Canyon, Colorado 2006-2007

Window Systems

Print

Door Glass & Regulator



Power Windows
Diagnosis & Testing

The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located. Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.

Removal & Installation
Window Motor & Regulator

CAUTION
Do not attempt to service the regulator motor without releasing the counterbalance spring tension. The regulator lift arm is under tension from the counterbalance spring and can cause personal injury if the motor is removed from the regulator.

Front
  1. Remove the front door trim panel.
  2.  
  3. Remove the front door water deflector.
  4.  
  5. Remove the bolts retaining the front door window to the window regulator.
  6.  
  7. Remove the front door window.
  8.  
  9. Disconnect the electrical connector from the window regulator motor, if equipped with A31.
  10.  
  11. Loosen the bolts retaining the window regulator to the inner panel at the keyhole slot locations.
  12.  
  13. Remove the remaining fasteners retaining the window regulator to the inner panel.
  14.  
  15. Remove the window regulator from the door by lifting the regulator up, and out of the keyhole slots, and removing the regulator out through the access hole.
  16.  
  17. Drill a hole through the window regulator bracket and lift arm.
  18.  
  19. Install a nut and bolt through the hole to secure the lift arm while the motor is removed.
  20.  
  21. Remove the bolts retaining the front window regulator motor to the regulator bracket.
  22.  
  23. Remove the front window regulator motor from the regulator.
  24.  

To install:

  1. Install the front window regulator motor to the regulator.
  2.  
  3. Install the bolts retaining the front window regulator motor to the regulator bracket. Tighten the front window regulator motor bolts to 40 inch lbs (4.5 Nm).
  4.  
  5. Remove the nut and bolt securing the lift arm to the regulator bracket.
  6.  
  7. Install the front door window regulator into the front door through the access hole.
  8.  
  9. Position the window regulator to the inner panel by sliding the regulator bolts into the keyhole slots in the inner panel.
  10.  
  11. Install the fastener retaining the front door window regulator to the door. Tighten the front window regulator fasteners to 80 inch lbs (9 Nm).
  12.  
  13. Connect the electrical connector to the window regulator motor, if equipped with A31.
  14.  
  15. Install the front door window.
  16.  
  17. Install the bolts retaining the window to the window regulator. Tighten the front window regulator fasteners to 80 inch lbs (9 Nm).
  18.  
  19. Install the front door water deflector.
  20.  
  21. Install the front door trim panel.
  22.  

Rear
  1. Remove the rear door trim panel.
  2.  
  3. Remove the rear inside door handle.
  4.  
  5. Remove the rear door speaker.
  6.  
  7. Remove the rear door water deflector.
  8.  
  9. Remove the bolts retaining the rear window to the window regulator.
  10.  
  11. Raise and support the rear door window.
  12.  
  13. Disconnect the electrical connector from the window regulator motor, if equipped with A31.
  14.  
  15. Loosen the bolts retaining the window regulator to the inner door at the keyhole slot locations.
  16.  
  17. Remove the bolts retaining the window regulator to the inner panel.
  18.  
  19. Remove the window regulator by lifting the regulator up, and out of the keyhole slots in the inner panel, and removing the regulator out through the access hole.
  20.  
  21. Remove the bolts retaining the rear window regulator motor to the regulator bracket.
  22.  
  23. Remove the rear window regulator motor from the regulator.
  24.  

To install:

  1. Install the rear window regulator motor to the regulator.
  2.  
  3. Install the bolts retaining the rear window regulator motor to the regulator bracket. Tighten the rear window regulator motor bolts to 40 inch lbs (4.5 Nm).
  4.  
  5. Install the rear door window regulator (1) into the rear door through the access hole.
  6.  
  7. Position the rear door window regulator to the inner panel by inserting the regulator bolts to the keyhole slots (2) on the inner panel.
  8.  
  9. Install the bolts retaining the rear door window regulator to the inner panel.
  10.  
  11. Tighten the rear window regulator bolts to 80 inch lbs (9 Nm).
  12.  
  13. Connect the electrical connector to the window regulator motor, if equipped with A31.
  14.  
  15. Remove the window support and lower the window onto the window regulator carrier plate.
  16.  
  17. Install the bolts retaining the window to the window regulator. Tighten the rear window regulator bolts to 80 inch lbs (9 Nm).
  18.  
  19. Install the rear door water deflector.
  20.  
  21. Install the rear door speaker.
  22.  
  23. Install the rear door inside handle.
  24.  
  25. Install the rear door trim panel.
  26.  

Window Switch
  1. Remove the 2 screws securing the switch plate assembly to the door trim panel.
  2.  
  3. Lift the front of the switch plate up to disengage clip.
  4.  
  5. Remove the switch plate out of the door trim panel opening.
  6.  
  7. Disconnect the electrical connectors from the switches.
  8.  
  9. Remove the switch plate assembly from the vehicle.
  10.  
  11. If replacing only the switches, remove the switches from the plate.
  12.  
  13. If replacing only the switch plate, retain the switches for transfer.
  14.  
  15. To install, reverse removal procedure.
  16.  

 
label.common.footer.alt.autozoneLogo