Camry 2008-2009

Removal & Installation

Print

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Drain engine coolant.
  4.  
  5. Remove both front wheel opening extension pads.
  6.  
  7. Remove both engine under cover.
  8.  
  9. For 2.4L and 2.5L engines, perform the following:
    1. Remove air cleaner cap sub-assembly.
    2.  
    3. Remove air cleaner inlet assembly.
    4.  

  10.  
  11. For 3.5L engines, perform the following:
    1. Remove v-bank cover sub-assembly.
    2.  
    3. Remove cool air intake duct seal.
    4.  
    5. Remove air cleaner cap sub-assembly.
    6.  
    7. Remove air cleaner inlet sub-assembly.
    8.  
    9. Remove no. 1 air cleaner inlet.
    10.  

  12.  
  13. For all vehicles, remove front bumper assembly.
  14.  
  15. Remove front bumper energy absorber.
  16.  
  17. Separate the radiator reserve tank hose from the radiator assembly.
  18.  
  19. Disconnect the inlet and outlet radiator hose from the radiator assembly.
  20.  
  21. Disconnect the oil from the radiator assembly.
  22.  
  23. For vehicles with A/T, disconnect the oil cooler inlet hose and outlet hose from the radiator assembly.
  24.  
  25. For 2.5L engines, remove the hood lock assembly.
  26.  
  27. Remove the upper radiator support, as follows:
    1. Disconnect the horn connector.
    2.  
    3. Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.
    4.  
    5. Remove the clamp and separate the hood lock control cable from the radiator support upper.
    6.  
    7. Remove the 5 bolts and radiator support upper.

      Click image to see an enlarged view

      Fig. Removing 5 bolts and upper radiator support

    8.  

  28.  
  29. Remove the radiator assembly, as follows:
    1. Remove the 3 clamps and 2 connectors.
    2.  
    3. Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
    4.  
    5. Remove the radiator assembly from the body by pulling upwards.

      Click image to see an enlarged view

      Fig. Removing 4 bolts and separating the condenser assembly

    6.  

  30.  
  31. Release the 3 snap fits and lift the fan assembly with motor from the radiator.
  32.  
  33. Remove the 2 radiator support cushions from the radiator assembly.
  34.  
  35. Remove the 2 radiator support lowers from the radiator assembly.

    Click image to see an enlarged view

    Fig. Remove the 2 radiator support cushions

  36.  

To install:

  1. Installation is the reverse of removal.
  2.  
  3. After installation, inspect for coolant leak.
  4.  

Except Hybrid



Specific to:

Toyota Camry 2007-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Drain engine coolant.
  4.  
  5. Remove both front wheel opening extension pads.
  6.  
  7. Remove both engine under cover.
  8.  
  9. For 2.4L engines, perform the following:
    1. Remove air cleaner cap sub-assembly.
    2.  
    3. Remove air cleaner inlet assembly.
    4.  

  10.  
  11. For 3.5L engines, perform the following:
    1. Remove v-bank cover sub-assembly.
    2.  
    3. Remove cool air intake duct seal.
    4.  
    5. Remove air cleaner cap sub-assembly.
    6.  
    7. Remove air cleaner inlet sub-assembly.
    8.  
    9. Remove no. 1 air cleaner inlet.
    10.  

  12.  
  13. For all vehicles, remove front bumper assembly.
  14.  
  15. Remove front bumper energy absorber.
  16.  
  17. Separate the radiator reserve tank hose from the radiator assembly.
  18.  
  19. Disconnect the inlet and outlet radiator hose from the radiator assembly.
  20.  
  21. Disconnect the oil from the radiator assembly.
  22.  
  23. For vehicles with A/T, disconnect the oil cooler inlet hose and outlet hose from the radiator assembly.
  24.  
  25. Remove the upper radiator support, as follows:
    1. Disconnect the horn connector.
    2.  
    3. Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.
    4.  
    5. Remove the clamp and separate the hood lock control cable from the radiator support upper.
    6.  
    7. Remove the 5 bolts and radiator support upper.

      Click image to see an enlarged view

      Fig. Removing 5 bolts and upper radiator support

    8.  

  26.  
  27. Remove the radiator assembly, as follows:
    1. Remove the 3 clamps and 2 connectors.
    2.  
    3. Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
    4.  
    5. Remove the radiator assembly from the body by pulling upwards.

      Click image to see an enlarged view

      Fig. Removing 4 bolts and separating the condenser assembly

    6.  

  28.  
  29. Release the 3 snap fits and lift the fan assembly with motor from the radiator.
  30.  
  31. Remove the 2 radiator support cushions from the radiator assembly.
  32.  
  33. Remove the 2 radiator support lowers from the radiator assembly.

    Click image to see an enlarged view

    Fig. Remove the 2 radiator support cushions

  34.  

To install:

  1. Installation is the reverse of removal.
  2.  
  3. After installation, inspect for coolant leak.
  4.  

Hybrid Models



Specific to:

Toyota Camry 2007-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Drain engine coolant.
  4.  
  5. Remove the both front wheel opening extension pads.
  6.  
  7. Remove the both engine under cover.
  8.  
  9. Remove the air cleaner cap sub-assembly.
  10.  
  11. Remove the air cleaner inlet assembly.
  12.  
  13. Remove the front bumper assembly.
  14.  
  15. Remove the front bumper energy absorber.
  16.  
  17. Separate the radiator reserve tank hose from the radiator assembly.
  18.  
  19. Disconnect the inlet and outlet radiator hose from the radiator assembly.
  20.  
  21. Disconnect the oil from the radiator assembly.
  22.  
  23. Disconnect the oil cooler inlet hose and outlet hose from the radiator assembly.
  24.  
  25. Remove the upper radiator support, as follows:
    1. Disconnect the horn connector.
    2.  
    3. Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.
    4.  
    5. Remove the clamp and separate the hood lock control cable from the radiator support upper.
    6.  
    7. Remove the 5 bolts and radiator support upper.

      Click image to see an enlarged view

      Fig. Removing 5 bolts and upper radiator support

    8.  

  26.  
  27. Remove the radiator assembly, as follows:
    1. Remove the 3 clamps and 2 connectors.
    2.  
    3. Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
    4.  
    5. Remove the radiator assembly from the body by pulling upwards.

      Click image to see an enlarged view

      Fig. Removing 4 bolts and separating the condenser assembly

    6.  

  28.  
  29. Release the 3 snap fits and lift the fan assembly with motor from the radiator.
  30.  
  31. Remove the 2 radiator support cushions from the radiator assembly.
  32.  
  33. Remove the 2 radiator support lowers from the radiator assembly.

    Click image to see an enlarged view

    Fig. Remove the 2 radiator support cushions

  34.  

To install:

  1. Installation is the reverse of removal.
  2.  
  3. Install engine coolant and bleed the cooling system.
  4.  
  5. After installation, inspect for coolant leak.
  6.  

 
label.common.footer.alt.autozoneLogo