Acura Coupes and Sedans 1986-1993 Repair Guide

Door Glass & Regulator

Imprimir

REMOVAL & INSTALLATION



1986-89 Integra
FRONT
  1. Remove the door panel.
  2.  
  3. Lower the glass until the glass mounting bolts are accessible.
  4.  
  5. Remove the bolts and pull the glass out of the frame.
  6.  
  7. Remove the regulator bolts, disconnect the harness and remove through the lower opening.
  8.  

To install:
  1. Lubricate the sliding portions of the regulator and install in the door.
  2.  
  3. Install the glass to the regulator. Install the door panel.
  4.  

REAR

See Figures 1 and 2



Click image to see an enlarged view

Fig. Fig. 1: Pull back the trim to remove the screws for the quarter glass-1986-89 Integra



Click image to see an enlarged view

Fig. Fig. 2: Rear door glass and regulator removal-1986-89 Integra

  1. Remove the door panel.
  2.  
  3. Pull back the upper weatherstrip to expose the screws for the quarterglass. Remove the screws and pull out the quarterglass.
  4.  
  5. Remove the 2 bolts holding the center channel and remove the channel.
  6.  
  7. Lower the glass until the glass mounting bolts are accessible.
  8.  
  9. Remove the bolts and pull the glass out of the frame.
  10.  
  11. Remove the regulator bolts, disconnect the harness and remove through the opening.
  12.  

To install:
  1. Lubricate the sliding portions of the regulator and install in the door.
  2.  
  3. Install the glass to the regulator. Install the center channel and the quarterglass.
  4.  
  5. Install the door panel.
  6.  

1990-93 Integra
FRONT (HATCHBACK)

See Figures 3, 4 and 5



Click image to see an enlarged view

Fig. Fig. 3: Removing the front sash-1990-93 Integra hatchback, front



Click image to see an enlarged view

Fig. Fig. 4: Removing the door glass-1990-93 Integra hatchback, front



Click image to see an enlarged view

Fig. Fig. 5: Removing the regulator-1990-93 Integra hatchback, front

  1. Remove the door panel.
  2.  
  3. Lower the glass and remove the stoppers.
  4.  
  5. Remover the front sash.
  6.  
  7. Remove the glass mounting bolts and the glass.
  8.  
  9. Mark the location of the roller guide nuts and remove the mounting hardware. Remove the regulator.
  10.  

To install:
  1. Lubricate the regulator sliding points. Install the regulator with the roller guide nuts in the original locations.
  2.  
  3. Install the glass, sash and the stoppers. Install the door panel.
  4.  

FRONT (SEDAN)

See Figures 6, 7 and 8



Click image to see an enlarged view

Fig. Fig. 6: Removing the front sash-1990-93 Integra sedan, front



Click image to see an enlarged view

Fig. Fig. 7: Removing the door glass-1990-93 Integra sedan, front



Click image to see an enlarged view

Fig. Fig. 8: Removing the regulator-1990-93 Integra sedan, front

  1. Remove the door panel.
  2.  
  3. Lower the glass and remove the sash.
  4.  
  5. Remover the stoppers.
  6.  
  7. Remove the glass mounting bolts and the glass.
  8.  
  9. Mark the location of the roller guide nuts and remove the mounting hardware. Remove the regulator.
  10.  

To install:
  1. Lubricate the regulator sliding points.
  2.  
  3. Install the regulator with the roller guide nuts in the original locations.
  4.  
  5. Install the glass, stopper and the sash.
  6.  
  7. Install the door panel.
  8.  

REAR (SEDAN)

See Figures 9, 10, 11 and 12



Click image to see an enlarged view

Fig. Fig. 9: Removing the front sash-1990-93 Integra sedan, rear



Click image to see an enlarged view

Fig. Fig. 10: Removing the door glass-1990-93 Integra sedan, rear



Click image to see an enlarged view

Fig. Fig. 11: Removing the regulator-1990-93 Integra sedan, rear



Click image to see an enlarged view

Fig. Fig. 12: Glass adjustment points-1990-93 Integra sedan, rear

  1. Remove the door panel.
  2.  
  3. Lower the glass.
  4.  
  5. Remover the stoppers.
  6.  
  7. Remove the glass mounting bolts and the glass.
  8.  
  9. Mark the location of the roller guide nuts and remove the mounting hardware. Remove the regulator.
  10.  

To install:
  1. Lubricate the regulator sliding points. Install the regulator with the roller guide nuts in the original locations.
  2.  
  3. Install the glass and the stopper.
  4.  
  5. Install the door panel.
  6.  

1986-90 Legend Sedan
FRONT

See Figure 13



Click image to see an enlarged view

Fig. Fig. 13: Removing the front door glass and regulator-1986-90 Legend sedan

  1. Remove the door panel.
  2.  
  3. Lower the glass until the glass mounting bolts are accessible.
  4.  
  5. Remove the bolts and pull the glass out of the frame.
  6.  
  7. Remove the regulator bolts, disconnect the harness and remove through the lower opening.
  8.  

To install:
  1. Lubricate the sliding portions of the regulator and install in the door.
  2.  
  3. Install the glass to the regulator. Install the door panel.
  4.  

REAR

See Figures 14, 15 and 16



Click image to see an enlarged view

Fig. Fig. 14: Removing the garnish pieces from the rear door-1986-90 Legend sedan



Click image to see an enlarged view

Fig. Fig. 15: Removing the quarter glass from the rear door-1986-90 Legend sedan



Click image to see an enlarged view

Fig. Fig. 16: Removing the rear door glass and regulator-1986-90 Legend sedan

  1. Remove the door panel. Remove the garnish pieces from the door.
  2.  
  3. Pull back the upper weatherstrip to expose the screws for the quarterglass. Remove the screws and pull out the quarterglass.
  4.  
  5. Remove the 2 bolts holding the center channel and remove the channel.
  6.  
  7. Lower the glass until the glass mounting bolts are accessible.
  8.  
  9. Remove the bolts and pull the glass out of the frame.
  10.  
  11. Remove the regulator bolts, disconnect the harness and remove through the opening.
  12.  

To install:
  1. Lubricate the sliding portions of the regulator and install in the door.
  2.  
  3. Install the glass to the regulator.
  4.  
  5. Install the center channel and the quarterglass. Install the garnish pieces.
  6.  
  7. Install the door panel.
  8.  

1986-90 Legend Coupe

See Figure 17



Click image to see an enlarged view

Fig. Fig. 17: Removing the regulator-1986-90 Legend Coupe

  1. Remove the door panel.
  2.  
  3. Lower the glass until the glass mounting bolts are accessible.
  4.  
  5. Remove the bolts and pull the glass out of the frame.
  6.  
  7. Remove the regulator bolts, disconnect the harness and remove through the center opening.
  8.  

To install:
  1. Lubricate the sliding portions of the regulator and install in the door.
  2.  
  3. Install the glass to the regulator. Install the door panel.
  4.  

1991-93 Legend Sedan
FRONT & REAR

See Figures 18 through 22



Click image to see an enlarged view

Fig. Fig. 18: Front door glass removal-1991-93 Legend sedan



Click image to see an enlarged view

Fig. Fig. 19: Front door regulator mounting-1991-93 Legend sedan



Click image to see an enlarged view

Fig. Fig. 20: Rear door glass removal-1991-93 Legend sedan



Click image to see an enlarged view

Fig. Fig. 21: Rear door channel removal-1991-93 Legend sedan



Click image to see an enlarged view

Fig. Fig. 22: Rear door regulator mounting-1991-93 Legend sedan

  1. Remove the door panel and inner shield. Remove the inner molding and stopper from the glass opening.
  2.  
  3. Remove the rear channel bolt and slide the channel back.
  4.  
  5. Lower the window to expose the glass mounting bolts. Remove the bolts and slide the guide back to remove the glass.
  6.  
  7. Remove the channels and the regulator mounting hardware. Remove the regulator from the door through the center hole.
  8.  

To install:
  1. Lubricate and install the regulator. Install the channels and the glass.
  2.  
  3. Slide the channel forward. Install the stopper, inner molding, inner shield and the door panel.
  4.  

1991-93 Legend Coupe

See Figures 23, 24, 25 and 26



Click image to see an enlarged view

Fig. Fig. 23: Door glass removal-1991-93 Legend Coupe



Click image to see an enlarged view

Fig. Fig. 24: Door channel removal-1991-93 Legend Coupe



Click image to see an enlarged view

Fig. Fig. 25: Door regulator mounting-1991-93 Legend Coupe



Click image to see an enlarged view

Fig. Fig. 26: Door regulator lubrications points-1991-93 Legend Coupe

  1. Remove the door panel and inner shield. Remove the inner molding from the glass opening.
  2.  
  3. Lower the window to expose the glass mounting bolts. Remove the bolts and slide the guide back to remove the glass.
  4.  
  5. Remove the channels and the regulator mounting hardware. Remove the regulator from the door through the center hole.
  6.  

To install:
  1. Lubricate and install the regulator. Install the channels and the glass.
  2.  
  3. Install the inner molding, inner shield and the door panel.
  4.  

Vigor
FRONT

See Figures 27 through 32



Click image to see an enlarged view

Fig. Fig. 27: Removing the front door sash and stopper-Vigor



Click image to see an enlarged view

Fig. Fig. 28: Removing the front door stabilizer-Vigor



Click image to see an enlarged view

Fig. Fig. 29: Removing the front door glass-Vigor



Click image to see an enlarged view

Fig. Fig. 30: Removing the front door guides-Vigor



Click image to see an enlarged view

Fig. Fig. 31: Removing the front door regulator-Vigor



Click image to see an enlarged view

Fig. Fig. 32: Front door regulator and guide lubrication points-Vigor

  1. Lower the window completely and remove the door panel, inner shield, mirror and outer molding.
  2.  
  3. Pull back the weatherstripping and remove the bolts and sash.
  4.  
  5. Remove the stopper plates and stabilizer.
  6.  
  7. Remove the glass mounting nuts and remove the glass.
  8.  
  9. Remove the mounting bolts for the guides and the guides.
  10.  
  11. Remove the mounting bolts for the regulator and the regulator.
  12.  

To install:
  1. Lubricate the guides and the regulator. Install the regulator and the guides. Install the glass.
  2.  
  3. Install the stabilizer and the stopper plates. Install the sash, molding and the mirror.
  4.  
  5. Install the inner shield and the door panel.
  6.  

REAR

See Figures 33 through 38



Click image to see an enlarged view

Fig. Fig. 33: Removing the rear door stopper-Vigor



Click image to see an enlarged view

Fig. Fig. 34: Removing the rear door stabilizer-Vigor



Click image to see an enlarged view

Fig. Fig. 35: Removing the rear door glass-Vigor



Click image to see an enlarged view

Fig. Fig. 36: Removing the rear door regulator-Vigor



Click image to see an enlarged view

Fig. Fig. 37: Rear door regulator and guide lubrication points-Vigor



Click image to see an enlarged view