Audi Cars 1999-05

Heated Oxygen Sensor 2

Print

Testing




NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  


NOTE
When servicing the terminals in the harness connector of Heated Oxygen Sensor (HO2S), use only gold-plated terminals.

  1. Connect to the vehicle diagnosis and service system (VAS).
  2.  
  3. Start the engine and let it run at idle.
  4.  
  5. Under address word "33 - On Board Diagnostic (OBD)", select "Diagnostic mode 6: Check test results of components that are not continuously monitored".
  6.  
  7. Select "Test-ID 01: Oxygen sensor monitoring before catalytic converter" .
  8.  
  9. Select "Test-ID 131: Dynamic test" and check whether specified values are obtained.
  10.  
  11. If the specified values are not obtained:
  12.  
  13. Check the oxygen sensor wiring.
  14.  
  15. Connect the test box to the wiring harness of the Motronic Engine Control Module (ECM)
  16.  
  17. Disconnect the black 6-pin harness connector to the Heated Oxygen Sensor (HO2S).

    Click image to see an enlarged view

    Fig. Check wires between test box and 6-pin connector for open circuit according to wiring diagram.

  18.  
  19. Check the wires between the test box and the 6-pin connector for an open circuit according to the wiring diagram.

    Terminal 1 and socket 52
     
    Terminal 2 and socket 51
     
    Terminal 3 and socket 36
     
    Terminal 5 and socket 71
     
    Terminal 6 and socket 70
     

  20.  
  21. Wire resistance: max. 1.5 ohms
  22.  
  23. Check the wires for short circuit to each other, to Battery (+) and Ground (GND).
  24.  
  25. Specified value: infinite ohms
  26.  
  27. If the wires are okay, replace the Heated Oxygen Sensor (HO2S) G39 before catalytic converter.
  28.  

 
label.common.footer.alt.autozoneLogo