Bonneville, LeSabre, Park Avenue 2000-2005

Crankshaft Position Sensor

Print

Crankshaft Position System Variation Learn Procedure



The crankshaft position system variation compensating values are stored in the PCM non-volatile memory after a learn procedure has been performed. If the actual crankshaft position system variation is not within the crankshaft position system variation compensating values stored in the PCM, DTC P0300 may set. Refer to Diagnostic Aids for DTC P0300. The Crankshaft Position System Variation Learn Procedure should be performed if any of the following conditions are true:



DTC P1336 is set.
 
The PCM has been replaced.
 
The engine has been replaced.
 
The crankshaft has been replaced.
 
The crankshaft harmonic balancer has been replaced.
 
The crankshaft position sensor has been replaced.
 


CAUTION
The scan tool crankshaft position system variation learn function will be inhibited if engine coolant temperature is less than 70C (158F). Allow the engine to warm to at least 70C (158F) before attempting the crankshaft position system variation learn procedure. The scan tool crankshaft position system variation learn function will be inhibited if any Powertrain DTCs other than DTC P1336 are set before or during the crankshaft position system variation learn procedure. Diagnose and repair any DTCs if set. Refer to applicable DTCs. The crankshaft position system variation learn function will be inhibited if the PCM detects a malfunction involving the camshaft position signal circuit, the 3X reference circuit, or the 24X reference circuit. If a malfunction has been indicated, refer to the following list to diagnoses the system or sensor.



DTC P0336 Crankshaft Position (CKP) Sensor Circuit.
 
DTC P0341 Camshaft Position (CMP) Sensor Performance.
 
DTC P1374 Crankshaft Position (CKP) High to Low Resolution Frequency Correlation.
 

The scan tool crankshaft position system variation learn function will not be enabled until engine coolant temperature reaches 158F (70C). Selecting the crankshaft position system variation learn procedure on the scan tool will command the PCM to enable CKP system variation learn fuel cutoff and allow the crankshaft position system variation compensating values to be stored in the PCM. The PCM must detect an engine speed of 5150 RPM (CKP system variation learn fuel cutoff) during the crankshaft position system variation learn procedure to store the crankshaft position system variation compensating values and complete the procedure.


CAUTION
Set the vehicle parking brake and block the drive wheels when performing the Crankshaft Position System Variation Learning Procedure in order to prevent personal injury. Release the throttle when the engine reaches the second fuel cut off. Leaving the throttle open during the fuel cut off will allow the engine to decel at an even rate. Once the learn procedure is completed, the PCM will return the engine control to the operator and the engine will respond to the throttle position.

  1. Set the parking brake.
  2.  
  3. Block the drive wheels.
  4.  
  5. Ensure the hood is closed.
  6.  
  7. Start the engine and allow engine coolant temperature to reach at least 70C (158F).
  8.  
  9. Turn off the ignition switch.
  10.  
  11. Select and enable the crankshaft position variation learn procedure with the scan tool.
  12.  
  13. Start the vehicle.
  14.  
  15. Apply and hold the service brake pedal firmly.
  16.  
  17. Ensure the transaxle is in park.
  18.  
  19. Increase accelerator pedal position and hold until the fuel cutoff is reached at 5150 RPM. Release the accelerator pedal after the second fuel cutoff has been reached.
  20.  
  21. The crankshaft position system variation compensating values are learned when the RPM decreases back to idle. If the procedure terminates.
  22.  
  23. Observe DTC status for DTC P1336.
  24.  
  25. If the scan tool indicates that DTC P1336 ran and passed, the crankshaft position system variation learn procedure is complete. If the scan tool indicates DTC P1336 failed or not run, determine if other DTCs have set. If DTCs other than P1336 are not set, repeat the crankshaft position system variation learn procedure as necessary.
  26.  

Removal & Installation



  1. Turn OFF the ignition.
  2.  
  3. Remove the serpentine belts from the crankshaft pulley.
  4.  
  5. Raise the vehicle.
  6.  
  7. Remove the right front wheel and tire assembly.
  8.  
  9. Remove the right inner fender access cover.
  10.  
  11. Hold the flywheel with a (J 37096) flywheel holding tool.
  12.  
  13. Using 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  14.  
  15. Remove the crankshaft harmonic balancer, using a (J 38197-A) balancer remover.
  16.  
  17. Remove the crankshaft position sensor shield (1). Do not use a pry bar.
  18.  
  19. Disconnect the sensor electrical connector.
  20.  
  21. Remove the attaching bolts from the crankshaft position sensor.
  22.  
  23. Remove the crankshaft position sensor from the block face.
  24.  

To install:

  1. Position the crankshaft position (CKP) sensor to the block.
  2.  
  3. Install the bolts to hold the CKP sensor to the block face. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  4.  
  5. Reinstall the crankshaft position sensor shield.
  6.  
  7. Connect the CKP sensor electrical connector.
  8.  
  9. Position the crankshaft harmonic balancer on the crankshaft.
  10.  
  11. Hold the flywheel with a (J 37096) flywheel holding tool.
  12.  
  13. Using a (J 36660-A) torque/angle meter, tighten the harmonic balancer bolt to 110 ft. lbs. (150 Nm), plus an additional 76 degrees.
  14.  
  15. Install the right inner fender access cover.
  16.  
  17. Install the right front wheel and tire assembly.
  18.  
  19. Tighten the wheel nuts to 104 ft. lbs. (140 Nm.).
  20.  
  21. Lower the vehicle.
  22.  
  23. Reinstall the serpentine belts.
  24.  
  25. Perform the Crankshaft Variation Learn Procedure.
  26.  

 
label.common.footer.alt.autozoneLogo