Acura CL Integra NSX RL RSX TL TSX 2001-2006

Power Door Locks (2 of 2)

Print

Door Lock Motor



Removal & Installation
CL Models

NOTE
This procedure requires the use of Trim pad remover, Snap-on A177A or equivalent, commercially available trim pad removal tool. When removing the components, be careful not to scratch the door panel.

  1. Remove the mirror mount cover, as follows:
    1. Lower the door glass fully.
    2.  
    3. Carefully detach the clips (A) and release the hooks (B), then pry out the mirror mount cover (C) by hand. Disconnect the door tweeter connector (D).

      Click image to see an enlarged view

      Fig. Carefully detach the clips (A) and release the hooks (B), then pry out the mirror mount cover (C) by hand. Disconnect the door tweeter connector (D)-CL models

    4.  

  2.  
  3. Remove the inner handle (A), as follows:
    1. Pry out the cap (B), and remove the screw.
    2.  
    3. Pull the inner handle forward and out half-way.
    4.  
    5. Disconnect the inner handle rod (C) and power door lock switch connector (D). On driver's side, disconnect the driving position memory switch connector (E).

      Click image to see an enlarged view

      Fig. Inner handle (A) removal and installation-CL models

    6.  

  4.  
  5. Remove the screw from the armrest portion of the door panel. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it.

    Click image to see an enlarged view

    Fig. Door panel removal and installation

  6.  
  7. Disconnect the power window switch connector (A), power window main switch connector (B), power mirror switch connector (C) (driver's), security indicator connector (D) (driver's), driver's door sub harness connector (E), and courtesy light bulb socket (passenger's) (F).

    Click image to see an enlarged view

    Fig. Disconnect the power window switch connector (A), power window main switch connector (B), power mirror switch connector (C) (driver's), security indicator connector (D) (driver's), driver's door sub harness connector (E), and courtesy light bulb socket (passenger's) (F)-CL models

  8.  
  9. Detach the connector, then remove the door lock actuator.
  10.  

To install:

  1. Install the door lock actuator and attach the connector.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors and courtesy light bulb socket are plugged in properly, and the rod is connected properly.
    4.  
    5. Check the window and power door lock operation
    6.  

  4.  


NOTE
This procedure requires the use of Trim pad remover, Snap-on A177A or equivalent, commercially available trim pad removal tool. When removing the components, be careful not to scratch the door panel.

  1. Remove the mirror mount cover, as follows:
    1. Lower the door glass fully.
    2.  
    3. Carefully detach the clips (A) and release the hooks (B), then pry out the mirror mount cover (C) by hand. Disconnect the door tweeter connector (D).

      Click image to see an enlarged view

      Fig. Carefully detach the clips (A) and release the hooks (B), then pry out the mirror mount cover (C) by hand. Disconnect the door tweeter connector (D)-CL models

    4.  

  2.  
  3. Remove the inner handle (A), as follows:
    1. Pry out the cap (B), and remove the screw.
    2.  
    3. Pull the inner handle forward and out half-way.
    4.  
    5. Disconnect the inner handle rod (C) and power door lock switch connector (D). On driver's side, disconnect the driving position memory switch connector (E).

      Click image to see an enlarged view

      Fig. Inner handle (A) removal and installation-CL models

    6.  

  4.  
  5. Remove the screw from the armrest portion of the door panel. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it.

    Click image to see an enlarged view

    Fig. Door panel removal and installation

  6.  
  7. Disconnect the power window switch connector (A), power window main switch connector (B), power mirror switch connector (C) (driver's), security indicator connector (D) (driver's), driver's door sub harness connector (E), and courtesy light bulb socket (passenger's) (F).

    Click image to see an enlarged view

    Fig. Disconnect the power window switch connector (A), power window main switch connector (B), power mirror switch connector (C) (driver's), security indicator connector (D) (driver's), driver's door sub harness connector (E), and courtesy light bulb socket (passenger's) (F)-CL models

  8.  
  9. Remove the retaining screws, then remove the door lock switch.
  10.  

To install:

  1. Install the door lock switch and secure with the retaining screws.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors and courtesy light bulb socket are plugged in properly, and the rod is connected properly.
    4.  
    5. Check the window and power door lock operation
    6.  

  4.  

Integra Models
  1. Remove the inner mirror control knob (if manual remote) and remove the inner delta cover from the mirror mount.
  2.  
  3. Remove the screws holding the armrest and remove the armrest. The armrest screws may be concealed behind plastic caps which must be popped out with a non-marring tool.
  4.  
  5. Remove the surround or cover for the inside door handle. Again, find the hidden screw; remove it and slide the cover off over the handle.
  6.  
  7. If not equipped with electric windows, remove the window crank handle. This can be tricky, but not difficult. Install a piece of tape on the door pad to show the position of the handle before removal. The handle is held onto the crank axle with a spring clip shaped like the Greek letter Omega. The clip is located between the back of the crank handle and the door pad. It is correctly installed with the legs pointing away from the length of the crank handle. There are three common ways of removing the clip:
  8.  
  9. Use a door handle removal tool. This inexpensive slotted and toothed tool can be fitted between the crank handle and the door panel, and is used to push the spring clip free.
  10.  
  11. Use a rag or piece of cloth and work it back and forth between the crank handle and door panel. If constant upward tension is kept, the clip will be forced free. Keep watch on the clip as it pops out; it may get lost.
  12.  
  13. Straighten a common paper clip and bend a very small J-hook at the end of it. Work the hook down from the top of the crank and engage the loop of the spring clip. As you pull the clip free, keep your other hand over the area. If this is not done, the clip will vanish to an undisclosed location, never to be seen again.
  14.  
  15. In general, power door lock and window switches mounted on the door pad (not the armrest) may remain in place until the pad is removed. Some cannot be removed until the door panel is off the door.

    Click image to see an enlarged view

    Fig. Typical door panel removal and retainer location-Integra

  16.  
  17. If the car has manual vertical door locks, remove the lock knob by unscrewing it. If this is impossible (because they're in square housings) wait until the panel is lifted free.
  18.  
  19. Using a broad, flat-bladed tool (not a screwdriver) begin gently prying the door pad away from the door. You are releasing plastic inserts from plastic seats. There will be 6 to 12 of them around the door. With care, the plastic inserts can be reused several times.
  20.  
  21. When all the clips are loose, lift up on the panel to release the lip at the top of the door. This may require a bit of jiggling to loosen the panel; do so gently and don't damage the panel. The upper edge (at the window sill) is attached by a series of retaining clips.
  22.  
  23. Once the panel is free, keep it close to the door and check behind it. Disconnect any wiring for switches, lights or speakers which may be attached.
    NOTE
    Behind the panel is a plastic sheet, taped or glued to the door. This is a water shield and must be intact to prevent water entry into the car. It must be securely attached at its edges and not be ripped or damaged. Small holes or tears can be patched with waterproof tape applied to both sides of the liner.

  24.  
  25. Detach the wiring harness from the door lock actuator.
  26.  
  27. Remove the fasteners and then remove the door lock actuator.
  28.  

To install:

  1. Install the door lock actuator, secure with the retainers, then attach the connector.
  2.  
  3. When reinstalling, connect any wiring harnesses and align the upper edge of the panel along the top of the door first. Make sure the left-right alignment is correct; tap the top of the panel into place with the heel of your hand.
  4.  
  5. Make sure the plastic clips align with their holes; pop each retainer into place with gentle pressure.
  6.  
  7. Install the armrest and door handle bezel, remembering to install any caps or covers over the screws.
  8.  
  9. Install the window crank handle on vehicles with manual windows. Place the spring clip into the slot on the handle, remembering that the legs should point away from the long dimension of the handle. Align the handle with the tape mark made earlier and put the crank over the end of the axle. Use the heel of your hand to give the center of the crank a short, sharp blow. This will cause the crank to move inward and the spring will engage its locking groove. The secret to this trick is to push the crank straight on; if it's crooked, it won't engage and you may end up looking for the spring clip.
  10.  
  11. Install any remaining parts or trim pieces which may have been removed earlier. (Map pockets, speaker grilles, etc.)
  12.  
  13. Install the delta cover and the remote mirror handle if they were removed.
  14.  

  1. Remove the inner mirror control knob (if manual remote) and remove the inner delta cover from the mirror mount.
  2.  
  3. Remove the screws holding the armrest and remove the armrest. The armrest screws may be concealed behind plastic caps which must be popped out with a non-marring tool.
  4.  
  5. Remove the surround or cover for the inside door handle. Again, find the hidden screw; remove it and slide the cover off over the handle.
  6.  
  7. If not equipped with electric windows, remove the window crank handle. This can be tricky, but not difficult. Install a piece of tape on the door pad to show the position of the handle before removal. The handle is held onto the crank axle with a spring clip shaped like the Greek letter Omega. The clip is located between the back of the crank handle and the door pad. It is correctly installed with the legs pointing away from the length of the crank handle. There are three common ways of removing the clip:
  8.  
  9. Use a door handle removal tool. This inexpensive slotted and toothed tool can be fitted between the crank handle and the door panel, and is used to push the spring clip free.
  10.  
  11. Use a rag or piece of cloth and work it back and forth between the crank handle and door panel. If constant upward tension is kept, the clip will be forced free. Keep watch on the clip as it pops out; it may get lost.
  12.  
  13. Straighten a common paper clip and bend a very small J-hook at the end of it. Work the hook down from the top of the crank and engage the loop of the spring clip. As you pull the clip free, keep your other hand over the area. If this is not done, the clip will vanish to an undisclosed location, never to be seen again.
  14.  
  15. In general, power door lock and window switches mounted on the door pad (not the armrest) may remain in place until the pad is removed. Some cannot be removed until the door panel is off the door.

    Click image to see an enlarged view

    Fig. Typical door panel removal and retainer location-Integra

  16.  
  17. If the car has manual vertical door locks, remove the lock knob by unscrewing it. If this is impossible (because they're in square housings) wait until the panel is lifted free.
  18.  
  19. Using a broad, flat-bladed tool (not a screwdriver) begin gently prying the door pad away from the door. You are releasing plastic inserts from plastic seats. There will be 6 to 12 of them around the door. With care, the plastic inserts can be reused several times.
  20.  
  21. When all the clips are loose, lift up on the panel to release the lip at the top of the door. This may require a bit of jiggling to loosen the panel; do so gently and don't damage the panel. The upper edge (at the window sill) is attached by a series of retaining clips.
  22.  
  23. Once the panel is free, keep it close to the door and check behind it. Disconnect any wiring for switches, lights or speakers which may be attached.
    NOTE
    Behind the panel is a plastic sheet, taped or glued to the door. This is a water shield and must be intact to prevent water entry into the car. It must be securely attached at its edges and not be ripped or damaged. Small holes or tears can be patched with waterproof tape applied to both sides of the liner.

  24.  
  25. Detach the wiring harness from the door lock actuator.
  26.  
  27. Remove the fasteners and then remove the door lock actuator.
  28.  

To install:

  1. Install the door lock actuator, secure with the retainers, then attach the connector.
  2.  
  3. When reinstalling, connect any wiring harnesses and align the upper edge of the panel along the top of the door first. Make sure the left-right alignment is correct; tap the top of the panel into place with the heel of your hand.
  4.  
  5. Make sure the plastic clips align with their holes; pop each retainer into place with gentle pressure.
  6.  
  7. Install the armrest and door handle bezel, remembering to install any caps or covers over the screws.
  8.  
  9. Install the window crank handle on vehicles with manual windows. Place the spring clip into the slot on the handle, remembering that the legs should point away from the long dimension of the handle. Align the handle with the tape mark made earlier and put the crank over the end of the axle. Use the heel of your hand to give the center of the crank a short, sharp blow. This will cause the crank to move inward and the spring will engage its locking groove. The secret to this trick is to push the crank straight on; if it's crooked, it won't engage and you may end up looking for the spring clip.
  10.  
  11. Install any remaining parts or trim pieces which may have been removed earlier. (Map pockets, speaker grilles, etc.)
  12.  
  13. Install the delta cover and the remote mirror handle if they were removed.
  14.  

NSX Models
  1. Lower the glass fully.
  2.  
  3. Carefully pry out the trim plate with a flat tip screwdriver as shown.
    WARNING
    To prevent damage to the trim plate, wrap the end of the screwdriver with a shop towel.

  4.  
  5. Remove the trim plate by pulling it backward, and remove the mounting screws.
  6.  
  7. Disconnect the connector and handle cable, then remove the inner handle by pulling it forward.
    NOTE
    Take care not to bend the handle cable.

  8.  
  9. Carefully remove the front and rear sash covers.
    NOTE
    Take care not to scratch the sash covers.

  10.  
  11. Remove the mounting screws. Lift the door panel straight up off the sill.
  12.  
  13. Disconnect the connectors from the following:

    Trunk lid opener
     
    Power window/Door mirror
     
    Courtesy light
     
    Security alarm
     

  14.  
  15. Remove the switch panel and air duct from the door panel as required.
  16.  
  17. Remove the mounting screws and disconnect the connectors, then remove the power window control unit and speaker unit.
  18.  
  19. Remove the lower door weatherstrip retaining clips, then pull off the lower door weatherstrip.
  20.  
  21. Remove the screw grommets, and carefully remove the plastic cover.
  22.  
  23. Detach the connector, then remove the door lock actuator.
  24.  

To install:

  1. Install the door lock actuator and attach the connector.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors and courtesy light bulb socket are plugged in properly, and the rod is connected properly.
    4.  
    5. Check the window and power door lock operation
    6.  

  4.  

  1. Remove the door grip.
  2.  
  3. Remove he door lock switch and detach the electrical connector.
  4.  
  5. Installation is the reverse of the removal procedure.
  6.  

RSX Models

NOTE
This procedure requires the use of the following special tools, or their equivalents: Trim pad remover, Snap-on A 177A and KTC trim tool set SOJATP2014. Use the proper tool from the KTC trim tool set to avoid damage when prying components.


WARNING
When removing the door panel components, be careful not to scratch the door panel.

  1. Remove the inner handle (A), as follows:
    1. Pry out on the bottom portion of the cover (B) to release the clip (C) and tabs (D), then remove the cover.
    2.  
    3. Remove the screws.
    4.  
    5. Pull the inner handle out to release the hook (E).
    6.  
    7. Pull the inner handle forward and out half-way to release the hook (F).
    8.  
    9. Disconnect the inner handle cable (G) and power door lock switch connector (H).

      Click image to see an enlarged view

      Fig. Removing the inner door handle (A)-RSX models

    10.  

  2.  
  3. Lower the glass fully.
  4.  
  5. Remove the screws from the armrest portion and inner handle opening.
  6.  
  7. Remove the window switch control panel (A), as follows:
    1. Pry out the front portion of the panel to release the clips.
    2.  
    3. Release the hooks (B) by pulling the panel forward.
    4.  
    5. Disconnect the power window switch connector (C).

      Click image to see an enlarged view

      Fig. Removing the window switch control panel-RSX models

    6.  

  8.  
  9. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown-RSX models

  10.  
  11. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward to release it from the lock knob (C) and door. Remove the door panel with as little bending as possible to avoid creasing or breaking it. Detach the harness clip (D) from the door panel.

    Click image to see an enlarged view

    Fig. Door panel removal and installation-RSX models

  12.  
  13. Detach the electrical connector, remove the retainers, then remove the door lock actuator.
  14.  

To install:

  1. Install the door lock actuator and retaining screws, then attach the electrical connector.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged or stress-whitened clips.
    2.  
    3. Make sure the connectors are plugged in properly, and the cable is connected properly.
    4.  
    5. Push the clips into place securely.
    6.  

  4.  
  5. Do the power window control unit reset procedure, as follows:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's window all the way down holding the driver's switch in the AUTO DOWN position; when the window reaches the bottom, hold the driver's window switch in the AUTO DOWN position for 2 seconds.
    4.  
    5. Move the driver's window all the way up holding the driver's switch in the AUTO UP position; when the window reaches the top, hold the driver's window switch in the UP position for 2 seconds.
    6.  
    7. If the window does not work in AUTO, repeat step a. through c.
    8.  

  6.  
  7. Check the window and power door lock operations.
  8.  


NOTE
This procedure requires the use of the following special tools, or their equivalents: Trim pad remover, Snap-on A 177A and KTC trim tool set SOJATP2014. Use the proper tool from the KTC trim tool set to avoid damage when prying components.


WARNING
When removing the door panel components, be careful not to scratch the door panel.

  1. Remove the inner handle (A), as follows:
    1. Pry out on the bottom portion of the cover (B) to release the clip (C) and tabs (D), then remove the cover.
    2.  
    3. Remove the screws.
    4.  
    5. Pull the inner handle out to release the hook (E).
    6.  
    7. Pull the inner handle forward and out half-way to release the hook (F).
    8.  
    9. Disconnect the inner handle cable (G) and power door lock switch connector (H).

      Click image to see an enlarged view

      Fig. Removing the inner door handle (A)-RSX models

    10.  

  2.  
  3. Lower the glass fully.
  4.  
  5. Remove the screws from the armrest portion and inner handle opening.
  6.  
  7. Remove the window switch control panel (A), as follows:
    1. Pry out the front portion of the panel to release the clips.
    2.  
    3. Release the hooks (B) by pulling the panel forward.
    4.  
    5. Disconnect the power window switch connector (C).

      Click image to see an enlarged view

      Fig. Removing the window switch control panel-RSX models

    6.  

  8.  
  9. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown-RSX models

  10.  
  11. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward to release it from the lock knob (C) and door. Remove the door panel with as little bending as possible to avoid creasing or breaking it. Detach the harness clip (D) from the door panel.

    Click image to see an enlarged view

    Fig. Door panel removal and installation-RSX models

  12.  
  13. Remove the two mounting screws and the door lock switch.
  14.  

To install:

  1. Install the door lock switch and retaining screws.
  2.  
  3. Install the door panel in the reverse order of removal, and note the following:
    1. Replace any damaged or stress-whitened clips.
    2.  
    3. Make sure the connectors are plugged in properly, and the cable is connected properly.
    4.  
    5. Push the clips into place securely.
    6.  

  4.  
  5. Do the power window control unit reset procedure, as follows:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's window all the way down holding the driver's switch in the AUTO DOWN position; when the window reaches the bottom, hold the driver's window switch in the AUTO DOWN position for 2 seconds.
    4.  
    5. Move the driver's window all the way up holding the driver's switch in the AUTO UP position; when the window reaches the top, hold the driver's window switch in the UP position for 2 seconds.
    6.  
    7. If the window does not work in AUTO, repeat step a. through c.
    8.  

  6.  
  7. Check the window and power door lock operations.
  8.  

TSX Models

NOTE
This procedure requires the use of KTC trim tool set SOJATP2014 and Trim pad remover, Snap-on A 177A or equivalent, commercially available, or equivalent trim tools. Make sure to use the appropriate tool from the KTC trim tool set to avoid damage when prying components.

  1. Lower the glass fully.
  2.  
  3. Using a trim tool, pry out on the rear portion of the cover (A) to release the hooks (B, C), then remove the cover and the screws securing the inner handle (D).

    Click image to see an enlarged view

    Fig. Using a trim tool, pry out on the rear portion of the cover (A) to release the hooks (B, C), then remove the cover and the screws securing the inner handle (D)

  4.  
  5. Remove the power window switch panel (A), as follows:
    1. Pry up on the rear edge of the switch panel with a trim tool to release the rear clip
    2.  
    3. Pull out along the edge of the panel to release the hooks (B) and front clip.
    4.  
    5. Disconnect the power mirror switch connector (C) (driver's) and the power window switch connector (D)

      Click image to see an enlarged view

      Fig. Remove the power window switch panel-driver-s side shown, others similar

    6.  

  6.  
  7. Remove the screw from under the pull pocket cap (A).
  8.  
  9. Remove the mirror mount cover, as follows:
    1. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

      Click image to see an enlarged view

      Fig. Removing the mirror mount cover (A)

    2.  

  10.  
  11. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it, as follows:
    1. Start at the bottom edge of the door panel, release the clips that are just above the marks (B) on the edge of the panel with a commercially available trim pad remover.
    2.  
    3. Detach the upper clips.
    4.  
    5. Starting at the rear, pull the door panel upward and over the lock knob (C).
      NOTE
      The inner handle cable (D) and the courtesy light bulb socket (E) are connected to the door panel. Do not pull the door panel up too far, or the inner handle cable will be damaged



      Click image to see an enlarged view

      Fig. Door panel removal and installation-2003-06 Accord Sedan

    6.  

  12.  
  13. While holding the door panel (A) away from the door, disconnect the inner handle cable (B), and if equipped, courtesy light bulb socket (C), and detach the harness clip (D), then remove the panel. If necessary, remove the inner handle (E) by releasing the hooks (F, G).

    Click image to see an enlarged view

    Fig. While holding the door panel (A) away from the door, disconnect the inner handle cable (B), and if equipped, courtesy light bulb socket (C), and detach the harness clip (D), then remove the panel. If necessary, remove the inner handle (E) by releasing the hooks (F, G)

  14.  
  15. If necessary, remove the door glass inner weatherstrip (A) from the door panel (B) by pulling it down.

    Click image to see an enlarged view

    Fig. If necessary, remove the door glass inner weatherstrip (A) from the door panel (B) by pulling it down.

  16.  
  17. Disconnect the electrical connector, then remove the door lock actuator.
  18.  

To install:

  1. Install the door lock actuator and attach the electrical connector.
  2.  
  3. Install the panel in the reverse order of removal, and note these items:
    1. Check if the clip is damaged or stress-whitened, and if necessary, replace it with new one.
    2.  
    3. Make sure the connectors are plugged in properly, and the cable and the bulb socket are connected properly.
    4.  
    5. Make sure the window and power door lock operate properly.
    6.  
    7. When reinstalling the door panel, make sure the plastic cover is installed properly and sealed around its outside perimeter to seal out water.
    8.  
    9. Check for water leaks.
      NOTE
      Reset the power window control unit using one of the two following procedures.

    10.  

  4.  
  5. Resetting the power window control unit with an HDS:
    1. Connect the Honda Diagnostic System (HDS) to the vehicle's DLC.
    2.  
    3. Turn the ignition switch ON (II), then enter the vehicle's VIN and mileage at the prompts.
    4.  
    5. Select Body Electrical from the System Selection menu.
    6.  
    7. From the Body Electrical System Select menu, select Power Windows.
    8.  
    9. From the Mode menu, select Adjustments.
    10.  
    11. From the Adjustment menu, select Window P Reset.
    12.  
    13. Follow the prompts on the screen.
    14.  
    15. Confirm that the power window master switch is reset by using the driver's window AUTO UP and DOWN function.
    16.  

  6.  
  7. Resetting the power window control unit without an HDS:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's window all the way down by using the driver's window DOWN switch.
    4.  
    5. Open the driver's door.
      NOTE
      Steps d.-g. must be done within 5 seconds of each other.

    6.  
    7. Turn the ignition switch OFF.
    8.  
    9. Push and hold the driver's window DOWN switch.
    10.  
    11. Turn the ignition switch ON (II).
    12.  
    13. Release the driver's window DOWN switch.
    14.  
    15. Repeat steps d.-g. three more times.
    16.  
    17. Wait 1 second.
    18.  
    19. Confirm that AUTO UP and AUTO DOWN do not work. If AUTO UP and DOWN work, go back to step a.
    20.  
    21. Move the driver's window all the way down by holding the driver's window DOWN switch to the AUTO DOWN position.
    22.  
    23. Pull up and hold the driver's window UP switch to the AUTO UP position until the window reaches the fully closed position, then continue to hold the switch for 1 second.
    24.  
    25. Confirm that the power window master switch is reset by using the driver's window AUTO UP and DOWN function.
    26.  
    27. If the window still does not work in AUTO, repeat the procedure several times, paying close attention to the 5 second time limit between steps.
    28.  

  8.  
  9. Enter the anti-theft codes for the audio and the navigation system, then enter the audio presets
  10.  

  1. Remove the power window switch panel (A), as follows:
    1. Pry up on the rear edge of the switch panel with a trim tool to release the rear clip
    2.  
    3. Pull out along the edge of the panel to release the hooks (B) and front clip.
    4.  
    5. Disconnect the power mirror switch connector (C) (driver's) and the power window switch connector (D)

      Click image to see an enlarged view

      Fig. Remove the power window switch panel-driver-s side shown, others similar

    6.  

  2.  
  3. Remove the screws, then remove the door lock switch.
  4.  
  5. Installation is the reverse of the removal procedure
  6.  

 
label.common.footer.alt.autozoneLogo