Camry 2008-2009

Throttle Body

Print

Removal & Installation



2.4L Engine

Specific to:

Toyota Camry 2009-2010

  1. Drain engine coolant.
  2.  
  3. Remove No. 1 engine cover sub-assembly.
  4.  
  5. Remove air cleaner cap sub-assembly, as follows:
    1. Disconnect the mass air flow meter connector (1).
    2.  
    3. Disconnect the purge VSV connector (2).
    4.  
    5. Disconnect the 2 purge VSV vacuum hoses (3).
    6.  
    7. Disconnect the purge line hose from the clamp (4).

      Click image to see an enlarged view

      Fig. Remove air cleaner cap sub-assembly

    8.  
    9. Disconnect the No. 2 ventilation hose from the air cleaner hose.
    10.  
    11. Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.
    12.  
    13. Remove the 2 bolts and air cleaner cap.
    14.  
    15. Remove the air cleaner filter element from the air cleaner case.
    16.  

  6.  
  7. Remove air cleaner case sub-assembly.
  8.  
  9. Disconnect the throttle position sensor connector and wire harness clamp.
  10.  
  11. Remove the 4 bolts, and then remove the fuel pipe support and throttle body.

    Click image to see an enlarged view

    Fig. Removing the 4 bolts and fuel pipe support

  12.  
  13. Disconnect the purge line hose from the throttle body.

    Click image to see an enlarged view

    Fig. Disconnecting the purge line hose

  14.  
  15. Disconnect the water by-pass hose from the throttle body.
  16.  
  17. Disconnect the No. 2 water by-pass hose from the throttle body.
  18.  
  19. Disconnect the No. 1 throttle body hose from the throttle body.
  20.  
  21. Remove the gasket from the intake manifold.
  22.  

To install:

  1. Install a new gasket onto the intake manifold.
  2.  
  3. Connect the purge line hose to the throttle body.
  4.  
  5. Connect the water by-pass hose to the throttle body.
  6.  
  7. Connect the No. 2 water by-pass hose to the throttle body.
  8.  
  9. Connect the No. 1 throttle body hose to the throttle body.
  10.  
  11. Install the throttle body and fuel pipe clamp with the 4 bolts and tighten to 22 ft. lbs. (30 Nm).
  12.  
  13. Connect the fuel tube into the clamp.
  14.  
  15. Connect the throttle position sensor connector.
  16.  
  17. Connect the wire harness clamp.
  18.  
  19. Install air cleaner case sub-assembly.
  20.  
  21. Install air cleaner cap sub-assembly, as follows:
    1. Install the air cleaner filter element onto the air cleaner case.
    2.  
    3. Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.
    4.  
    5. Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.
      NOTE
      Make sure that the hose clamp is at the correct angle.

    6.  
    7. Connect the No. 2 ventilation hose to the air cleaner hose.
    8.  
    9. Connect the purge line hose to the clamp.
    10.  
    11. Connect the 2 purge VSV vacuum hoses.
    12.  
    13. Connect the purge VSV connector.
    14.  
    15. Connect the mass air flow meter connector.
    16.  

  22.  
  23. Install air cleaner inlet assembly.
  24.  
  25. Add engine coolant.
  26.  
  27. Check for engine coolant leaks.
  28.  
  29. Install No. 1 engine cover sub-assembly.
  30.  

2.4L Engines

Specific to:

Toyota Camry 2007-2008

  1. Drain engine coolant.
  2.  
  3. Remove No. 1 engine cover sub-assembly.
  4.  
  5. Remove air cleaner cap sub-assembly, as follows:
    1. Disconnect the mass air flow meter connector (1).
    2.  
    3. Disconnect the purge VSV connector (2).
    4.  
    5. Disconnect the 2 purge VSV vacuum hoses (3).
    6.  
    7. Disconnect the purge line hose from the clamp (4).

      Click image to see an enlarged view

      Fig. Remove air cleaner cap sub-assembly

    8.  
    9. Disconnect the No. 2 ventilation hose from the air cleaner hose.
    10.  
    11. Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.
    12.  
    13. Remove the 2 bolts and air cleaner cap.
    14.  
    15. Remove the air cleaner filter element from the air cleaner case.
    16.  

  6.  
  7. Remove air cleaner case sub-assembly.
  8.  
  9. Disconnect the throttle position sensor connector and wire harness clamp.
  10.  
  11. Remove the 4 bolts, and then remove the fuel pipe support and throttle body.

    Click image to see an enlarged view

    Fig. Removing the 4 bolts and fuel pipe support

  12.  
  13. Disconnect the purge line hose from the throttle body.

    Click image to see an enlarged view

    Fig. Disconnecting the purge line hose

  14.  
  15. Disconnect the water by-pass hose from the throttle body.
  16.  
  17. Disconnect the No. 2 water by-pass hose from the throttle body.
  18.  
  19. Disconnect the No. 1 throttle body hose from the throttle body.
  20.  
  21. Remove the gasket from the intake manifold.
  22.  

To install:

  1. Install a new gasket onto the intake manifold.
  2.  
  3. Connect the purge line hose to the throttle body.
  4.  
  5. Connect the water by-pass hose to the throttle body.
  6.  
  7. Connect the No. 2 water by-pass hose to the throttle body.
  8.  
  9. Connect the No. 1 throttle body hose to the throttle body.
  10.  
  11. Install the throttle body and fuel pipe clamp with the 4 bolts and tighten to 22 ft. lbs. (30 Nm).
  12.  
  13. Connect the fuel tube into the clamp.
  14.  
  15. Connect the throttle position sensor connector.
  16.  
  17. Connect the wire harness clamp.
  18.  
  19. Install air cleaner case sub-assembly.
  20.  
  21. Install air cleaner cap sub-assembly, as follows:
    1. Install the air cleaner filter element onto the air cleaner case.
    2.  
    3. Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.
    4.  
    5. Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.
      NOTE
      Make sure that the hose clamp is at the correct angle.

    6.  
    7. Connect the No. 2 ventilation hose to the air cleaner hose.
    8.  
    9. Connect the purge line hose to the clamp.
    10.  
    11. Connect the 2 purge VSV vacuum hoses.
    12.  
    13. Connect the purge VSV connector.
    14.  
    15. Connect the mass air flow meter connector.
    16.  

  22.  
  23. Install air cleaner inlet assembly.
  24.  
  25. Add engine coolant.
  26.  
  27. Check for engine coolant leaks.
  28.  
  29. Install No. 1 engine cover sub-assembly.
  30.  

3.5L Engine

Specific to:

Toyota Camry 2007-2008

  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect battery negative cable.
  4.  
  5. Drain engine coolant.
  6.  
  7. Remove cool air intake duct seal.
  8.  
  9. Remove the V-bank cover sub-assembly.
  10.  
  11. Remove air cleaner inlet assembly.
  12.  
  13. Remove air cleaner cap sub-assembly, as follows:
    1. Disconnect the 3 vacuum hoses.
    2.  
    3. Disconnect the mass air flow meter connector (1).
    4.  
    5. Disconnect the No. 2 ventilation hose (2).
    6.  
    7. Disconnect the hose band (3).

      Click image to see an enlarged view

      Fig. Removing air cleaner cap sub-assembly

    8.  
    9. Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.
    10.  

  14.  
  15. Remove air cleaner case sub-assembly.
  16.  
  17. Remove No. 1 air cleaner inlet.
  18.  
  19. Disconnect the throttle body connector and clamp.

    Click image to see an enlarged view

    Fig. Disconnecting the throttle body connector

  20.  
  21. Disconnect the 2 water by-pass hoses from the throttle body.
  22.  
  23. Remove the 4 bolts and throttle body.
  24.  
  25. Remove the throttle body gasket from the intake air surge tank.

    Click image to see an enlarged view

    Fig. Disconnecting the 2 water by-pass hoses



    Click image to see an enlarged view

    Fig. Removing throttle body bolts

  26.  

To install:

  1. Install a new throttle body gasket to the intake air surge tank.
  2.  
  3. Install the throttle w/ motor body assembly and wire harness clamp stay to the intake air surge tank with the 4 bolts and tighten to 7 ft. lbs. (10 Nm).
  4.  
  5. Connect the throttle w/ motor body assembly connector.
  6.  
  7. Te remainder of installation is the reverse of the removal procedure.
  8.  
  9. Check for coolant leak.
  10.  
  11. Check the function of the throttle body.
  12.  

Specific to:

Toyota Camry 2009-2010

  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect battery negative cable.
  4.  
  5. Drain engine coolant.
  6.  
  7. Remove cool air intake duct seal.
  8.  
  9. Remove the V-bank cover sub-assembly.
  10.  
  11. Remove air cleaner inlet assembly.
  12.  
  13. Remove air cleaner cap sub-assembly, as follows:
    1. Disconnect the 3 vacuum hoses.
    2.  
    3. Disconnect the mass air flow meter connector (1).
    4.  
    5. Disconnect the No. 2 ventilation hose (2).
    6.  
    7. Disconnect the hose band (3).

      Click image to see an enlarged view

      Fig. Removing air cleaner cap sub-assembly

    8.  
    9. Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.
    10.  

  14.  
  15. Remove air cleaner case sub-assembly.
  16.  
  17. Remove No. 1 air cleaner inlet.
  18.  
  19. Disconnect the throttle body connector and clamp.

    Click image to see an enlarged view

    Fig. Disconnecting the throttle body connector

  20.  
  21. Disconnect the 2 water by-pass hoses from the throttle body.
  22.  
  23. Remove the 4 bolts and throttle body.
  24.  
  25. Remove the throttle body gasket from the intake air surge tank.

    Click image to see an enlarged view

    Fig. Disconnecting the 2 water by-pass hoses



    Click image to see an enlarged view

    Fig. Removing throttle body bolts

  26.  

To install:

  1. Install a new throttle body gasket to the intake air surge tank.
  2.  
  3. Install the throttle w/ motor body assembly and wire harness clamp stay to the intake air surge tank with the 4 bolts and tighten to 7 ft. lbs. (10 Nm).
  4.  
  5. Connect the throttle w/ motor body assembly connector.
  6.  
  7. The remainder of installation is the reverse of the removal procedure.
  8.  
  9. Check for coolant leak.
  10.  
  11. Check the function of the throttle body.
  12.  

 
label.common.footer.alt.autozoneLogo