AutoZone 1979 Buick Skyhawk 3.8L 2BL OHV 6cyl | Repair Guides | Brakes | Rear Drum Brakes | Brake Shoes | AutoZone.com

Search suggestions

    My Vehicles

    1979 Buick Skyhawk 3.8L 2BL OHV 6cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 10:00 PM today

    SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OVER $100.

    Use Code: FALLSAVINGS

    See Details

    Toyota Sienna 2000-06

    Brake Shoes

    Print

    Adjustment



    2000-03
    1. Before servicing the vehicle, refer to the precautions section.
    2.  
    3. Remove the rear wheels.
    4.  
    5. Measure the brake drum inside diameter and the diameter of the installed brake shoe assembly.
    6.  
    7. Turn the brake shoe adjuster to either retract or expand the brake shoe assembly until the diameter of the brake she assembly is slightly less than that of the drum.
    8.  
    9. Install the drum, and turn the wheel/drum assembly. There should be a hardly noticeable drag as the drum is turned.
    10.  
    11. Install the wheel and pump the brake pedal several times to fully seat the brakes.
    12.  
    13. Start the vehicle and very slowly drive back and forwards. Driving backwards and applying the brake pedal causes the rear brake adjuster to self adjust.
      NOTE
      Do not drive backwards at high speeds, for long distances or apply the brakes too hard. A slow speed under 1 mile per hour for a short distance and plying the brake will help the adjuster to self adjust.



      Click image to see an enlarged view

      Fig. Measure the brake drum inside diameter and the diameter of the installed brake shoe assembly-Sienna

    14.  

    2004-06
    1. Before servicing the vehicle, refer to the precautions section.
    2.  
    3. Remove the rear wheels.
    4.  
    5. Measure the brake drum inside diameter and the diameter of the installed brake shoe assembly.
    6.  
    7. Turn the brake shoe adjuster to either retract or expand the brake shoe assembly until the diameter of the brake she assembly is slightly less than that of the drum.
    8.  
    9. Install the drum, and turn the adjuster to expand the shoes until the drum locks.
    10.  
    11. Back off the adjuster 15 notches and install the hole plug.
    12.  

    Removal & Installation



    1. Disconnect the negative battery cable from the battery.
    2.  
    3. Loosen the rear wheel lug nuts slightly. Release the parking brake.
    4.  
    5. Block the front wheels, raise the rear of the vehicle, and safely support it with jackstands.
    6.  
    7. Remove the wheel lug nuts and the wheel.
    8.  
    9. Remove the brake drum retaining screws, if equipped. Remove the brake drum.
    10.  
    11. If the drum is difficult to remove, perform the following:
      1. Insert the end of a bent wire (a coat hanger will do nicely) through the hole in the brake drum and hold the automatic adjusting lever away from the adjuster.
      2.  
      3. Reduce the brake shoe adjustment by turning the adjuster bolt with a brake tool.
      4.  
      5. The drum should now be loose enough to remove without much effort.
      6.  

    12.  
    13. Carefully unhook the return spring from the leading (front) brake shoe.
    14.  
    15. Press the hold down spring retainer in and turn the pin on the front brake shoe.
    16.  
    17. Remove the hold down spring, retainers and the pin for the front brake shoe.
    18.  
    19. Pull out the brake shoe and unhook the anchor spring from the lower edge.
    20.  
    21. Remove the hold down spring from the trailing (rear) shoe. Pull the shoe out with the adjuster, automatic adjuster assembly and springs attached. Disconnect the parking brake cable. Remove the tension/return and anchor springs from the rear shoe.
    22.  
    23. Unhook the adjusting lever spring from the rear shoe and then remove the automatic adjuster assembly.
    24.  


      Click image to see an enlarged view

      Fig. Exploded view of the rear drum brake components-Sienna


    To install:

    1. Inspect the shoes for signs of unusual wear or scoring.
    2.  
    3. Check the wheel cylinder for any sign of fluid seepage or frozen pistons.
    4.  
    5. Clean and inspect the brake backing plate and all other components. Check that the brake drum inner diameter is within specified limits. Lubricate the backing plate at the positions the brakes come in contact with the backing plate. Also lubricate the anchor plate.
    6.  
    7. Mount the automatic adjuster assembly onto a new rear brake shoe.
    8.  
    9. Connect the parking brake cable to the rear shoe and then install the automatic adjusting lever, spring and E-ring. Position the rear shoe so the lower end rides in the anchor plate and the upper end is against the boot of the wheel cylinder.
    10.  
    11. Install the pin and the hold down spring. Press the retainer down over the pin and rotate the pin so the crimped edge is held by the retainer.
    12.  
    13. Place the front brake into position and install the anchor spring between the front and rear shoes. Stretch the spring enough so the front shoe will fit as the rear did. Install the hold down spring, pin and retainer to the front brake shoe.
    14.  
    15. Connect the return spring to the front brake shoe.
    16.  
    17. Check the operation of the automatic adjuster mechanism:
      1. Apply the parking brake lever and verifying the adjusting bolt turns.
      2.  
      3. Adjust the strut to where it is the shortest possible length.
      4.  
      5. Install the brake drum.
      6.  
      7. Apply the parking brake lever until the clicking sound can no longer be heard.
      8.  

    18.  
    19. Check the clearance between the brake shoes and drum:
      1. Remove the brake drum.
      2.  
      3. Measure the brake drum inside diameter and diameter of the brake shoes. The difference is "Shoe-to-drum clearance" and should be approximately 0.024 inch (0.6mm). If incorrect, check the parking brake system.
      4.  

    20.  


    NOTE
    A special brake caliper tool is required to gauge the brake drum inside diameter and shoe-to-drum clearance. However it is not required to perform brake shoe adjustment.

    1. Install the brake drum.
    2.  
    3. Adjust the brake pedal until a slight drag is felt when the drum is spun by hand.
    4.  
    5. Pull the parking lever all the way up until a clicking sound can no longer be heard. Check the clearance between brake shoes and brake drum.
    6.  
    7. Install the rear wheels, tighten the wheel lug nuts and lower the vehicle.
    8.  
    9. Retighten the wheel lug nuts and pump the brake pedal a few times before moving the vehicle. Adjust the rear brakes again if necessary.
    10.  
    11. Check the level of brake fluid in the master cylinder, then perform a test drive.
    12.  
    13. Connect the negative battery cable to the battery.
    14.  

    1. Before servicing the vehicle, refer to the precautions section.
    2.  
    3. Disconnect the negative battery cable from the battery.

      Click image to see an enlarged view

      Fig. Exploded view of the rear drum brake components-Sienna

    4.  
    5. Loosen the rear wheel lug nuts slightly. Release the parking brake.
    6.  
    7. Block the front wheels, raise the rear of the vehicle, and safely support it with jackstands.
    8.  
    9. Remove the wheel lug nuts and the wheel.
    10.  
    11. Remove the brake drum retaining screws, if equipped. Remove the brake drum.
    12.  
    13. If the drum is difficult to remove, perform the following:
      1. Insert the end of a bent wire (a coat hanger will do nicely) through the hole in the brake drum and hold the automatic adjusting lever away from the adjuster.
      2.  
      3. Reduce the brake shoe adjustment by turning the adjuster bolt with a brake tool.
      4.  
      5. The drum should now be loose enough to remove without much effort.
      6.  

    14.  
    15. Carefully unhook the return spring from the leading (front) brake shoe.
    16.  
    17. Press the hold down spring retainer in and turn the pin on the front brake shoe.
    18.  
    19. Remove the hold down spring, retainers and the pin for the front brake shoe.
    20.  
    21. Pull out the brake shoe and unhook the anchor spring from the lower edge.
    22.  
    23. Remove the hold down spring from the trailing (rear) shoe. Pull the shoe out with the adjuster, automatic adjuster assembly and springs attached. Disconnect the parking brake cable. Remove the tension/return and anchor springs from the rear shoe.
    24.  
    25. Unhook the adjusting lever spring from the rear shoe and then remove the automatic adjuster assembly.
    26.  

    To install:

    1. Inspect the shoes for signs of unusual wear or scoring.
    2.  
    3. Check the wheel cylinder for any sign of fluid seepage or frozen pistons.
    4.  
    5. Clean and inspect the brake backing plate and all other components. Check that the brake drum inner diameter is within specified limits. Lubricate the backing plate at the positions the brakes come in contact with the backing plate. Also lubricate the anchor plate.
    6.  
    7. Mount the automatic adjuster assembly onto a new rear brake shoe.
    8.  
    9. Connect the parking brake cable to the rear shoe and then install the automatic adjusting lever, spring and E-ring. Position the rear shoe so the lower end rides in the anchor plate and the upper end is against the boot of the wheel cylinder.
    10.  
    11. Install the pin and the hold down spring. Press the retainer down over the pin and rotate the pin so the crimped edge is held by the retainer.
    12.  
    13. Place the front brake into position and install the anchor spring between the front and rear shoes. Stretch the spring enough so the front shoe will fit as the rear did. Install the hold down spring, pin and retainer to the front brake shoe.
    14.  
    15. Connect the return spring to the front brake shoe.
    16.  
    17. Check the operation of the automatic adjuster mechanism:
      1. Apply the parking brake lever and verifying the adjusting bolt turns.
      2.  
      3. Adjust the strut to where it is the shortest possible length.
      4.  
      5. Install the brake drum.
      6.  
      7. Apply the parking brake lever until the clicking sound can no longer be heard.
      8.  

    18.  
    19. Check the clearance between the brake shoes and drum:
      1. Remove the brake drum.
      2.  
      3. Measure the brake drum inside diameter and diameter of the brake shoes. The difference is "Shoe-to-drum clearance" and should be approximately 0.024 inch (0.6mm). If incorrect, check the parking brake system.
        NOTE
        A special brake caliper tool is required to gauge the brake drum inside diameter and shoe-to-drum clearance. However it is not required to perform brake shoe adjustment.

      4.  

    20.  
    21. Install the brake drum.
    22.  
    23. Adjust the brake pedal until a slight drag is felt when the drum is spun by hand.
    24.  
    25. Pull the parking lever all the way up until a clicking sound can no longer be heard. Check the clearance between brake shoes and brake drum.
    26.  
    27. Install the rear wheels, tighten the wheel lug nuts and lower the vehicle.
    28.  
    29. Retighten the wheel lug nuts and pump the brake pedal a few times before moving the vehicle. Adjust the rear brakes again if necessary.
    30.  
    31. Check the level of brake fluid in the master cylinder, then perform a test drive.
    32.  
    33. Connect the negative battery cable to the battery.
    34.  

    RAV4 And Sienna
    1. Disconnect the negative battery cable from the battery.

      Click image to see an enlarged view

      Fig. Exploded view of the rear drum brake components-Previa



      Click image to see an enlarged view

      Fig. Exploded view of the rear drum brake components-Sienna

    2.  
    3. Loosen the rear wheel lug nuts slightly. Release the parking brake.
    4.  
    5. Block the front wheels, raise the rear of the vehicle, and safely support it with jackstands.
    6.  
    7. Remove the wheel lug nuts and the wheel.
    8.  
    9. Remove the brake drum retaining screws, if equipped. Remove the brake drum.
    10.  
    11. If the drum is difficult to remove, perform the following:
      1. Insert the end of a bent wire (a coat hanger will do nicely) through the hole in the brake drum and hold the automatic adjusting lever away from the adjuster.
      2.  
      3. Reduce the brake shoe adjustment by turning the adjuster bolt with a brake tool.
      4.  
      5. The drum should now be loose enough to remove without much effort.
      6.  

    12.  
    13. Carefully unhook the return spring from the leading (front) brake shoe.
    14.  
    15. Press the hold down spring retainer in and turn the pin on the front brake shoe.
    16.  
    17. Remove the hold down spring, retainers and the pin for the front brake shoe.
    18.  
    19. Pull out the brake shoe and unhook the anchor spring from the lower edge.
    20.  
    21. Remove the hold down spring from the trailing (rear) shoe. Pull the shoe out with the adjuster, automatic adjuster assembly and springs attached. Disconnect the parking brake cable. Remove the tension/return and anchor springs from the rear shoe.
    22.  
    23. Unhook the adjusting lever spring from the rear shoe and then remove the automatic adjuster assembly.
    24.  

    To install:

    1. Inspect the shoes for signs of unusual wear or scoring.
    2.  
    3. Check the wheel cylinder for any sign of fluid seepage or frozen pistons.
    4.  
    5. Clean and inspect the brake backing plate and all other components. Check that the brake drum inner diameter is within specified limits. Lubricate the backing plate at the positions the brakes come in contact with the backing plate. Also lubricate the anchor plate.
    6.  
    7. Mount the automatic adjuster assembly onto a new rear brake shoe.
    8.  
    9. Connect the parking brake cable to the rear shoe and then install the automatic adjusting lever, spring and E-ring. Position the rear shoe so the lower end rides in the anchor plate and the upper end is against the boot of the wheel cylinder.
    10.  
    11. Install the pin and the hold down spring. Press the retainer down over the pin and rotate the pin so the crimped edge is held by the retainer.
    12.  
    13. Place the front brake into position and install the anchor spring between the front and rear shoes. Stretch the spring enough so the front shoe will fit as the rear did. Install the hold down spring, pin and retainer to the front brake shoe.
    14.  
    15. Connect the return spring to the front brake shoe.
    16.  
    17. Check the operation of the automatic adjuster mechanism:
      1. Apply the parking brake lever and verifying the adjusting bolt turns.
      2.  
      3. Adjust the strut to where it is the shortest possible length.
      4.  
      5. Install the brake drum.
      6.  
      7. Apply the parking brake lever until the clicking sound can no longer be heard.
      8.  

    18.  
    19. Check the clearance between the brake shoes and drum:
      1. Remove the brake drum.
      2.  
      3. Measure the brake drum inside diameter and diameter of the brake shoes. The difference is "Shoe-to-drum clearance" and should be approximately 0.024 inch (0.6mm). If incorrect, check the parking brake system.
        NOTE
        A special brake caliper tool is required to gauge the brake drum inside diameter and shoe-to-drum clearance. However it is not required to perform brake shoe adjustment.

      4.  

    20.  
    21. Install the brake drum.
    22.  
    23. Adjust the brake pedal until a slight drag is felt when the drum is spun by hand.
    24.  
    25. Pull the parking lever all the way up until a clicking sound can no longer be heard. Check the clearance between brake shoes and brake drum.
    26.  
    27. Install the rear wheels, tighten the wheel lug nuts and lower the vehicle.
    28.  
    29. Retighten the wheel lug nuts and pump the brake pedal a few times before moving the vehicle. Adjust the rear brakes again if necessary.
    30.  
    31. Check the level of brake fluid in the master cylinder, then perform a test drive.
    32.  
    33. Connect the negative battery cable to the battery.
    34.  

    Sienna
    1. Disconnect the negative battery cable from the battery.

      Click image to see an enlarged view

      Fig. Exploded view of the rear drum brake components-Sienna

    2.  
    3. Loosen the rear wheel lug nuts slightly. Release the parking brake.
    4.  
    5. Block the front wheels, raise the rear of the vehicle, and safely support it with jackstands.
    6.  
    7. Remove the wheel lug nuts and the wheel.
    8.  
    9. Remove the brake drum retaining screws, if equipped. Remove the brake drum.
    10.  
    11. If the drum is difficult to remove, perform the following:
      1. Insert the end of a bent wire (a coat hanger will do nicely) through the hole in the brake drum and hold the automatic adjusting lever away from the adjuster.
      2.  
      3. Reduce the brake shoe adjustment by turning the adjuster bolt with a brake tool.
      4.  
      5. The drum should now be loose enough to remove without much effort.
      6.  

    12.  
    13. Carefully unhook the return spring from the leading (front) brake shoe.
    14.  
    15. Press the hold down spring retainer in and turn the pin on the front brake shoe.
    16.  
    17. Remove the hold down spring, retainers and the pin for the front brake shoe.
    18.  
    19. Pull out the brake shoe and unhook the anchor spring from the lower edge.
    20.  
    21. Remove the hold down spring from the trailing (rear) shoe. Pull the shoe out with the adjuster, automatic adjuster assembly and springs attached. Disconnect the parking brake cable. Remove the tension/return and anchor springs from the rear shoe.
    22.  
    23. Unhook the adjusting lever spring from the rear shoe and then remove the automatic adjuster assembly.
    24.  

    To install:

    1. Inspect the shoes for signs of unusual wear or scoring.
    2.  
    3. Check the wheel cylinder for any sign of fluid seepage or frozen pistons.
    4.  
    5. Clean and inspect the brake backing plate and all other components. Check that the brake drum inner diameter is within specified limits. Lubricate the backing plate at the positions the brakes come in contact with the backing plate. Also lubricate the anchor plate.
    6.  
    7. Mount the automatic adjuster assembly onto a new rear brake shoe.
    8.  
    9. Connect the parking brake cable to the rear shoe and then install the automatic adjusting lever, spring and E-ring. Position the rear shoe so the lower end rides in the anchor plate and the upper end is against the boot of the wheel cylinder.
    10.  
    11. Install the pin and the hold down spring. Press the retainer down over the pin and rotate the pin so the crimped edge is held by the retainer.
    12.  
    13. Place the front brake into position and install the anchor spring between the front and rear shoes. Stretch the spring enough so the front shoe will fit as the rear did. Install the hold down spring, pin and retainer to the front brake shoe.
    14.  
    15. Connect the return spring to the front brake shoe.
    16.  
    17. Check the operation of the automatic adjuster mechanism:
      1. Apply the parking brake lever and verifying the adjusting bolt turns.
      2.  
      3. Adjust the strut to where it is the shortest possible length.
      4.  
      5. Install the brake drum.
      6.  
      7. Apply the parking brake lever until the clicking sound can no longer be heard.
      8.  

    18.  
    19. Check the clearance between the brake shoes and drum:
      1. Remove the brake drum.
      2.  
      3. Measure the brake drum inside diameter and diameter of the brake shoes. The difference is "Shoe-to-drum clearance" and should be approximately 0.024 inch (0.6mm). If incorrect, check the parking brake system.
        NOTE
        A special brake caliper tool is required to gauge the brake drum inside diameter and shoe-to-drum clearance. However it is not required to perform brake shoe adjustment.

      4.  

    20.  
    21. Install the brake drum.
    22.  
    23. Adjust the brake pedal until a slight drag is felt when the drum is spun by hand.
    24.  
    25. Pull the parking lever all the way up until a clicking sound can no longer be heard. Check the clearance between brake shoes and brake drum.
    26.  
    27. Install the rear wheels, tighten the wheel lug nuts and lower the vehicle.
    28.  
    29. Retighten the wheel lug nuts and pump the brake pedal a few times before moving the vehicle. Adjust the rear brakes again if necessary.
    30.  
    31. Check the level of brake fluid in the master cylinder, then perform a test drive.
    32.  
    33. Connect the negative battery cable to the battery.
    34.  

    T-100, Tacoma
    1. Loosen the rear wheel lug nuts slightly.
    2.  
    3. Block the front wheels, raise the rear of the vehicle, and safely support it with jackstands.
    4.  
    5. Remove the wheel lug nuts and the wheel.
    6.  
    7. Remove the brake drum.
    8.  
    9. If the drum is difficult to remove, perform the following:
      1. Insert a flat prying tool through the hole in the brake drum and hold the automatic adjusting lever away from the adjuster.
      2.  
      3. Reduce the brake shoe adjustment by turning the adjuster bolt with a brake tool.
      4.  
      5. The drum should now be loose enough to remove without much effort.
      6.  

    10.  
    11. Remove the rear shoe.
      1. Carefully unhook the return spring from the brake shoe.
      2.  
      3. Remove the shoe hold-down spring, cups and the pin.
      4.  
      5. Disconnect the anchor spring from the rear shoe and remove the rear shoe.
      6.  
      7. Disconnect the anchor spring from the front shoe.
      8.  

    12.  
    13. Remove the front shoe.
      1. Remove the shoe hold-down spring, cups and pin.
      2.  
      3. Remove the return spring from the front shoe.
      4.  
      5. Remove the front shoe with the adjuster.
      6.  
      7. Disconnect the parking brake cable from the front shoe.
      8.  

    14.  

    To install:

    1. Inspect the shoes for signs of unusual wear or scoring.
    2.  
    3. Check the wheel cylinder for any sign of fluid seepage or frozen pistons.
    4.  
    5. Clean and inspect the brake backing plate and all other components. Check that the brake drum inner diameter is within specified limits. Lubricate the backing plate at the positions the brakes come in contact with the backing plate. Also lubricate the anchor plate.
    6.  
    7. Mount the automatic adjuster assembly onto a new rear brake shoe.
    8.  
    9. Install the front shoe.
      1. Install the parking brake cable to the front shoe.
      2.  
      3. Install the front shoe with the adjuster.
      4.  
      5. Install the return spring to the front shoe.
      6.  
      7. Install the shoe hold-down spring, cups and pin.
      8.  

    10.  
    11. Install the rear shoe.
      1. Install the anchor spring to the front shoe.
      2.  
      3. Install the anchor spring to the rear shoe and install the rear shoe.
      4.  
      5. Install the shoe hold-down spring, cups and the pin.
      6.  
      7. Hook the return spring to the brake shoe.
      8.  

    12.  
    13. Install the brake drum.
    14.  
    15. Adjust the brake shoes until a slight drag is felt when the drum is spun by hand.
    16.  
    17. Remove the brake drum and check the clearance between brake shoes and brake drum. Adjust the clearance to specification.
    18.  
    19. Pull the parking lever all the way up until a clicking sound can no longer be heard. Verify that the drum doesn't turn. If the drum turns, adjust the parking brake cable.
    20.  
    21. Install the rear wheels, tighten the wheel lug nuts and lower the vehicle.
    22.  
    23. Retighten the wheel lug nuts and pump the brake pedal a few times before moving the vehicle. Adjust the rear brakes again if necessary.
    24.  
    25. Check the level of brake fluid in the master cylinder, then perform a test drive.
    26.  
    27. Connect the negative battery cable to the battery.
    28.  

    T-100, Tacoma And 4Runner
    1. Loosen the rear wheel lug nuts slightly.
    2.  
    3. Block the front wheels, raise the rear of the vehicle, and safely support it with jackstands.
    4.  
    5. Remove the wheel lug nuts and the wheel.
    6.  
    7. Remove the brake drum.
    8.  
    9. If the drum is difficult to remove, perform the following:
      1. Insert a flat prying tool through the hole in the brake drum and hold the automatic adjusting lever away from the adjuster.
      2.  
      3. Reduce the brake shoe adjustment by turning the adjuster bolt with a brake tool.
      4.  
      5. The drum should now be loose enough to remove without much effort.
      6.  

    10.  
    11. Remove the rear shoe.
      1. Carefully unhook the return spring from the brake shoe.
      2.  
      3. Remove the shoe hold-down spring, cups and the pin.
      4.  
      5. Disconnect the anchor spring from the rear shoe and remove the rear shoe.
      6.  
      7. Disconnect the anchor spring from the front shoe.
      8.  

    12.  
    13. Remove the front shoe.
      1. Remove the shoe hold-down spring, cups and pin.
      2.  
      3. Remove the return spring from the front shoe.
      4.  
      5. Remove the front shoe with the adjuster.
      6.  
      7. Disconnect the parking brake cable from the front shoe.
      8.  

    14.  

    To install:

    1. Inspect the shoes for signs of unusual wear or scoring.
    2.  
    3. Check the wheel cylinder for any sign of fluid seepage or frozen pistons.
    4.  
    5. Clean and inspect the brake backing plate and all other components. Check that the brake drum inner diameter is within specified limits. Lubricate the backing plate at the positions the brakes come in contact with the backing plate. Also lubricate the anchor plate.
    6.  
    7. Mount the automatic adjuster assembly onto a new rear brake shoe.
    8.  
    9. Install the front shoe.
      1. Install the parking brake cable to the front shoe.
      2.  
      3. Install the front shoe with the adjuster.
      4.  
      5. Install the return spring to the front shoe.
      6.  
      7. Install the shoe hold-down spring, cups and pin.
      8.  

    10.  
    11. Install the rear shoe.
      1. Install the anchor spring to the front shoe.
      2.  
      3. Install the anchor spring to the rear shoe and install the rear shoe.
      4.  
      5. Install the shoe hold-down spring, cups and the pin.
      6.  
      7. Hook the return spring to the brake shoe.
      8.  

    12.  
    13. Install the brake drum.
    14.  
    15. Adjust the brake shoes until a slight drag is felt when the drum is spun by hand.
    16.  
    17. Remove the brake drum and check the clearance between brake shoes and brake drum. Adjust the clearance to specification.
    18.  
    19. Pull the parking lever all the way up until a clicking sound can no longer be heard. Verify that the drum doesn't turn. If the drum turns, adjust the parking brake cable.
    20.  
    21. Install the rear wheels, tighten the wheel lug nuts and lower the vehicle.
    22.  
    23. Retighten the wheel lug nuts and pump the brake pedal a few times before moving the vehicle. Adjust the rear brakes again if necessary.
    24.  
    25. Check the level of brake fluid in the master cylinder, then perform a test drive.
    26.  
    27. Connect the negative battery cable to the battery.
    28.  

     
    AutoZone Logo