Avalanche, Sierra, Silverado, C&K Series, 1999-2005

4.3L V6 VIN X Std 3

Print

Trouble Code: P0506



Idle Speed Too Low

Possible Causes:



Air inlet duct is collapsed, loose or air filter element is clogged
 
Base engine problem (i.e., compression or misfire condition)
 
IAC solenoid control circuit has a high resistance condition
 
IAC valve is damaged or has failed
 
Idle air inlet passage or throttle bore is dirty or full of deposits
 
MAF sensor is dirty, out-of-calibration or it is "skewed"
 
Throttle plate, throttle shaft or linkage is damaged or sticking
 
PCM has failed
 

Trouble Code: P0560



System Voltage Malfunction

Possible Causes:



Check for high resistance at the battery connections or at the Underhood Fuse Block power circuit connection to the PCM
 
Check the drive belt for excessive wear and the proper tension
 
Check the condition of the battery and the Generator output
 
Vehicle may have been used to jump-start another vehicle
 

Trouble Code: P0563



System Voltage Too High

Possible Causes:



Check the condition of the battery (it may be worn out)
 
Test the operation of the Generator (it may have failed)
 
Vehicle may have been used to jump-start another vehicle
 

Trouble Code: P0601



Control Module ROM Malfunction

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 
TSB 67-65-23 contains a repair procedure for this code
 

Trouble Code: P0602



Control Module Not Programmed

Possible Causes:



Reprogram the PCM with the correct software and calibration. If this step does not correct the problem, the PCM must be replaced and programmed with the correct software/calibration.
 

Trouble Code: P0603



Control Module Long Term Memory Reset

Possible Causes:



An interruption to the PCM main power and/or ground circuits
 
Check the PCM power and ground circuits and make repairs as necessary. Clear the codes and recheck. If it resets, the PCM must be replaced and programmed with the correct software.
 

Trouble Code: P0604



Control Module Random Access Memory Failure

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0605



Control Module Programming Read Only Memory

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0606



Control Module Internal Performance

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0607



Control Module Performance

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0611



Control Module Performance

Possible Causes:



FICM is damaged
 

Trouble Code: P0641



5-Volt Reference 1 Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to MAP or TP sensor circuit is shorted to (B+)
 
PCM has failed
 

Trouble Code: P0650



Malfunction Indicator Lamp Circuit Malfunction

Possible Causes:



MIL control circuit is open or shorted to ground
 
MIL control circuit is shorted to system power
 
MIL control power circuit is open in the Instrument Cluster
 
MIL (the lamp) is damaged or has failed
 
Instrument Cluster or the PCM has failed
 

Trouble Code: P0651



5-Volt Reference 2 Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to MAP or TP sensor circuit is shorted to (B+)
 
PCM has failed
 

Trouble Code: P0704



Clutch Switch Circuit Malfunction

Possible Causes:



Clutch switch circuit is open, shorted to ground or to power
 
Clutch switch power circuit is open (test the ENG IGN fuse)
 
Clutch switch is out of adjustment, damaged or has failed
 
PCM has failed
 

Trouble Code: P1020



Camshaft Phasing System Malfunction

Possible Causes:



AF fuel mode relay circuit (odd bank, even bank) is open
 
AF enable circuit is open or shorted to ground
 
FICM is damaged or it has failed
 

Trouble Code: P1021



CNG Fuel Injector 1 Circuit Malfunction

Possible Causes:



CNG fuel injector 1 control circuit is open or shorted to ground
 
CNG fuel injector 1 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1022



CNG Fuel Injector 2 Circuit Malfunction

Possible Causes:



CNG fuel injector 2 control circuit is open or shorted to ground
 
CNG fuel injector 2 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1023



CNG Fuel Injector 3 Circuit Malfunction

Possible Causes:



CNG fuel injector 3 control circuit is open or shorted to ground
 
CNG fuel injector 3 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1024



CNG Fuel Injector 4 Circuit Malfunction

Possible Causes:



CNG fuel injector 4 control circuit is open or shorted to ground
 
CNG fuel injector 4 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1025



CNG Fuel Injector 5 Circuit Malfunction

Possible Causes:



CNG fuel injector 5 control circuit is open or shorted to ground
 
CNG fuel injector 5 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1026



CNG Fuel Injector 6 Circuit Malfunction

Possible Causes:



CNG fuel injector 6 control circuit is open or shorted to ground
 
CNG fuel injector 6 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1027



CNG Fuel Injector 7 Circuit Malfunction

Possible Causes:



CNG fuel injector 7 control circuit is open or shorted to ground
 
CNG fuel injector 7 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1028



CNG Fuel Injector 8 Circuit Malfunction

Possible Causes:



CNG fuel injector 8 control circuit is open or shorted to ground
 
CNG fuel injector 8 is damaged or it has failed
 
FICM has failed
 

Trouble Code: P1106



MAP Sensor Circuit Intermittent High Input

Possible Causes:



MAP sensor signal circuit is shorted to VREF (intermittent fault)
 
MAP sensor ground circuit is open (intermittent fault)
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1107



MAP Sensor Circuit Intermittent Low Input

Possible Causes:



MAP sensor signal circuit shorted to ground (intermittent fault)
 
MAP sensor VREF circuit is open (intermittent fault)
 
MAP sensor is damaged or has failed (intermittent fault)
 
PCM has failed
 

Trouble Code: P1111



IAT Sensor Circuit Intermittent High Input

Possible Causes:



IAT sensor signal circuit is open (intermittent fault)
 
IAT sensor ground circuit is open (intermittent fault)
 
IAT sensor is damaged (an intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1112



IAT Sensor Circuit Intermittent Low Input

Possible Causes:



IAT sensor signal circuit is shorted to ground (intermittent fault)
 
IAT sensor is damaged (an intermittent "shorted" condition)
 
PCM has failed
 

Trouble Code: P1114



ECT Sensor Circuit Intermittent Low Input

Possible Causes:



ECT sensor signal circuit shorted to ground (intermittent fault)
 
ECT sensor has failed (possible intermittent shorted condition)
 
PCM has failed
 

Trouble Code: P1115



ECT Sensor Circuit Intermittent High Input

Possible Causes:



ECT sensor signal circuit is open between the sensor and PCM
 
ECT sensor ground circuit is open between sensor and PCM
 
ECT sensor has failed (possible intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1121



TP Sensor Circuit High Input (Intermittent)

Possible Causes:



TP sensor signal circuit is shorted to VREF (intermittent fault)
 
TP sensor ground circuit is open (an intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent open)
 
PCM has failed
 

Trouble Code: P1122



TP Sensor Circuit Intermittent Low Input

Possible Causes:



TP sensor signal circuit is shorted to ground (intermittent fault)
 
TP sensor VREF circuit is open or grounded (intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent short)
 
PCM has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1153



HO2S-21 (Bank 2 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
MAP sensor or TP sensor is out-of-calibration or "skewed"
 
PCM has failed
 

Trouble Code: P1154



HO2S-21 (Bank 2 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1201



Gas Mass Sensor Range/Performance

Possible Causes:



Air filter or air inlet duct is clogged or restricted
 
Air leaks in the exhaust pipes or manifold, or the HO2S location
 
Base engine problem (i.e., engine compression, vacuum leak)
 
CNG system fuel pressure is incorrect
 
PCV system problem (i.e., PCV vacuum hose or valve leaking)
 
EVAP canister purge system malfunction
 
Gasoline contaminated engine oil
 
Fuel pressure regulator damage or leaking
 
PCM has failed
 

Trouble Code: P1207



FICM PWM Signal To PCM Circuit Malfunction

Possible Causes:



FICM sensor PWM signal circuit is open or shorted to ground
 
FICM is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1215



High Pressure Or Low Pressure Lockout, MIL, NGO Circuit Malfunction

Possible Causes:



Natural Gas Output Enable, High Pressure Lockout, Low Pressure Lockout or MIL control circuit is open, shorted to ground or shorted to system power
 
Alternative Fuels ECU is damaged or has failed
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158ºF (70ºC). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test rpm (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (rpm) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

 
label.common.footer.alt.autozoneLogo