Acura CL Integra NSX RL RSX TL TSX 2001-2006

Side Mirrors (1 of 2)

Print

Power Mirror



Removal & Installation
2001-03 TL Models

NOTE
This procedure requires the use of Snap-On Trim pad remover, A177A or equivalent, commercially available trim pad removal tool. When removing the door panel components, be careful not to scratch the door panel.

  1. Lower the window completely.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown

  4.  
  5. Remove the inner handle (A), as follows:
    1. Pry out the cap (B), and remove the screw.
    2.  
    3. Pull the inner handle forward and out half-way.
    4.  
    5. Disconnect the inner handle rod (C), power door lock switch connector (D), and on 2002-03 models, driving position memory switch connector (E) (driver's)

      Click image to see an enlarged view

      Fig. Door inner handle (A) removal and installation-2001-03 TL models

    6.  

  6.  
  7. Remove the screw from the armrest portion of the door panel. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward, and disconnecting the power window switch connector (C). Remove the door panel with as little bending as possible to avoid creasing or breaking it.

    Click image to see an enlarged view

    Fig. Door panel removal and installation-2001-03 TL models

  8.  
  9. Disconnect the power window switch connectors (A), power mirror switch connector (B) (driver's), security indicator connector (C) (driver's), driver's door subharness connector (D), and courtesy light bulb socket (passenger's) (E), and detach the harness clips (F) from the passenger's door panel.

    Click image to see an enlarged view

    Fig. Disconnect the power window switch connectors (A), power mirror switch connector (B) (driver's), security indicator connector (C) (driver's), driver's door subharness connector (D), and courtesy light bulb socket (passenger's) (E), and detach the harness clips (F) from the passenger's door panel-2001-03 TL models

  10.  
  11. Disconnect the connector (A), and detach the harness clip (B), then remove the nuts securing the mirror.

    Click image to see an enlarged view

    Fig. Disconnect the connector (A), and detach the harness clip (B), then remove the nuts securing the mirror-2001-01 TL models

  12.  
  13. While holding the mirror, push out the clip (A), and remove the mirror (B). Do not scratch the door.

    Click image to see an enlarged view

    Fig. While holding the mirror, push out the clip (A), and remove the mirror (B)-2001-03 TL models

  14.  

To install:

  1. Install the mirror in the reverse order of removal, and note these items:
    1. Make sure the connector is plugged in properly.
    2.  
    3. Attach the harness clip.
    4.  

  2.  
  3. Installation of the door panel is the reverse of the removal procedure. Note the following:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connector is plugged in properly, and the rod is connected properly.
    4.  
    5. Check the window and power door lock operation.
    6.  

  4.  

2001-04 RL Models
  1. Raise the window fully.
  2.  
  3. Remove the trim plate, then remove the screws.
    NOTE
    Do not remove the inner handle from the door panel.

  4.  
  5. Remove the screw and stop. Use a suitable trim panel removal tool to release the clips that hold the door panel, then remove the door panel by pulling it upward.
    NOTE
    When removing the door panel, bend it as little as possible to prevent creasing or breaking it.

  6.  
  7. Disconnect the connectors and inner handle cable.
  8.  
  9. Remove the plastic cover as necessary.
  10.  
  11. Disconnect the connector, and detach the clip.
  12.  
  13. Support the mirror then, remove the mirror mounting nuts, detach the clip, and remove the mirror from the vehicle.
  14.  
  15. Installation is the reverse of the removal procedure. Make sure the mirror connector is properly attached.
  16.  

2004-06 TL Models

NOTE
This procedure requires the use of the following tools, or their equivalents: KTC trim tool set SOJATP2014 and Snap-On Trim pad remover A 177A. Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.

  1. Lower the glass fully.
  2.  
  3. Using a trim tool, push on the rear hook (A) and pivot the cover (B) on the front hook (C), then remove the cover and the screws (D) securing the inner handle (E).

    Click image to see an enlarged view

    Fig. Using a trim tool, push on the rear hook (A) and pivot the cover (B) on the front hook (C), then remove the cover and the screws (D) securing the inner handle (E)-2004-06 TL models

  4.  
  5. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it, as follows:
    1. Remove the stopper (B) and screw (C) from the door panel.
    2.  
    3. Release the clips (D) that hold the door panel with a commercially available trim pad remover.
    4.  
    5. Starting at the rear, pull the door panel upward, then release the lock knob (E).
      NOTE
      NOTE: The inner handle cable (F) is connected to the door panel. Do not pull the door panel up too far, or the inner handle cable will be damaged.



      Click image to see an enlarged view

      Fig. Door panel removal and installation-2004-06 TL models

    6.  

  6.  
  7. While holding the door panel (A) away from the door, disconnect the inner handle cable (B), driving position memory switch connector (C) (driver's door), power door lock switch connector (D), power window switch connector (E, F), harness connector (G) (driver's door), door courtesy light harness clips (H) (passenger's door), and remove the door courtesy light (I) (passenger's door ) by turning it counterclockwise one quarter turn.

    Click image to see an enlarged view

    Fig. While holding the door panel (A) away from the door, disconnect the inner handle cable (B), driving position memory switch connector (C) (driver's door), power door lock switch connector (D), power window switch connector (E, F), harness connector (G) (driver's door), door courtesy light harness clips (H) (passenger's door), and remove the door courtesy light (I) (passenger's door ) by turning it counterclockwise one quarter turn

  8.  
  9. If necessary, remove the door glass inner weatherstrip from the door panel by pulling it down.
  10.  
  11. Detach the door sash inner trim and weatherstrip mounting clips.

    Click image to see an enlarged view

    Fig. Detach the door sash inner trim and weatherstrip mounting clips-2004-06 TL models

  12.  
  13. Remove the door sash inner trim (A), as follows:
    1. Detach the clips.
    2.  
    3. While removing the lower edge of the door sash inner trim from the edge of the sash, and release the hooks (B, C), then remove the trim

      Click image to see an enlarged view

      Fig. Removing the door sash inner trim (A)-2004-06 TL models

    4.  

  14.  
  15. Detach the connector (A). Support the mirror (B), then remove the nuts (C) and remove the mirror from the vehicle.

    Click image to see an enlarged view

    Fig. Detach the connector (A). Support the mirror (B), then remove the nuts (C) and remove the mirror from the vehicle-2004-06 models

  16.  

To install:

  1. Installation of the mirror is the reverse of the removal procedure. Make sure the connector is plugged in properly.
  2.  
  3. Reinstall new door outer molding in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Push the clips into place securely.
    4.  

  4.  
  5. Install the door panel in the reverse order of removal, and note these items:
    1. Check for damaged or stress-whitened clips, and replace them with new ones.
    2.  
    3. Make sure the connectors are plugged in properly, and the cable is connected properly.
    4.  
    5. Make sure the window and power door lock operate properly.
      NOTE
      The power window control unit must be reset, using one of the below listed methods: Using the HDS or Without an HDS.

    6.  

  6.  
  7. Reset the power window control until on the door that was removed, using an HDS, as follows:
    1. Connect the Honda Diagnostic System (HDS) to the vehicle's DLC.
    2.  
    3. Turn the ignition switch ON (II), then enter the vehicle's VIN and mileage at the prompts.
    4.  
    5. Select ''Body Electrical'' from the ''System Selection'' menu.
    6.  
    7. From the ''Body Electrical System Select'' menu, select ''Power Windows''.
    8.  
    9. From the ''Mode'' menu, select ''Adjustment''.
    10.  
    11. From the ''Adjustment'' menu, select ''Window P Reset'' for driver's side (passenger's side) window.
    12.  
    13. Follow the prompts on the screen.
    14.  
    15. Confirm that the power window control unit is reset by using the driver's (passenger's) window AUTO UP and AUTO DOWN function.
    16.  

  8.  
  9. If you do not have access to an HDS, reset the power window control until on the door that was removed, as follows:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's (passenger's) window all the way down by using the driver's (passenger's) window DOWN switch.
    4.  
    5. Open the driver's (passenger's) door.
      NOTE
      Steps d.-g. must be done within 5 seconds of each other.

    6.  
    7. Turn the ignition switch OFF.
    8.  
    9. Push and hold the driver's (passenger's) window DOWN switch.
    10.  
    11. Turn the ignition switch ON (II).
    12.  
    13. Release the driver's (passenger's) window DOWN switch.
    14.  
    15. Repeat steps d.-g. three more times.
    16.  
    17. Wait 1 second.
    18.  
    19. Confirm that AUTO UP and AUTO DOWN do not work. If AUTO UP and DOWN work, go back to step a.
    20.  
    21. Move the driver's (passenger's) window all the way down by using the driver's (passenger's) window DOWN switch.
    22.  
    23. Pull up and hold the driver's (passenger's) window UP switch until the window reaches the fully closed position, then continue to hold the switch for 1 second.
    24.  
    25. Confirm that the power window control unit is reset by using the driver's (passenger's) window AUTO UP and AUTO DOWN function.
    26.  
    27. If the window still does not work in AUTO, repeat the procedure several times, paying close attention to the 5 second time limit between steps.
    28.  

  10.  

2005-06 RL Models

NOTE
This procedure requires the following special tools, or their equivalents: KTC trim tool set SOJATP2014 and Snap-On Trim pad remover, Snap-on A 177A.


NOTE
Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.

  1. Lower the window fully.
  2.  
  3. Using a trim tool, push on the bottom hook (A) and pivot the cover (B) on the upper hooks (C), then detach the front hook (D), and then remove the cover and the screw securing the inner handle (E).

    Click image to see an enlarged view

    Fig. Using a trim tool, push on the bottom hook (A) and pivot the cover (B) on the upper hooks (C), then detach the front hook (D), and then remove the cover and the screw securing the inner handle (E)-2005-06 RL models

  4.  
  5. Using a trim tool, pull the top edge of the pocket light cover (A) out to release the hooks (B), and release the hooks (C, D), then remove the cover, and then remove the screw.

    Click image to see an enlarged view

    Fig. Using a trim tool, pull the top edge of the pocket light cover (A) out to release the hooks (B), and release the hooks (C, D), then remove the cover, and then remove the screw-2005-06 RL models

  6.  
  7. Using a trim tool, pry out the notch (A) of the grip cover (B) to detach the hook (C), and then pull out the cover to release the remaining hooks (D), then remove the cover from the grip (E).

    Click image to see an enlarged view

    Fig. Using a trim tool, pry out the notch (A) of the grip cover (B) to detach the hook (C), and then pull out the cover to release the remaining hooks (D), then remove the cover from the grip (E)-2005-06 RL models

  8.  
  9. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it, as follows:
    1. Release the clips (B, C) that hold the door panel with a commercially available trim pad remover.
    2.  
    3. While holding the door panel away from the door, disconnect the door subharness connector (D) and the power mirror connector (E).
    4.  
    5. While holding the door panel away from the door, remove the screws (F), then remove the inner handle (G) from the door panel.
      NOTE
      The inner handle cable (H) and the lock cable (I) are connected to the door panel. Do not pull the door panel up too far, or the inner handle cable will be damaged.

    6.  

  10.  
  11. Replace all of the door panel clips with new ones

    Click image to see an enlarged view

    Fig. Door panel removal and installation-2005-06 RL models

  12.  
  13. Remove the plastic cover.
  14.  
  15. Remove the door sash outer trim, as follows:
    1. Pull back the door weatherstrip (B), then remove the upper screw (C).
    2.  
    3. Pull back the door weatherstrip, then loosen the middle and bottom screws (D, E).
    4.  
    5. Lower the trim, and then release the middle and bottom screws from the holes (F) in the door.
    6.  
    7. Pull the trim up to release the hook (G) from the door. Take care not to damage the door glass outer weatherstrip (H).

      Click image to see an enlarged view

      Fig. Door sash outer trim removal and installation-2005-06 RL models

    8.  

  16.  
  17. While holding the mirror (A), remove the nuts, then remove the mirror.

    Click image to see an enlarged view

    Fig. Side mirror (A) removal and installation-2005-06 RL models

  18.  

To install:

  1. Install the mirror and secure with the retaining nuts. Tighten the nuts to 6 ft. lbs. (8 Nm).
  2.  
  3. Install the door sash outer trim in the reverse order of removal, and make sure the glass run channel (I) is installed in the door sash securely.
  4.  
  5. Install the door panel in the reverse order of removal, and note these items:
    1. Make sure the connectors are plugged in properly, and the cable is connected properly.
    2.  
    3. Make sure the window and power door lock operate properly.
    4.  

  6.  
  7. Reset the power window control unit using the HDS.
    1. Check for water leaks.
    2.  
    3. Test-drive and check for wind noise and rattles.
    4.  

  8.  

CL Models

NOTE
This procedure requires the use of Trim pad remover, Snap-on A177A or equivalent, commercially available trim pad removal tool. When removing the components, be careful not to scratch the door panel.

  1. Remove the mirror mount cover, as follows:
    1. Lower the door glass fully.
    2.  
    3. Carefully detach the clips (A) and release the hooks (B), then pry out the mirror mount cover (C) by hand. Disconnect the door tweeter connector (D).

      Click image to see an enlarged view

      Fig. Mirror mount and mirror removal and installation-CL models

    4.  

  2.  
  3. Remove the inner handle (A), as follows:
    1. Pry out the cap (B), and remove the screw.
    2.  
    3. Pull the inner handle forward and out half-way.
    4.  
    5. Disconnect the inner handle rod (C) and power door lock switch connector (D). On driver's side, disconnect the driving position memory switch connector (E).

      Click image to see an enlarged view

      Fig. Inner handle (A) removal and installation-CL models

    6.  

  4.  
  5. Remove the screw from the armrest portion of the door panel. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it.

    Click image to see an enlarged view

    Fig. Door panel removal and installation

  6.  
  7. Disconnect the power window switch connector (A), power window main switch connector (B), power mirror switch connector (C) (driver's), security indicator connector (D) (driver's), driver's door sub harness connector (E), and courtesy light bulb socket (passenger's) (F).

    Click image to see an enlarged view

    Fig. Disconnect the power window switch connector (A), power window main switch connector (B), power mirror switch connector (C) (driver's), security indicator connector (D) (driver's), driver's door sub harness connector (E), and courtesy light bulb socket (passenger's) (F)-CL models

  8.  
  9. Disconnect the connectors (F), and remove the nuts (G) securing the mirror (H).
  10.  
  11. While holding the mirror, squeeze and push out the clip (I), and remove the mirror. Take care not to scratch the door.
  12.  

To install:

  1. Install the mirror in the reverse order of removal, and note the following:
    1. Replace any damaged clips with new ones.
    2.  
    3. Make sure the connectors are plugged in properly.
    4.  

  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors and courtesy light bulb socket are plugged in properly, and the rod is connected properly.
    4.  
    5. Check the window and power door lock operation
    6.  

  4.  

Integra Models
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the inner mirror control knob (if manual remote) and remove the inner delta cover from the mirror mount.
  4.  
  5. Remove the screws holding the armrest and remove the armrest. The armrest screws may be concealed behind plastic caps which must be popped out with a non-marring tool.
  6.  
  7. Remove the surround or cover for the inside door handle. Again, find the hidden screw; remove it and slide the cover off over the handle.
  8.  
  9. If not equipped with electric windows, remove the window crank handle. This can be tricky, but not difficult. Install a piece of tape on the door pad to show the position of the handle before removal. The handle is held onto the crank axle with a spring clip shaped like the Greek letter Omega. The clip is located between the back of the crank handle and the door pad. It is correctly installed with the legs pointing away from the length of the crank handle. There are three common ways of removing the clip:
  10.  
  11. Use a door handle removal tool. This inexpensive slotted and toothed tool can be fitted between the crank handle and the door panel, and is used to push the spring clip free.
  12.  
  13. Use a rag or piece of cloth and work it back and forth between the crank handle and door panel. If constant upward tension is kept, the clip will be forced free. Keep watch on the clip as it pops out; it may get lost.
  14.  
  15. Straighten a common paper clip and bend a very small J-hook at the end of it. Work the hook down from the top of the crank and engage the loop of the spring clip. As you pull the clip free, keep your other hand over the area. If this is not done, the clip will vanish to an undisclosed location, never to be seen again.
  16.  
  17. In general, power door lock and window switches mounted on the door pad (not the armrest) may remain in place until the pad is removed. Some cannot be removed until the door panel is off the door.

    Click image to see an enlarged view

    Fig. Typical door panel removal and retainer location-Integra

  18.  
  19. If the car has manual vertical door locks, remove the lock knob by unscrewing it. If this is impossible (because they're in square housings) wait until the panel is lifted free.
  20.  
  21. Using a broad, flat-bladed tool (not a screwdriver) begin gently prying the door pad away from the door. You are releasing plastic inserts from plastic seats. There will be 6 to 12 of them around the door. With care, the plastic inserts can be reused several times.
  22.  
  23. When all the clips are loose, lift up on the panel to release the lip at the top of the door. This may require a bit of jiggling to loosen the panel; do so gently and don't damage the panel. The upper edge (at the window sill) is attached by a series of retaining clips.
  24.  
  25. Once the panel is free, keep it close to the door and check behind it. Disconnect any wiring for switches, lights or speakers which may be attached.
    NOTE
    Behind the panel is a plastic sheet, taped or glued to the door. This is a water shield and must be intact to prevent water entry into the car. It must be securely attached at its edges and not be ripped or damaged. Small holes or tears can be patched with waterproof tape applied to both sides of the liner.

  26.  
  27. Remove the screw cover and the retaining screw for the mirror cover.
  28.  
  29. Unplug the connector for the power mirror.
  30.  
  31. Unfasten the three mirror retaining screws, then remove the mirror.

    Click image to see an enlarged view

    Fig. Remove the interior mirror trim



    Click image to see an enlarged view

    Fig. Squeeze the connector harness to release the wiring from the mirror assembly

  32.  

To install:

  1. Place the mirror into position and install the retaining screws.
  2.  
  3. Attach the connector for the power mirror.
  4.  
  5. Install the mirror cover, retaining screw, and screw cover.
  6.  
  7. When reinstalling, connect any wiring harnesses and align the upper edge of the panel along the top of the door first. Make sure the left-right alignment is correct; tap the top of the panel into place with the heel of your hand.
  8.  
  9. Make sure the plastic clips align with their holes; pop each retainer into place with gentle pressure.
  10.  
  11. Install the armrest and door handle bezel, remembering to install any caps or covers over the screws.
  12.  
  13. Install the window crank handle on vehicles with manual windows. Place the spring clip into the slot on the handle, remembering that the legs should point away from the long dimension of the handle. Align the handle with the tape mark made earlier and put the crank over the end of the axle. Use the heel of your hand to give the center of the crank a short, sharp blow. This will cause the crank to move inward and the spring will engage its locking groove. The secret to this trick is to push the crank straight on; if it's crooked, it won't engage and you may end up looking for the spring clip.
  14.  
  15. Install any remaining parts or trim pieces which may have been removed earlier. (Map pockets, speaker grilles, etc.)
  16.  
  17. Install the delta cover and the remote mirror handle if they were removed.
  18.  
  19. Connect the negative battery cable.
  20.  

NSX Models
  1. Lower the glass fully.
  2.  
  3. Carefully pry out the trim plate with a flat tip screwdriver as shown.
    WARNING
    To prevent damage to the trim plate, wrap the end of the screwdriver with a shop towel.

  4.  
  5. Remove the trim plate by pulling it backward, and remove the mounting screws.
  6.  
  7. Disconnect the connector and handle cable, then remove the inner handle by pulling it forward.
    NOTE
    Take care not to bend the handle cable.

  8.  
  9. Carefully remove the front and rear sash covers.
    NOTE
    Take care not to scratch the sash covers.

  10.  
  11. Remove the mounting screws. Lift the door panel straight up off the sill.
  12.  
  13. Disconnect the connectors from the following:

    Trunk lid opener
     
    Power window/Door mirror
     
    Courtesy light
     
    Security alarm
     

  14.  
  15. Remove the switch panel and air duct from the door panel as required.
  16.  
  17. Remove the mounting screws and disconnect the connectors, then remove the power window control unit and speaker unit.
  18.  
  19. Remove the lower door weatherstrip retaining clips, then pull off the lower door weatherstrip.
  20.  
  21. Remove the screw grommets, and carefully remove the plastic cover.
  22.  
  23. Disconnect the mirror electrical connector.
  24.  
  25. Remove the two mounting nuts while holding the mirror, then remove the mirror.
  26.  

To install:

  1. Install the mirror, secure with the mounting nuts, then attach the electrical connector.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors and courtesy light bulb socket are plugged in properly, and the rod is connected properly.
    4.  
    5. Check the window and power door lock operation
    6.  

  4.  

RSX Models

NOTE
This procedure requires the use of the following special tools, or their equivalents: Trim pad remover, Snap-on A 177A and KTC trim tool set SOJATP2014. Use the proper tool from the KTC trim tool set to avoid damage when prying components.


WARNING
When removing the door panel components, be careful not to scratch the door panel.

  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown-RSX models

  4.  
  5. Remove the inner handle (A), as follows:
    1. Pry out on the bottom portion of the cover (B) to release the clip (C) and tabs (D), then remove the cover.
    2.  
    3. Remove the screws.
    4.  
    5. Pull the inner handle out to release the hook (E).
    6.  
    7. Pull the inner handle forward and out half-way to release the hook (F).
    8.  
    9. Disconnect the inner handle cable (G) and power door lock switch connector (H).

      Click image to see an enlarged view

      Fig. Removing the inner door handle (A)-RSX models

    10.  

  6.  
  7. Remove the screws from the armrest portion and inner handle opening.
  8.  
  9. Remove the window switch control panel (A), as follows:
    1. Pry out the front portion of the panel to release the clips.
    2.  
    3. Release the hooks (B) by pulling the panel forward.
    4.  
    5. Disconnect the power window switch connector (C).

      Click image to see an enlarged view

      Fig. Removing the window switch control panel-RSX models

    6.  

  10.  
  11. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward to release it from the lock knob (C) and door. Remove the door panel with as little bending as possible to avoid creasing or breaking it. Detach the harness clip (D) from the door panel.

    Click image to see an enlarged view

    Fig. Door panel removal and installation-RSX models

  12.  
  13. Disconnect the connector (A). While holding the mirror (B), remove the nuts, then remove the mirror. Take care not to scratch the door.

    Click image to see an enlarged view

    Fig. Disconnect the connector (A). While holding the mirror (B), remove the nuts, then remove the mirror-RSX models

  14.  

To install:

  1. Install the mirror in the reverse order of removal, and make sure the connector is plugged in properly.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged or stress-whitened clips.
    2.  
    3. Make sure the connectors are plugged in properly, and the cable is connected properly.
    4.  
    5. Push the clips into place securely.
    6.  

  4.  
  5. Do the power window control unit reset procedure, as follows:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's window all the way down holding the driver's switch in the AUTO DOWN position; when the window reaches the bottom, hold the driver's window switch in the AUTO DOWN position for 2 seconds.
    4.  
    5. Move the driver's window all the way up holding the driver's switch in the AUTO UP position; when the window reaches the top, hold the driver's window switch in the UP position for 2 seconds.
    6.  
    7. If the window does not work in AUTO, repeat step a. through c.
    8.  

  6.  
  7. Check the window and power door lock operations.
  8.  

 
label.common.footer.alt.autozoneLogo