  
    5. Place matchmarks on the intermediate shaft.
    6.  
    7. Remove or disconnect the following:

      Pinch bolt and the intermediate shaft out from under the vehicle
       
      Power steering line clamp
       
      Pressure and feed lines
       
      Stabilizer bar, unbolt it but do not remove it
       
      Heated Oxygen (HO 2 ) sensor
       
      Both gear assembly set bolts and nuts, by lifting the stabilizer bar
       
      Gear assembly from the left side of the vehicle
       

    8.  

    To install:

    1. Install or connect the following:
      WARNING
      Be careful not to damage the power steering lines.



      Gear assembly to the left side of the vehicle
       



      Tighten the gear assembly set bolts and nuts to 134 ft. lbs. (181 Nm), by lifting the stabilizer bar
       
      HO 2 sensor
       
      Stabilizer bar. Tighten the bolt to 14 ft. lbs. (19 Nm) and the nut to 29 ft. lbs. (39 Nm).
       
      Pressure and feed return lines. Tighten them to 18 ft. lbs. (25 Nm).
       
      Line clamps. Tighten the nut to 84 inch lbs. (10 Nm).
       
      Intermediate shaft, by aligning the joint and main shaft matchmarks. Tighten to 26 ft. lbs. (35 Nm).
       
      Tie rod ends
       
      Fender apron seals. Securely tighten the bolts.
       

    2.  
    3. Remove or disconnect the following:

      Steering wheel pad
       
      Steering wheel
       

    4.  
    5. Position the front wheels facing straight-ahead. Do this with the front of the vehicle on jackstands.
    6.  
    7. Center the spiral cable.
    8.  
    9. Install the steering wheel at the straight-ahead position. Temporarily tighten the wheel set nut. Attach the wiring.
    10.  
    11. Bleed the power steering system.
    12.  
    13. Check the steering wheel center point. Tighten the steering nut to 26 ft. lbs. (35 Nm).
    14.  
    15. Check and/or adjust the front wheel alignment.
    16.  



    Click image to see an enlarged view

    Fig. Exploded view of the power steering gear and related components-2000-03

    1. Before servicing the vehicle, refer to the precautions section.
    2.  
    3. Remove or disconnect the following:
      NOTE
      Wait at least 90 seconds before working on the vehicle to allow the Supplemental Restraint System (SRS) system to disarm.



      Negative battery cable
       



      Right and left side fender apron seals
       
      Right and left tie rod ends
       

    4.  
    5. Place matchmarks on the intermediate shaft.
    6.  
    7. Remove or disconnect the following:

      Pinch bolt and the intermediate shaft out from under the vehicle
       
      Power steering line clamp
       
      Pressure and feed lines
       
      Stabilizer bar, unbolt it but do not remove it
       
      Heated Oxygen (HO 2 ) sensor
       
      Both gear assembly set bolts and nuts, by lifting the stabilizer bar
       
      Gear assembly from the left side of the vehicle
       

    8.  

    To install:

    1. Install or connect the following:
      WARNING
      Be careful not to damage the power steering lines.



      Gear assembly to the left side of the vehicle
       



      Tighten the gear assembly set bolts and nuts to 134 ft. lbs. (181 Nm), by lifting the stabilizer bar
       
      HO 2 sensor
       
      Stabilizer bar. Tighten the bolt to 14 ft. lbs. (19 Nm) and the nut to 29 ft. lbs. (39 Nm).
       
      Pressure and feed return lines. Tighten them to 18 ft. lbs. (25 Nm).
       
      Line clamps. Tighten the nut to 84 inch lbs. (10 Nm).
       
      Intermediate shaft, by aligning the joint and main shaft matchmarks. Tighten to 26 ft. lbs. (35 Nm).
       
      Tie rod ends
       
      Fender apron seals. Securely tighten the bolts.
       

    2.  
    3. Remove or disconnect the following:

      Steering wheel pad
       
      Steering wheel
       

    4.  
    5. Position the front wheels facing straight-ahead. Do this with the front of the vehicle on jackstands.
    6.  
    7. Center the spiral cable.
    8.  
    9. Install the steering wheel at the straight-ahead position. Temporarily tighten the wheel set nut. Attach the wiring.
    10.  
    11. Bleed the power steering system.
    12.  
    13. Check the steering wheel center point. Tighten the steering nut to 26 ft. lbs. (35 Nm).
    14.  
    15. Check and/or adjust the front wheel alignment.
    16.  



    Click image to see an enlarged view

    Fig. Steering gear and related parts-2004-06 models

    1. Place the wheels in a straight-ahead position.
    2.  
    3. Remove the wheels.
    4.  
    5. Matchmark and remove the intermediate shaft from the gear.
    6.  
    7. Remove the steering column hole cover from the dash panel.
    8.  
    9. Disconnect the tie rod ends.
    10.  
    11. Disconnect the stabilizer bar.
    12.  
    13. Disconnect the pressure and return lines.
    14.  
    15. Remove the 2 gear mounting bolts.
    16.  
    17. Matchmark the intermediate shaft extension and control valve shaft.
    18.  
    19. Remove the intermediate shaft extension bolt and remove the gear.
    20.  

    To install:

    1. Place the gear in position. Align the matchmarks and connect the intermediate extension shaft. Torque to 27 ft. lbs. (36 Nm).
    2.  
    3. Install the column cover plate and clamp.
    4.  
    5. Install the gear mounting bolts. Torque to 52 ft. lbs. (70 Nm).
    6.  
    7. Connect the stabilizer bar. Torque to 12 ft. lbs. (17 Nm).
    8.  
    9. Connect the tie rods ends. Torque to 36 ft. lbs. (49 Nm).
    10.  
    11. Connect the intermediate shaft. Torque to 26 ft. lbs. (36 Nm).
    12.  
    13. Check the alignment.
    14.  

     
    AutoZone Logo