Caravan, Town & Country 2006-2007

Blower Motor

Print

Removal & Installation



  1. Disconnect and isolate the negative battery cable.
  2.  
  3. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2.  
    3. Remove the sliding door sill plate.
    4.  
    5. Remove the quarter trim bolster.
    6.  
    7. Remove the upper C-pillar trim and D-pillar trim panel.
    8.  
    9. Remove the first and second rear seat belt anchors.
    10.  
    11. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    12.  
    13. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    14.  
    15. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      Click image to see an enlarged view

      Fig. Removing the trim panel to access the rear blower motor

    16.  
    17. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    18.  
    19. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    20.  
    21. Pull first rear seat belt through the access hole.
    22.  
    23. Remove the quarter trim panel from the vehicle.
    24.  

  4.  
  5. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  6.  
  7. Twist the blower motor out of scroll housing.
  8.  
  9. Disconnect the blower motor wiring connector.
  10.  
  11. Remove the blower motor from vehicle.

    Click image to see an enlarged view

    Fig. The rear blower motor is held in place by four screws

  12.  

To install:

  1. Install the blower motor unit into the vehicle.
  2.  
  3. Reconnect the blower motor wiring connector.
  4.  
  5. Secure the blower motor into scroll housing.
  6.  
  7. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  8.  
  9. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2.  
    3. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    4.  
    5. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    6.  
    7. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    8.  
    9. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    10.  
    11. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    12.  
    13. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    14.  
    15. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    16.  
    17. Install the D-pillar trim panel and upper C-pillar trim.
    18.  
    19. Install the quarter trim bolster.
    20.  
    21. Install the sliding door sill plate.
    22.  
    23. Install the second rear seat, if equipped, and install the first rear seat.
    24.  

  10.  
  11. Reconnect the negative battery cable. Check blower motor operation.
  12.  

  1. Disconnect and isolate the negative battery cable.
  2.  
  3. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2.  
    3. Remove the sliding door sill plate.
    4.  
    5. Remove the quarter trim bolster.
    6.  
    7. Remove the upper C-pillar trim and D-pillar trim panel.
    8.  
    9. Remove the first and second rear seat belt anchors.
    10.  
    11. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    12.  
    13. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    14.  
    15. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      Click image to see an enlarged view

      Fig. Removing the trim panel to access the rear blower motor

    16.  
    17. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    18.  
    19. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    20.  
    21. Pull first rear seat belt through the access hole.
    22.  
    23. Remove the quarter trim panel from the vehicle.
    24.  

  4.  
  5. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  6.  
  7. Twist the blower motor out of scroll housing.
  8.  
  9. Disconnect the blower motor wiring connector.
  10.  
  11. Remove the blower motor from vehicle.

    Click image to see an enlarged view

    Fig. The rear blower motor is held in place by four screws

  12.  

To install:

  1. Install the blower motor unit into the vehicle.
  2.  
  3. Reconnect the blower motor wiring connector.
  4.  
  5. Secure the blower motor into scroll housing.
  6.  
  7. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  8.  
  9. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2.  
    3. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    4.  
    5. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    6.  
    7. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    8.  
    9. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    10.  
    11. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    12.  
    13. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    14.  
    15. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    16.  
    17. Install the D-pillar trim panel and upper C-pillar trim.
    18.  
    19. Install the quarter trim bolster.
    20.  
    21. Install the sliding door sill plate.
    22.  
    23. Install the second rear seat, if equipped, and install the first rear seat.
    24.  

  10.  
  11. Reconnect the negative battery cable. Check blower motor operation.
  12.  

 
label.common.footer.alt.autozoneLogo