Caravan, Town & Country 2006-2007

Alternator

Print

Diagnosis & Testing



Load Test
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. With the engine running, turn on the blower motor and the high beams (or other electrical accessories to place a load on the charging system).
  4.  
  5. Increase and hold engine speed to 2000 rpm.
  6.  
  7. Measure the voltage reading at the battery.
  8.  
  9. The voltage should increase at least 0.5 volts from the voltage test. If the voltage does not meet specifications, the charging system is malfunctioning.
    NOTE
    Usually under and overcharging is caused by a defective alternator, or its related parts (regulator), and replacement will fix the problem; however, faulty wiring and other problems can cause the charging system to malfunction. Many automotive parts stores have alternator bench testers available for use by customers. An alternator bench test is the most definitive way to determine the condition of your alternator.

  10.  

No Load Test
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Connect a tachometer to the engine.
    CAUTION
    Ensure that the transmission is in Park and the emergency brake is set. Blocking a wheel is optional and an added safety measure.

  4.  
  5. Turn off all electrical loads (radio, blower motor, wipers, etc.)
  6.  
  7. Start the engine and increase engine speed to approximately 1500 rpm.
  8.  
  9. Measure the voltage reading at the battery with the engine holding a steady 1500 rpm. Voltage should have raised at least 0.5 volts, but no more than 2.5 volts.
  10.  
  11. If the voltage does not go up more than 0.5 volts, the alternator is not charging. If the voltage goes up more than 2.5 volts, the alternator is overcharging.
    NOTE
    Usually under and overcharging is caused by a defective alternator, or its related parts (regulator), and replacement will fix the problem; however, faulty wiring and other problems can cause the charging system to malfunction. Many automotive parts stores have alternator bench testers available for use by customers. An alternator bench test is the most definitive way to determine the condition of your alternator.

  12.  
  13. If the voltage is within specifications, proceed to the next test.
  14.  

Voltage Test
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Make sure the engine is OFF , and turn the headlights on for 15-20 seconds to remove any surface charge from the battery.
  4.  
  5. Using a DVOM set to volts DC, probe across the battery terminals.
  6.  
  7. Measure the battery voltage.
  8.  
  9. Write down the voltage reading and proceed to the next test.
  10.  

Removal & Installation



2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Air inlet temperature sensor connector
     
    Air cleaner assembly
     
    Evaporative emissions (EVAP) purge solenoid from the bracket and position aside
     
    Alternator harness connections
     
    Accessory drive belt
     
    Alternator
     

  4.  

To install:

  1. Install or connect the following:

    Alternator
     
    Accessory drive belt. Tighten the alternator mounting fasteners to 20 ft. lbs. (28 Nm).
     
    Alternator harness connections
     
    EVAP purge solenoid
     
    Air cleaner assembly
     
    Air inlet temperature sensor connector
     
    Negative battery cable
     

  2.  

3.0L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Wiper module
     
    Accessory drive belt
     
    Alternator mounting bolts
     
    Alternator harness connectors
     
    Alternator
     

  4.  

To install:

  1. Install or connect the following:

    Alternator
     
    Alternator harness connectors
     
    Alternator mounting bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
     
    Accessory drive belt
     
    Wiper module
     
    Negative battery cable
     

  2.  

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Alternator harness connectors
     
    Right front lower splash shield
     
    Accessory drive belt
     
    Lower oil dipstick tube bolt and the wiring harness from the tube
     
    3 mounting bolts
     
    Dipstick tube
     
    Alternator
     

  4.  

To install:

  1. Install or connect the following:

    Alternator in position and the 3 mounting bolts. Tighten to 40 ft. lbs. (54 Nm).
     
    Dipstick tube, lubricate the O-ring with clean engine oil prior to installation, then tighten the upper dipstick tube bolt.
     
    Alternator harness connectors
     
    Lower oil dipstick tube bolt
     
    Accessory drive belt
     
    Right front lower splash shield
     
    Wiring harness to the dipstick tube
     
    Negative battery cable
     

  2.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Alternator harness connectors
     
    Right front lower splash shield
     
    Accessory drive belt
     
    Lower oil dipstick tube bolt and the wiring harness from the tube
     
    3 mounting bolts
     
    Dipstick tube
     
    Alternator
     

  4.  

To install:

  1. Install or connect the following:

    Alternator in position and the 3 mounting bolts. Tighten to 40 ft. lbs. (54 Nm).
     
    Dipstick tube, lubricate the O-ring with clean engine oil prior to installation, then tighten the upper dipstick tube bolt.
     
    Alternator harness connectors
     
    Lower oil dipstick tube bolt
     
    Accessory drive belt
     
    Right front lower splash shield
     
    Wiring harness to the dipstick tube
     
    Negative battery cable
     

  2.  

 
label.common.footer.alt.autozoneLogo