Duralast/Pinion Seal - Front

Vehicle Specific
Part Number: 8611N
Alternate Part Number: 8611N
Product Details
Part Number: 8611N
Weight: 0.12 lbs
Shipping Information: Overnight and Two Day shipping are not available for PO Box, APO/FPO/DPO or US Territory addresses.
This product may be shipped directly by the vendor to any eligible US addresses, excluding APO/FPO/DPO or US Territory addresses.
  • Overall
     

    Please wait while we process your request
     

    Please wait while we retrieve the user's information

    Bio

    Your bio is currently empty. Now is a great time to fill in your profile.

    Rank

    This profile is private.

    This profile is only shared with friends.

    This profile is under review.

    We were unable to request friendship with this user.

    We were unable to request friendship with this user. Are you logged in?

    Your friendship request has been sent to this user.

    We were unable to terminate friendship with this user.

    We were unable to terminate friendship with this user. Are you logged in?

    You are no longer friends with this user.

    We were unable to ignore this user.

    We were unable to ignore this user. Are you logged in?

    This user is now ignored.

    We were unable to stop ignoring this user.

    We were unable to stop ignoring this user. Are you logged in?

    This user is no longer ignored.

    We encountered a problem recommending this user.

    pluck_user_recommend_permission

    You have recommended this user.

    Please limit your comment length to less than 2000 characters.

    Send Cancel

    Duralast/Pinion Seal - Rear

    Filter

    Sort by:

    1 review


    Please wait while we perform your request.

    Please wait while we perform your request.
    5

    This review is hidden because you have chosen to ignore Member 5546390. Show DetailsHide Details

    great seal at a great price!

    I bought this seal to replace the leaking rear pinion seal on my 1998 Chevy Astro.Its not a very hard job to do if you take your time and plan it out.here are a couple tips and a couple other item you will need.start by removing your drive shaft. then make sure you scribe or paint a line on the pinion yoke nut and the pinion shaft so you can reinstall the nut at the same position it was before you removed it.next you remove the nut with a 1 1/4" socket and the yoke should pull right off.you will loose about 1/2-1 quart of oil.next remove the old seal and clean the housing well with solvent.after it dries grab your new seal and put a light coat of RTV sealant around the metal edge of the seal that will mate to the pinion housing.then carefully use a small hammer to tap the seal in.then wipe some clean oil on the pinion yoke surface that the seal rides on so the sealing area isn't dry. and then you need to put some thread locker on the shaft threads and install the nut .make sure you have the washer on the shaft before the nut . then tighten it down gently until your line you scribed on the nut is lined up with the line on the shaft.it shouldnt take a whole lot of torque to tighten it down.then reinstall your drive shaft using thread locker on the u joint retainer bolts and top off your gear oil in the rear end and your done.

    so other than the seal you will also need to buy a 1 1/4" socket if you don't have one that big, RTV gasket sealant,thread locker and a quart of gear oil to complete this job

    Pros: the seal i recived was a timken brand seal

    Cons: none

    share review Share pluck_abuse_reportAlt Report

    Edited on 8/22/2015 by Editor

    Comment


    Please wait while we perform your request.
    Select reviews which match your interests.

    Please wait while we file your abuse report.

    Report Abuse

    We're sorry. We were unable to report abuse at this time.

    We limit the number of reactions an individual user can submit over a given period for quality reasons. You have currently reached that limit. Please try resubmitting your abuse report again later.

    Comment is too long. Enter 500 characters or less.

    Send Cancel

    Please wait while we send the email.

    Email This

    You may send this to 5 e-mail addresses. Please separate each address with a space.

    We're sorry, but the item you are sending has been removed from the site.

    We're sorry. We were unable to send the email at this time.

    Please specify a recipient.

    You can only send messages to 5 addresses at a time.

    The address "" is not valid.

    Please specify a subject.

    Send Cancel
    These parts DO NOT fit your selected vehicle.
    1996 Saturn SW2 1.9L MFI DOHC 4cyl
    These parts fit your vehicle(s):
    Browse to find other vehicles this part fits:

    OTHER CUSTOMERS ALSO VIEWED

    Buy With Confidence

    ABOUT CORE PARTS

    Buy online and return core parts to the store to be refunded the price.
    Core Parts Policy

    Core return policy

    FREE SHIPPING

    On Orders $75 or Greater
    and free shipping to APO, FPO, DPO addresses.
    Get More Details

    Free shipping policy

    RETURN ANYWHERE

    Buy Online, Return
    Anywhere
    Get More Details

    Return anywhere

    SAME-DAY STORE PICKUP

    Save time by buying online and picking up items in store.
    Learn More

    Same day store pickup
    PAYMENT METHODS 
     
    AutoZone Logo