Audi Cars 1999-05

1.8L L4 VIN B Auto 4

Print

Trouble Code: P0605



ECM Read Only Memory (ROM) Test Error

Possible Causes:



An attempt was made to change the module calibration, or a module programming error may have occurred
 
Clear the trouble codes and then check for this trouble code. If it resets, the ECM has failed and needs replacement.
 
Aftermarket performance products may have been installed.
 
The Transmission Control Module (TCM) has failed.
 

Trouble Code: P0606



ECM Internal Communication Error

Possible Causes:



Clear the trouble codes and then check for this trouble code. If it resets, the ECM has failed and needs replacement.
 
Remember to check for signs of Aftermarket Performance Products installation before replacing the ECM.
 

Trouble Code: P0638



Throttle Actuator Control Range/Performance Bank 1

Possible Causes:



Throttle Position (TP) sensor is faulty
 
Throttle valve control module is faulty
 
ECM is faulty
 
Circuit wires have short circuited to each other, to vehicle Ground (GND) or to B+.
 
Accelerator pedal module is faulty
 

Trouble Code: P0685



ECM Power Relay Control Circuit Open

Possible Causes:



Generator has failed or is damaged
 
Fuel pump relay is faulty
 
Circuit is grounded to power or chassis
 
ECM has failed
 

Trouble Code: P0686



ECM/PCM Power Relay Control Circuit Low

Possible Causes:



Generator has failed or is damaged
 
Fuel pump relay is faulty
 
Circuit is grounded to power or chassis
 
ECM has failed
 

Trouble Code: P0687



ECM/PCM Power Relay Control Circuit High

Possible Causes:



Generator has failed or is damaged
 
Fuel pump relay is faulty
 
Circuit is grounded to power or chassis
 
ECM has failed
 

Trouble Code: P0688



ECM/PCM Power Relay Control Sense Circuit Open

Possible Causes:



Generator has failed or is damaged
 
Fuel pump relay is faulty
 
Circuit is grounded to power or chassis
 
ECM has failed
 

Trouble Code: P0707



Transmission Range Sensor Circuit Low Input

Possible Causes:



Circuit harness connector contacts are corroded or ingressed of water
 
Circuit wires have shorted to each other, to battery or ground
 
Automatic Transmission Hydraulic Pressure Sensor 1 has failed
 
Solenoid valves in valve body are faulty
 
Transmission Input Speed (RPM) Sensor has failed
 
Transmission Output Speed (RPM) Sensor has failed
 
Engine Control Module (ECM) is faulty
 
Voltage supply for Engine Control Module (ECM) is faulty
 
Transmission Control Module (TCM) is faulty
 

Trouble Code: P0708



Transmission Range Sensor Circuit High Input

Possible Causes:



Circuit harness connector contacts are corroded or ingressed of water
 
Circuit wires have shorted to each other, to battery or ground
 
Automatic Transmission Hydraulic Pressure Sensor 1 has failed
 
Solenoid valves in valve body are faulty
 
Transmission Input Speed (RPM) Sensor has failed
 
Transmission Output Speed (RPM) Sensor has failed
 
Engine Control Module (ECM) is faulty
 
Voltage supply for Engine Control Module (ECM) is faulty
 
Transmission Control Module (TCM) is faulty
 

Trouble Code: P1103



O2 Sensor Circuit (Bank 1-Sensor 1) Output Too Low

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1105



O2 Sensor Circuit (Bank 1-Sensor 2) Short to B+

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1111



O2 Control (Bank 1) System Too Lean

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1112



O2 Control (Bank 1) System Too Rich

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1113



O2 Control (Bank 1 Sensor 1) Internal Resistance Too High

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1114



O2 Control (Bank 1 Sensor 2) Internal Resistance Too High

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1115



O2 Control (Bank 1 Sensor 1) Short to Ground

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1116



O2 Control (Bank 1 Sensor 1) Open

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1117



O2 Control (Bank 1 Sensor 2) Open

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1118



O2 Sensor Heater Circ. (Bank 1-Sensor2) Open

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1127



Long Term Fuel Trim Add. Air. Bank 1 System Too Rich

Possible Causes:



MAF sensor circuit open
 
MAF sensor circuit shorted to ground
 
Air leak in the manifold
 
Secondary air injection system combi-valve stuck open
 
Secondary air injection system electrical short
 
Fuel pressure too high, leaks in the vacuum hose to fuel pressure regulator
 
Fuel pressure regulator has failed
 
Fuel injectors are dirty, faulty or do not close properly
 
ECM has failed
 

Trouble Code: P1128



Long Term Fuel Trim Add. Air. Bank 1 System Too Lean

Possible Causes:



Fuel pressure is too low or fuel quantity supplied is too low
 
Fuel filter faulty
 
Transfer fuel pump has failed
 
Fuel injector is faulty (sticking or not opening)
 
Engine speed (RPM) sensor is faulty
 
MAF sensor circuit open
 
MAF sensor circuit shorted to ground
 
Air leak in the manifold
 
Secondary air injection system combi-valve stuck open
 
Secondary air injection system electrical short
 
ECM has failed
 

Trouble Code: P1136



Long Term Fuel Trim Add. Fuel, Bank 1 System Too Lean

Possible Causes:



Air intake system leaking, vacuum hoses leaking or damaged
 
Air leaks located after the MAF sensor mounting location
 
EGR valve sticking, EGR diaphragm leaking, or gasket leaking
 
EVAP vapor recovery system has failed
 
Excessive fuel pressure, leaking or contaminated fuel injectors
 
Exhaust leaks before or near the HO2S(s) mounting location
 
Fuel pressure regulator is leaking or damaged
 
HO2S circuits wet or oily, corroded, or poor terminal contact
 
HO2S is damaged or it has failed
 
HO2S signal circuit open, shorted to ground, shorted to power
 
Low fuel pressure or vehicle driven until it was out of fuel
 
Oil dipstick not seated or engine oil level too high (overfilled)
 

Trouble Code: P1137



Long Term Fuel Trim Add. Fuel, Bank 1 System Too Rich

Possible Causes:



Air intake system leaking, vacuum hoses leaking or damaged
 
Air leaks located after the MAF sensor mounting location
 
EGR valve sticking, EGR diaphragm leaking, or gasket leaking
 
EVAP vapor recovery system has failed
 
Excessive fuel pressure, leaking or contaminated fuel injectors
 
Exhaust leaks before or near the HO2S(s) mounting location
 
Fuel pressure regulator is leaking or damaged
 
HO2S circuits wet or oily, corroded, or poor terminal contact
 
HO2S is damaged or it has failed
 
HO2S signal circuit open, shorted to ground, shorted to power
 
Low fuel pressure or vehicle driven until it was out of fuel
 
Oil dipstick not seated or engine oil level too high (overfilled)
 

Trouble Code: P1141



Load Calculation Cross Check Range/Performance

Possible Causes:



Intake system is leaking
 
Signal is grounding
 
ECM has failed
 
Intake Manifold Runner Position Sensor is faulty
 
Intake system for leaks (false air) is faulty
 
Motor for intake flap is faulty
 
Mass Air Flow (MAF) sensor is faulty
 
Throttle Position (TP) sensor is faulty
 
Throttle valve control module is faulty
 

Trouble Code: P1143



Load Calculation Cross Check Upper Limit

Possible Causes:



Intake Manifold Runner Position Sensor is faulty
 
Intake system for leaks (false air) is faulty
 
Motor for intake flap is faulty
 
Mass Air Flow (MAF) sensor is faulty
 
Throttle Position (TP) sensor is faulty
 
Throttle valve control module is faulty
 
Intake system is leaking
 
Signal is grounding
 
ECM has failed
 

Trouble Code: P1149



O2 Control (Bank 1) Out of Range

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Circuit wiring has a short to power or ground
 
Engine Component Power Supply Relay is faulty
 
E-box fuses for oxygen sensor are faulty
 
Leaks present in the exhaust manifold or exhaust pipes
 
HO2S signal wire and ground wire crossed in connector
 
HO2S element is fuel contaminated or has failed
 
ECM has failed
 

Trouble Code: P1171



Throttle Actuation Potentiometer Sign.2 Range/Performance

Possible Causes:



Throttle valve control module has failed
 
Throttle valve is dirty or damaged
 
Throttle valve is not in a closed position
 
Voltage supply of throttle valve control module is shorted or open
 
ECM has failed
 

Trouble Code: P1176



O2 Correction Behind Catalyst B1 Limit Attained

Possible Causes:



O2 sensor circuit has shorted to ground or B+
 
O2 sensor circuit is open
 
ECM has failed
 
O2 sensor has failed
 
Intake Manifold Runner Position Sensor is faulty
 
Intake system for leaks (false air) is faulty
 
Motor for intake flap is faulty
 

Trouble Code: P1177



O2 Correction Behind Catalyst B2 Limit Attained

Possible Causes:



O2 sensor circuit has shorted to ground or B+
 
O2 sensor circuit is open
 
ECM has failed
 
O2 sensor has failed
 
Intake Manifold Runner Position Sensor is faulty
 
Intake system for leaks (false air) is faulty
 
Motor for intake flap is faulty
 

Trouble Code: P1196



O2 Sensor Heater Circuit (Bank 1-Sensor 1) Electrical Malfunction

Possible Causes:



HO2S heater power circuit is open
 
HO2S heater ground circuit is open
 
HO2S signal tracking (due to oil or moisture in the connector)
 
HO2S is damaged or has failed
 
ECM has failed
 
Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 

Trouble Code: P1198



O2 Sensor Heater Circuit (Bank 1-Sensor 2) Electrical Malfunction

Possible Causes:



HO2S heater power circuit is open
 
HO2S heater ground circuit is open
 
HO2S signal tracking (due to oil or moisture in the connector)
 
HO2S is damaged or has failed
 
ECM has failed
 
Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 

Trouble Code: P1201



Cylinder 1 Fuel Injection Circuit Electrical Malfunction

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Fuel injectors may have malfunctioned
 
Faulty engine speed sensor
 

Trouble Code: P1202



Cylinder 2 Fuel Injection Circuit Electrical Malfunction

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Fuel injectors may have malfunctioned
 
Faulty engine speed sensor
 

Trouble Code: P1203



Cylinder 3 Fuel Injection Circuit Electrical Malfunction

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Fuel injectors may have malfunctioned
 
Faulty engine speed sensor
 

Trouble Code: P1204



Cylinder 4 Fuel Injection Circuit Electrical Malfunction

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Fuel injectors may have malfunctioned
 
Faulty engine speed sensor
 

Trouble Code: P1213



Cylinder 1 Fuel Injection Circuit Short to B+

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Engine speed sensor has failed
 

Trouble Code: P1214



Cylinder 2 Fuel Injection Circuit Short to B+

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Engine speed sensor has failed
 

Trouble Code: P1215



Cylinder 3 Fuel Injection Circuit Short to B+

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Engine speed sensor has failed
 

Trouble Code: P1216



Cylinder 4 Fuel Injection Circuit Short to B+

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Engine speed sensor has failed
 

Trouble Code: P1225



Cylinder 1 Fuel Injection Circuit Short to Ground

Possible Causes:



Injector control circuit is open
 
Injector power circuit (B+) is open
 
Injector control circuit is shorted to chassis ground
 
Injector is damaged or has failed
 
ECM is not connected or has failed
 
Fuel pump relay has failed
 
Engine speed sensor has failed
 

 
label.common.footer.alt.autozoneLogo