Honda CRV/Odyssey 1995-2000 Repair Information

Wheel Speed Sensor


Each wheel has its own wheel speed sensor which sends a small AC electrical signal to the control module. Correct ABS operation depends on accurate wheel speed signals. The vehicle's wheels and tires must all be the same size and type in order to generate accurate signals. If there is a variation between wheel and tire sizes, inaccurate wheel speed signals will be produced.

It is very critical that the wheel speed sensor(s) be installed correctly to ensure continued system operation. The sensor cables must be installed, routed and clipped properly. Failure to install the sensor(s) properly could result in contact with moving parts or over extension of sensor cables. This will cause ABS component failure and an open circuit. See Figure 1

Click image to see an enlarged view

Fig. Fig. 1: The ABS rear wheel sensor and tone ring mounting and location- CRV model shown

Honda uses a contactless type of sensor that detects the rotating speed of the wheel. It is constructed of a permanent magnet and a coil. Attached to the rotating parts are gear pulsers (a.k.a. Tone Rings). When these pulsers turn, the magnetic flux around the coil in the wheel sensor alternates its current. This generates voltages in a frequency or wave pattern. These wave pulses are sent to the ABS control unit which identifies the speed of each of the four wheels.


Vehicles equipped with air bag systems (SRS) have components and wiring in the same area as the front speed sensor wiring harnesses. The air bag system connectors are yellow. Do not use electrical test equipment on these circuits. Do not damage the SRS wiring while working on other wiring or components. Failure to observe correct procedures may cause the air bag system to inflate unexpectedly or render the system totally inoperative.

  1. Raise and safely support the vehicle as necessary for access.
  3. Make certain the ignition switch is OFF .

See Figure 2

Click image to see an enlarged view

Fig. Fig. 2: Typical front wheel speed sensor mounting- CRV model shown

  1. Detach the sensor harness connector.
  3. Beginning at the connector end, remove grommets, clips or retainers as necessary to free the harness. Take careful note of the placement and routing of the harness; it must be reinstalled in the exact original position.
  5. Remove the bolt holding the speed sensor to its mounting, then remove the sensor. If it is stuck in place, gently tap on the side of the mounting flange with a hammer and small punch; do not tap on the sensor.

See Figure 3

Click image to see an enlarged view

Fig. Fig. 3: The ABS rear wheel speed sensor is held in place by two mounting bolts- CRV model shown

To install:
  1. Place the sensor in position; install the retaining bolts loosely. Route the harness correctly. Avoid twisting or crimping the harness; use the white line on the wires as a guide.
  3. Once the harness and sensor are correctly but loosely placed, tighten the sensor mounting bolts. Tighten bolts to 16 ft. lbs. (22 Nm).
  5. Working from the sensor end to the connector, install each clip, retainer, bracket or grommet holding the sensor harness. The harness must not be twisted. Tighten any bolt holding brackets to 84 inch lbs. (10 Nm).
  7. Attach the wiring connector.
  9. Use the ABS checker to check for proper signal from the wheel speed sensor.
  11. Carefully lower the vehicle to the ground.


See Figures 4 and 5

Click image to see an enlarged view

Fig. Fig. 4: The air gap on this style sensor is measured from the tip of the ABS sensor core and the tone ring. This is a typical ABS sensor found on disc brakes

Click image to see an enlarged view

Fig. Fig. 5: The air gap on this style sensor is measured between the inside edge of the ABS sensor core and the tone ring. This is a typical ABS sensor used on drum brakes

  1. Use a non-metallic feeler gauge to measure the gap between the sensor and the pulser.
  3. Rotate the hub or axle slowly by hand, taking measurements at several locations.
  5. Compare with the following specifications:

CRV and 4-cylinder Odyssey models:

Front and Rear: 0.020-0.040 in. (0.5-1.0mm)

V6 Odyssey models:

Front:0.020-0.040 in. (0.5-1.0mm)
Rear:0.010-0.040 in. (0.2-1.1mm)