Camry 2008-2009

Timing Chain & Sprockets 1

Imprimir

Removal & Installation



2.4L Engine

Specific to:

Toyota Camry 2009-2010

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove the crankshaft position sensor plate.

    Click image to see an enlarged view

    Fig. Removing the crankshaft position sensor plate



    Click image to see an enlarged view

    Fig. Removing the bolt and chain tensioner slipper



    Click image to see an enlarged view

    Fig. Removing the two bolts and upper chain vibration damper

  4.  
  5. Remove the bolt and chain tensioner slipper.
  6.  
  7. Remove the two bolts and chain vibration damper.

    Click image to see an enlarged view

    Fig. Removing the bolt and timing chain guide



    Click image to see an enlarged view

    Fig. Removing the upper chain assembly

  8.  
  9. Remove the bolt and timing chain guide.
  10.  
  11. Remove the upper chain assembly.

    Click image to see an enlarged view

    Fig. Removing the crankshaft timing sprocket



    Click image to see an enlarged view

    Fig. Turning the crankshaft by 90°counterclockwise to align the adjusting hole

  12.  
  13. Remove the crankshaft timing sprocket.
  14.  
  15. To remove the lower chain assembly. Turn the crankshaft by 90°counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.

    Click image to see an enlarged view

    Fig. Locking the gear in position

  16.  
  17. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.
  18.  
  19. Remove the bolt, chain tensioner plate and spring.
  20.  
  21. Remove the chain tensioner, oil pump driven sprocket and chain.

    Click image to see an enlarged view

    Fig. Removing the bolt, chain tensioner plate and spring



    Click image to see an enlarged view

    Fig. Removing the chain tensioner, oil pump driven sprocket and chain

  22.  

To install:

  1. Set the crankshaft key into the left horizontal position.
  2.  
  3. Turn the drive shaft so that the cutout faces upward.

    Click image to see an enlarged view

    Fig. Setting the crankshaft key and cutout face



    Click image to see an enlarged view

    Fig. Aligning the yellow mark links with the timing marks of each gear

  4.  
  5. Align the yellow mark links with the timing marks of each gear.
  6.  
  7. Install the sprockets onto the crankshaft and oil pump shaft with the chain wrapped on the gears
  8.  
  9. Temporarily tighten the oil pump drive shaft sprocket with the nut.
  10.  
  11. Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt and tighten to 9 ft. lbs. (12 Nm).

    Click image to see an enlarged view

    Fig. Aligning the adjusting hole of the oil pump drive shaft sprocket

  12.  
  13. Align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.
  14.  
  15. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut to 22 ft. lbs. (30 Nm).

    Click image to see an enlarged view

    Fig. Rotating the crankshaft clockwise by 90°



    Click image to see an enlarged view

    Fig. Installing the crankshaft timing sprocket

  16.  
  17. Rotate the crankshaft clockwise by 90°, and align the crankshaft key to the top.
  18.  
  19. Install the crankshaft timing sprocket.
  20.  
  21. Install the chain vibration damper with the 2 bolts and tighten to 80 inch lbs. (9 Nm).
  22.  
  23. Set the No. 1 cylinder to TDC/compression.

    Click image to see an enlarged view

    Fig. Setting the No. 1 cylinder to TDC/compression

  24.  
  25. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps.
  26.  
  27. Using the crankshaft pulley bolt, turn the crankshaft to position with the key on the crankshaft upward.

    Click image to see an enlarged view