Duralast Wireset 9124 - Read Reviews on Duralast #9124

Duralast Wireset

Vehicle Specific

Part Number: 9124
Features & Benefits

Duralast™ ignition wire sets allow you to complete an ignition tune-up, without breaking the bank. Changing your ignition wire set each time you change your spark plugs ensures a solid connection and a moisture tight seal to achieve maximum performance. Today s automobile manufacturers continue to introduce more compact, fuel efficient engines with smaller cylinder counts. These higher revving engines sit in ever smaller engine compartments which expose ignition wires to extreme operating temperatures. Duralast™ wire sets not only withstand the demands of these high-heat conditions but also resist exposure to chemicals, deliver maximum spark, and meet the original manufacturers functional requirements.

  • Duralast™ wire sets offer extensive coverage for vehicles on the road today
  • Performance of product meets or exceeds original equipment specifications
  • Duralast™ wire sets are designed to provide original equipment fit for your vehicle
  • Pre-greased silicone spark plug boots ensure easy installation and removal
  • Corrosion resistant terminals provide consistent performance
  • Quick-lock terminals allow for quick and easy installation
Product Details
Part Number: 9124
Weight: 0.09lbs
Boot Color: Black
Boot End Angle: 180 degrees
Boot Material: Silicone Insulated 5K ohm Resistor
Coil Wire Included: Yes
Distributor / Coil Boot Color: Black
Distributor / Coil Boot Material: Silicone Insulated 1K Ohm Resistor
Maximum Operating Temperature (°F): 356
RFI Protection: No
Vehicle Cylinders: 6
Wire Color: Black
Wire Core Material: Copper
Wire Diameter (mm): 7
Wire Insulation: EPDM
Wire Jacket Material: EPDM
Shipping Information: Overnight and Two Day shipping are not available for PO Box, APO/FPO/DPO or US Territory addresses.
  • Overall

    Please wait while we process your request

    Please wait while we retrieve the user's information


    Your bio is currently empty. Now is a great time to fill in your profile.


    This profile is private.

    This profile is only shared with friends.

    This profile is under review.

    We were unable to request friendship with this user.

    We were unable to request friendship with this user. Are you logged in?

    Your friendship request has been sent to this user.

    We were unable to terminate friendship with this user.

    We were unable to terminate friendship with this user. Are you logged in?

    You are no longer friends with this user.

    We were unable to ignore this user.

    We were unable to ignore this user. Are you logged in?

    This user is now ignored.

    We were unable to stop ignoring this user.

    We were unable to stop ignoring this user. Are you logged in?

    This user is no longer ignored.

    We encountered a problem recommending this user.


    You have recommended this user.

    Please limit your comment length to less than 2000 characters.

    Send Cancel

    Duralast Wireset


    Sort by:

    1 review

    Please wait while we perform your request.

    Please wait while we perform your request.

    This review is hidden because you have chosen to ignore Member 1016016. Show DetailsHide Details

    This wire set has a long way to go...

    This wire set was assembled incorrectly. Since it is encased in a plastic enclosure, it is designed to be bolted onto the Valve Cover and connected to the Plugs and cap. The ends meant for the plugs had the cap ends on them and the connections for the distributor cap has the spark plug ends on them. So we needed to disassemble the plastic enclosure, remove the wires and flip the wires around and then re-assemble the enclosure. Also, the set did not come with any silicone grease to apply on the boots. Finally, the Tachometer pick up connector on spark plug wire #6 was out of spec causing the OEM connector mating to not "click" into lock position. so we needed to take a small file to the capture points on the connector before we achieve a locked connection. For the price of these wires, the guys performing the assembling process should have gotten it right. After the modifications to the harness and connector, it was installed and we did notice an improvement on our BMW E30. Hesitation is minimized and sounds like it's running smoother.

    Pros: Good quality with 7mm wire

    Cons: Built incorrectly, RPM connector out of spec (will need to be filed down)

    share review Share pluck_abuse_reportAlt Report

    Please wait while we perform your request.
    Select reviews which match your interests.

    Please wait while we file your abuse report.

    Report Abuse

    We're sorry. We were unable to report abuse at this time.

    We limit the number of reactions an individual user can submit over a given period for quality reasons. You have currently reached that limit. Please try resubmitting your abuse report again later.

    Comment is too long. Enter 500 characters or less.

    Send Cancel

    Please wait while we send the email.

    Email This

    You may send this to 5 e-mail addresses. Please separate each address with a space.

    We're sorry, but the item you are sending has been removed from the site.

    We're sorry. We were unable to send the email at this time.

    Please specify a recipient.

    You can only send messages to 5 addresses at a time.

    The address "" is not valid.

    Please specify a subject.

    Send Cancel
    Browse to find other vehicles this part fits:





    Buy online and return core parts to the store to be refunded the price.
    Core Parts Policy


    On Orders $75 or Greater
    and free shipping to APO, FPO, DPO addresses.
    Get More Details


    Buy Online, Return
    Get More Details


    Save time by buying online and picking up items in store.
    Learn More

    Payment Methods: