Aura, Outlook 2007

Removal & Installation

Print

  1. Drain and recycle the engine coolant.
  2.  
  3. Remove the air cleaner outlet air duct on the 2.4L engine.
  4.  
  5. Remove the air cleaner inlet air duct on the 3.5 and 3.6L engines
  6.  
  7. Remove the upper radiator air deflector.
  8.  
  9. Remove the transmission oil cooler pipes from the radiator.
  10.  
  11. Loop a rope around each of the upper 2 tabs of the condenser and tie a rope around the upper tie bar.
  12.  
  13. Remove the upper radiator support bracket bolts.
  14.  
  15. Remove the upper radiator support brackets.
  16.  
  17. Pry upward on the fan shroud tabs at the radiator clips to release the fan shroud from the radiator.
  18.  
  19. Remove the lower radiator air deflector.
  20.  
  21. Lower the vehicle.
  22.  
  23. Remove the radiator inlet hose from the radiator.
  24.  
  25. Remove the radiator outlet hose from the radiator.
  26.  
  27. Disconnect the cooling fan wire harness connectors.
  28.  
  29. Remove the A/C compressor and condenser hose assembly.
  30.  
  31. Raise the vehicle.
  32.  
  33. Remove the lower radiator support bracket bolts.
  34.  
  35. Remove the lower radiator support brackets.
  36.  
  37. Remove the transmission oil cooler pipe clip from the fan shroud.
  38.  
  39. Remove the fan assembly.
  40.  

To install:

  1. Install the fan shroud assembly.
  2.  
  3. Install the transmission oil cooler pipes to the radiator.
  4.  
  5. Install the transmission oil cooler pipe clip to the fan shroud.
  6.  
  7. Install the lower radiator support brackets.
  8.  
  9. Install the lower radiator support bracket bolts and tighten to 44 ft. lbs. (60 Nm).
  10.  
  11. Install the cooling fan wire harness connectors.
  12.  
  13. Install the radiator outlet hose to the radiator.
  14.  
  15. Install the lower radiator air deflector.
  16.  
  17. Lower the vehicle.
  18.  
  19. Snap fan shroud tabs into the radiator clips.
  20.  
  21. Remove the rope attached to the condenser and upper tie bar.
  22.  
  23. Install the upper radiator support brackets.
  24.  
  25. Install the upper radiator support bracket bolts and tighten to 89 in. lbs. (10 Nm).
  26.  
  27. Install the radiator inlet hose to the radiator.
  28.  
  29. Install the A/C compressor and condenser hose assembly.
  30.  
  31. Install the upper radiator air deflector.
  32.  
  33. Install the air duct.
  34.  
  35. Fill the cooling system.
  36.  
  37. Inspect the transmission fluid level.
  38.  

  1. Disconnect electrical connector at fan shroud harness.
  2.  
  3. Remove front fascia upper support.
  4.  
  5. Remove hood latch support.
  6.  
  7. Remove upper radiator mounting brackets and tip radiator forward for additional clearance.
  8.  
  9. Remove the shroud mounting bolts and the pushpin retainers.
  10.  
  11. Remove the fan shroud and fan assembly. It may be necessary to tilt the assembly rearwards and upwards to remove.
  12.  

To install:

  1. Installation is the reverse of removal.
  2.  

 
label.common.footer.alt.autozoneLogo