626 1999-2001

Window Systems

Print

Diagnosis & Testing



  1. Disconnect the negative battery cable.
  2.  
  3. Raise the rear edge of the door glass about 3.5 inches from the fully lowered position.
  4.  
  5. Remove the regulator handle if equipped with a manual window.
  6.  
  7. Remove the inner garnish.
  8.  
  9. Remove the screw to remove the inner handle.
  10.  
  11. Turn over the recess cover to remove the screw.
  12.  
  13. Remove the screw.
  14.  
  15. Remove the fasteners.
  16.  
  17. Pull the front door trim to disengage clips from the body.
  18.  
  19. Pull the front door trim upward to disengage hooks B from the body.
  20.  
  21. Disconnect the trunk lid opener switch connector.
  22.  
  23. Disconnect the connector if equipped with a power window.
  24.  
  25. Disconnect the courtesy light.
  26.  
  27. Inspect for the continuity between the power window main switch terminals by using an ohmmeter.
  28.  
  29. When checking the driver-s side window switch, connect the B+ to terminal H and connect the ground to the terminal F. If the switch fails a test replace the switch.
  30.  
  31. Refer to the accompanying illustrations for terminal locations and continuity checks.

    Click image to see an enlarged view

    Fig. Front door trim-626



    Click image to see an enlarged view

    Fig. Window switch terminal locations-626



    Click image to see an enlarged view

    Fig. Window switch continuity checks-626

  32.  

Power Windows



Removal & Installation
Motor & Regulator
  1. Disconnect the negative battery cable.
  2.  
  3. Raise the rear edge of the door glass about 3.5 inches from the fully lowered position.
  4.  
  5. Remove the regulator handle if equipped with a manual window.
  6.  
  7. Remove the inner garnish.
  8.  
  9. Remove the screw to remove the inner handle.
  10.  
  11. Turn over the recess cover to remove the screw.
  12.  
  13. Remove the screw.
  14.  
  15. Remove the fasteners.
  16.  
  17. Pull the front door trim to disengage clips from the body.
  18.  
  19. Pull the front door trim upward to disengage hooks B from the body.
  20.  
  21. Disconnect the trunk lid opener switch connector.
  22.  
  23. Disconnect the connector if equipped with a power window.
  24.  
  25. Disconnect the courtesy light.
  26.  
  27. Remove the bracket and inner door handle.
  28.  
  29. Remove the front door screen and lock

    Click image to see an enlarged view

    Fig. Front door trim-626



    Click image to see an enlarged view

    Fig. Front door lock assembly-626



    Click image to see an enlarged view

    Fig. Front door glass assembly-626

  30.  
  31. Remove the lock link, outer handle and lock cylinder if needed.
  32.  
  33. Remove the screws, door glass and glass run channel.
  34.  
  35. Remove the connector, regulator retainers and regulator.
  36.  

To install:

  1. Installation is the reverse of removal.

    Click image to see an enlarged view

    Fig. Front door regulator assembly-626

  2.  

Removal & Installation



Switch
  1. Disconnect the negative battery cable.
  2.  
  3. Raise the rear edge of the door glass about 3.5 inches from the fully lowered position.
  4.  
  5. Remove the regulator handle if equipped with a manual window.
  6.  
  7. Remove the inner garnish.
  8.  
  9. Remove the screw to remove the inner handle.
  10.  
  11. Turn over the recess cover to remove the screw.
  12.  
  13. Remove the screw.
  14.  
  15. Remove the fasteners.
  16.  
  17. Pull the front door trim to disengage clips from the body.
  18.  
  19. Pull the front door trim upward to disengage hooks B from the body.
  20.  
  21. Disconnect the trunk lid opener switch connector.
  22.  
  23. Disconnect the connector if equipped with a power window.
  24.  
  25. Disconnect the courtesy light.
  26.  
  27. Remove the screw and the switch.
  28.  

To install:

  1. Installation is the reverse of removal.

    Click image to see an enlarged view

    Fig. Front door trim-626

  2.  

 
label.common.footer.alt.autozoneLogo