Altima 2007-2009

Engine Coolant Temperature Sensor

Print

Location



Specific to:

Nissan Altima 2009-2010



Click image to see an enlarged view

Fig. ECT location (9)-2.5L engine



Click image to see an enlarged view

Fig. ECT location (3)-3.5L engine

2.5L Engine

Specific to:

Nissan Altima 2007-2008

Refer to the accompanying illustration for sensor location.

Click image to see an enlarged view

Fig. The ECT sensor is in the water outlet assembly near the upper radiator hose connection-2.5L engine

3.5L Engine

Specific to:

Nissan Altima 2007-2008

Refer to the accompanying illustration for sensor location.

Click image to see an enlarged view

Fig. The ECT sensor is in the water outlet assembly between the cylinder heads near the front head-3.5L engine

Operation



Specific to:

Nissan Altima 2007-2008

The Engine Coolant Temperature (ECT) sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the ECM. The modified signal returns to the ECM as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.

Reference data values are measured between ECM terminal 46 (Engine coolant temperature sensor) and ground.


WARNING
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in damage to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.

Specific to:

Nissan Altima 2009-2010

The Engine Coolant Temperature (ECT) Sensor is a Negative Temperature Coefficient (NTC) Thermistor that monitors the engine coolant temperature. The ECT Sensor operates within a 5 volt DC reference range, and provides a linear input signal to the Powertrain Control Module (PCM) that is based upon the measured engine coolant temperature. The PCM uses data from the ECT Sensor to calculate air-fuel mixture, ignition timing, and fuel injector pulse width. In some instances, the ECT signal is used to control the engine cooling fans and the operation of the air conditioning (A/C) system.

Removal & Installation



Specific to:

Nissan Altima 2007-2008

  1. With the ignition switch OFF , unplug the sensor connector.
  2.  
  3. Unscrew the sensor.
  4.  
  5. During installation, use a new O-ring and make sure the sensor is clean.

    Click image to see an enlarged view

    Fig. The ECT sensor is in the water outlet assembly near the upper radiator hose connection-2.5L engine



    Click image to see an enlarged view

    Fig. The ECT sensor is in the water outlet assembly between the cylinder heads near the front head-3.5L engine

  6.  

Specific to:

Nissan Altima 2009-2010

  1. Turn ignition switch OFF.
  2.  
  3. Disconnect engine coolant temperature sensor harness connector.
  4.  
  5. Remove engine coolant temperature sensor.
  6.  
  7. Installation is the reverse of removal.
  8.  

Testing



Specific to:

Nissan Altima 2007-2008

  1. Turn ignition switch ON and wait at least 5 seconds.
  2.  
  3. Check DTC. Is DTC detected-
  4.  
  5. Turn the ignition switch OFF and unplug the wiring harness from the sensor.
  6.  
  7. Turn the ignition switch ON and check for 5 volts between terminal 1 on the wiring harness connector and chassis ground. If there is no voltage or if there is voltage at both terminals, check the wiring harness for damage that might cause open or short circuits.
  8.  
  9. Check for voltage across both terminals on the wiring harness connector. If there is no voltage, check the wiring harness for damage. The ground is provided by the ECM.
    WARNING
    Connect the voltmeter ground probe to engine or chassis ground. Do not test circuits with the meter connected to the negative battery terminal or the ECM may be damaged.

  10.  
  11. Turn ignition switch OFF .
  12.  
  13. Check the resistance across sensor terminals 1 and 2. Compare your reading with the table below. If resistance is incorrect, replace the sensor.

    Click image to see an enlarged view

    Fig. Engine coolant temperature sensor resistance

  14.  

Specific to:

Nissan Altima 2009-2010


NOTE
Refer to the Electrical Wiring Diagram for component and connector locations, connector views, and circuit-specific information.

Connection & Wiring Diagnosis

Specific to:

Nissan Altima 2009-2010

Refer to the Electrical Wiring Diagram for component and connector locations, connector views, and circuit-specific information.

Many intermittent open or short circuits may be caused by wiring harness and connector movement due to vibration, engine torque, bumps and rough pavement, etc.

  1. Test the wiring harness and connectors by performing the following tests:

    Move the related connectors and wiring while monitoring the appropriate scan tool data.
     
    Move the related connectors and wiring with the component commanded ON and OFF. Using a suitable the scan tool, observe the component operation.
     
    With the engine running, move the related connectors and wiring while monitoring component operation.
     
    If harness or connector movement affects the data displayed, the component and system operation, or the engine operation, inspect and repair the harness or connections as necessary.
     

  2.  
  3. Test the connector terminal pins and/or wiring by performing the following tests:

    Inspect for incorrect mating of the connector halves, or terminals not fully seated in the connector body.
     
    Inspect for improperly formed or damaged terminals and test for incorrect terminal tension.
     
    Inspect for poor terminal to wire connections including terminals crimped over insulation. This requires removing the terminal from the connector body.
     
    Inspect for corrosion or water intrusion. Pierced or damaged insulation can allow moisture to enter the wiring. The conductor can corrode inside the insulation with little visible evidence. Look for swollen and/or brittle sections of wire in the suspect circuits.
     
    Inspect for wires that are broken inside the insulation by gently pulling on suspect sections of wiring.
     

  4.  

ECT Circuit Testing

Specific to:

Nissan Altima 2009-2010

Use a suitable scan tool, a Graphing Multi-Meter (GMM), or a Digital Volt-Ohm Meter (DVOM) in order to view the ECT data.

ECT Sensor logic is relative to the scale of resistance: when the coolant temperature is low, the voltage is increased. When the coolant temperature is high, the voltage is decreased.

Use a suitable pyrometer or thermometer, as well as visual observation to verify that the cooling system is operating properly. If a cooling system fault is evident, repair as required before continuing.

If a DVOM is being used, additional information may be acquired by taking measurements at the sensor connector as well as the PCM connector. If a significant voltage drop is measured (greater than 0.5 volts DC), check the wiring harness and connections for corrosion, poor pin connections, or damaged wires.

If all engine wiring and pin connections are confirmed, disconnect the ECT Sensor to verify the signal with a DVOM, and verify PCM communication before replacing the ECT Sensor.

Click image to see an enlarged view

Fig. ECT Sensor Range Chart

ECT Sensor Strategy

Specific to:

Nissan Altima 2009-2010

The ECT Sensor provides a linear input signal to the Powertrain Control Module (PCM) for a number of engine control system calculations. The ECT signal is compared with Manifold Absolute Pressure (MAP), Mass Air Flow (MAF), Intake Air Temperature (IAT), and Fuel Trim (HO2S) in order to determine the correct air-fuel mixture for measured operating conditions. In some cases the ECT Sensor input is used in concert with the A/C Pressure (ACP) Sensor input in order to determine cooling fan and A/C system operation.

Related Diagnostic Trouble Codes

Specific to:

Nissan Altima 2009-2010



Click image to see an enlarged view

Fig. Related Diagnostic Trouble Codes

 
label.common.footer.alt.autozoneLogo