AutoZone 2006 Volvo Truck XC90 2WD 2.5L Turbo 5cyl | Repair Guides | Emission Controls | Electronic Engine Controls | Crankshaft Position (ckp) Sensor | AutoZone.com

Search suggestions

    My Vehicles

    2006 Volvo Truck XC90 2WD 2.5L Turbo 5cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 10:00 PM today

    Save 20% Sitewide

    Use Code: YOUCHOOSE20

    See Details

    Get A $25 Gift Card

    Use Code: YOUCHOOSE25

    See Details

    VW Passat & Audi A4 1990-2000

    Crankshaft Position (CKP) sensor

    Print

    OPERATION

    The crankshaft position sensor detects gaps in the sensor ring corresponding to TDC of each cylinder. The sensor uses a permanent magnet, core and coil. The changing gap causes the magnetic field near the sensor to change. This in turn varies the voltage signal to the ECM. The ECM uses the signals for ignition timing and fuel synchronization.

    TESTING
    Audi A4 2.8L
    1. Disconnect the electrical harness connector.
    2.  
    3. Switch the DMM to its resistance range and connect it between the CKP sensor connector terminals 1 and 2 , using jumper wires from VW 1594 test kit. The DMM should show approximately 1,000 ohms.
    4.  
    5. If the specified value is not obtained, replace the crankshaft position sensor.
    6.  
    7. If the specified value is obtained, connect the DMM between terminal 1 and 3 (GND), then between terminals 2 and 3 (GND). The DMM should show infinite ohms (open).
    8.  
    9. If the specified value is not obtained, replace the crankshaft position sensor.
    10.  
    11. If the specified value is obtained, check the wiring for continuity or short between crankshaft position sensor and ECM, using a wiring diagram.
    12.  
    13. Connect a VAG 1598/19 test box to the ECM harness connector.
    14.  
    15. Check the CKP sensor shielding for continuity by connecting a DMM between terminal 3 and engine ground (GND). The DMM should show a maximum of 1 ohm.
    16.  
    17. Check the wiring for continuity between the CKP sensor connector terminal 1 and the test box socket A9 , then between the CKP sensor connector terminal 2 and test box socket A10 . There should be a maximum of 1 ohm.
    18.  
    19. If the specified values are not obtained, check and eliminate any short or open circuits in the wiring.
    20.  
    21. If the wiring is OK, replace ECM.
    22.  

    Passat 2.8L
    1. Disconnect the harness connector from the crankshaft position sensor.
    2.  
    3. Switch the DMM to its ohms range.
    4.  
    5. Connect the DMM to terminals 1 and 2 of CKP sensor harness, using adaptor leads from VW 1594 adaptor kit.
    6.  
    7. Resistance between terminals 1 and 2 must be 500-700 ohms.
    8.  
    9. Connect the DMM to terminals 1 and 2 , then 1 and 3 of the CKP sensor harness, using adaptor leads from VW 1594 adaptor kit.
    10.  
    11. The resistance must be infinite ohms.
    12.  

    REMOVAL & INSTALLATION
    1. Disconnect the electrical connector from the sensor.
    2.  
    3. Remove the crankshaft sensor retaining bolt and remove the sensor.
    4.  
    5. Replace the O-ring and lightly lubricate it with clean engine oil.
    6.  
    7. Installation is reverse of removal.
    8.  

     
    AutoZone Logo