Acura Coupes and Sedans 1986-1993 Repair Guide

Spark Plugs


See Figure 1

Early Acura models use standard spark plugs that should be replaced after 30,000 miles. Late model vehicles use platinum tipped spark plugs that do not need to be replaced until 60,000 miles. Check your owners manual if you are not sure of the type of spark plugs in your vehicle.

Most people know that the spark plug ignites the air/fuel mixture in the cylinder, which in turn forces the piston downward, turning the crankshaft. This action turns the drivetrain (clutch, transaxle, drive axles) and moves the vehicle. What many people do not know, however, is that spark plugs should be chosen according to the type of driving done. The plug with a long insulator nose retains heat long enough to burn off oil and combustion deposits under light engine load conditions. A short-nosed plug dissipates heat rapidly and prevents pre-ignition and detonation under heavily loaded conditions. Under normal driving conditions, a standard plug is just fine.

Click image to see an enlarged view

Fig. Fig. 1: Cross section of a spark plug

Spark plug life is largely governed by operating conditions and varies accordingly. To ensure peak performance, inspect the plugs at least every 10,000-15,000 miles. Faulty or excessively worn plugs should be replaced immediately. It is also helpful to check plugs for types of deposit and degree of electrode wear, as an indication of engine operating condition. Excessive or oily deposits could be an indication of real engine trouble, it would be wise to investigate the problem thoroughly and make sure the cause is found and corrected.


See Figures 2 through 6

Click image to see an enlarged view

Fig. Fig. 2: Inspect these areas of the spark plug when checking them

Click image to see an enlarged view

Fig. Fig. 3: Clean between the outer shell and insulator with a stiff wire

Click image to see an enlarged view

Fig. Fig. 4: Adjusting the spark plug gap

On models with distributorless ignition, the ignition coils are located directly on top of each spark plug. The coils must be removed before the spark plug. The coil removal procedure can be found later in this section.

  1. Place a piece of masking tape around each spark plug wire and number it according to its corresponding cylinder.

Click image to see an enlarged view

Fig. Fig. 5: Remove the spark plug wire by pulling it firmly from the valve cover-Integra

Click image to see an enlarged view

Fig. Fig. 6: Removing the spark plug from the cylinder head-Integra

  1. Pull the wires from the spark plugs, grasping the wire by the end of the rubber boot and twisting off.

Avoid spark plug removal while the engine is Hot. Since the cylinder head spark plug threads are aluminum, the spark plug becomes tight due to the different coefficients of heat expansion. If a plug is too tight to be removed even while the engine is Cold, apply a solvent around the plug followed with an application of oil once the solvent has penetrated the threads. Do this only when the engine is Cold.

  1. Loosen each spark plug with a spark plug socket. When the plug has been loosened a few turns, stop to clean any material from around the spark plug holes; compressed air is preferred. If air is not available, simply use a rag to clean the area.

In no case should foreign matter be allowed to enter the cylinders. Severe engine damage could result.

  1. Remove and inspect the spark plugs; if necessary, clean them.

To install:
  1. Check the gap of the plugs with a feeler gauge. Oil the spark plug threads and hand tighten them into the cylinder head. Torque the spark plugs into the cylinder head to 16 ft. lbs. (22 Nm).

It's a good idea to apply an anti-seize compound on the threads of the spark plugs before installing them. Do not over-tighten the spark plugs, as this could damage the aluminum cylinder heads.

  1. Connect the wires to the plugs, in the correct order, making sure that each is securely fitted.


Before attempting to clean and re-gap plugs be sure that the electrode ends are not worn or damaged and that the insulators (the white porcelain covering) are not cracked; replace the plug if this condition exists.

Clean reusable plugs with a small file or a wire brush. The plug gap should be checked and readjusted, if necessary, by bending the ground electrode with a spark plug gapping tool.

Do not use a flat gauge to check plug gap. An incorrect reading will result; use a wire gauge only. Also, replace the plugs one at a time, keeping the ignition wires connected to those plugs you're not working on. This will avoid confusion about how to reconnect the plug wires according to the firing order.