Century, Grand Prix, Impala, Intrigue, Lumina, Monte Carlo, Regal 2001-2005

3.5L V6 VIN H Auto 3

Print

Trouble Code: P1114



ECT Sensor Circuit Intermittent Low Input

Possible Causes:



ECT sensor signal circuit shorted to ground (intermittent fault)
 
ECT sensor has failed (possible intermittent shorted condition)
 
PCM has failed
 

Trouble Code: P1115



ECT Sensor Circuit Intermittent High Input

Possible Causes:



ECT sensor signal circuit is open between the sensor and PCM
 
ECT sensor ground circuit is open between sensor and PCM
 
ECT sensor has failed (possible intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1121



TP Sensor Circuit Intermittent High Input

Possible Causes:



TP sensor connector is damaged, loose or open
 
TP sensor signal circuit is shorted to VREF (intermittent fault)
 
TP sensor ground circuit is open (an intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent open)
 
PCM has failed
 

Trouble Code: P1122



TP Sensor Circuit Intermittent High Input

Possible Causes:



TP sensor signal circuit is shorted to ground (intermittent fault)
 
TP sensor VREF circuit is open or grounded (intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent short)
 
PCM has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158ºF (70ºC). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test rpm (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (rpm) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

Trouble Code: P1351



ICM Ignition Control Circuit High Input

Possible Causes:



ICM control circuit is open
 
ICM low reference (ground) circuit has high resistance condition
 
ICM is damaged or has failed
 
PCM has failed
 

Trouble Code: P1352



Ignition Control Bypass Circuit High Input

Possible Causes:



ICM timing signal circuit is open
 
ICM unit is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1361



ICM Ignition Control Circuit Low Input

Possible Causes:



IC timing control circuit is shorted to ground or shorted to power
 
IC module has failed
 
PCM has failed
 

Trouble Code: P1441



EVAP System Flow During Non-Purge

Possible Causes:



EVAP purge valve, purge pipe, or the charcoal canister has a temporary blockage (this fault could cause an intermittent fault)
 
FTP sensor is out-of-calibration, damaged or it is skewed
 
EVAP purge solenoid valve is damaged or has failed
 
PCM has failed
 

Trouble Code: P1814



Torque Converter Overstressed (4T65-E, 4T80-E)

Possible Causes:



ATF level is low or the fluid is burnt or contaminated
 
ATF filter is clogged or not properly installed/seated
 
Vehicle used for towing or driven while overloaded
 

Trouble Code: U1000



Class 2 Communication Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
SDM (module) could be shorted pulling the voltage low
 

Trouble Code: U1016



No Communication With Powertrain Control Module

Possible Causes:



PCM Class 2 circuit is open, shorted to ground or to B+
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
PCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1048



No Communication With Rear Wheel Steering Control Module

Possible Causes:



RWSCM Class 2 circuit is open, shorted to ground or to B+
 
RWSCM ignition power circuit has a high resistance condition
 
RESCM main ground circuit(s) has a high resistance condition
 
RESCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1064



No Communication With Body Control Module

Possible Causes:



BCM Class 2 circuit is open, shorted to ground or to B+
 
BCM ignition power circuit has a high resistance condition
 
BCM main ground circuit(s) has a high resistance condition
 
BCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1088



No Communication With SDM (Restraint Module)

Possible Causes:



SDM Class 2 circuit is open, shorted to ground or to B+
 
SDM ignition power circuit has a high resistance condition
 
SDM main ground circuit(s) has a high resistance condition
 
SDM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1096



No Communication With Instrument Panel Cluster

Possible Causes:



IPC Class 2 circuit is open, shorted to ground or to B+
 
IPC ignition power circuit has a high resistance condition
 
IPC main ground circuit(s) has a high resistance condition
 
IPC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1097



No Communication With Driver Information Center

Possible Causes:



DIC Class 2 circuit is open, shorted to ground or to B+
 
DIC ignition power circuit has a high resistance condition
 
DIC main ground circuit(s) has a high resistance condition
 
DIC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1151



No Communication With Vehicle Interface Unit

Possible Causes:



VIU Class 2 circuit is open, shorted to ground or to B+
 
VIU ignition power circuit has a high resistance condition
 
VIU main ground circuit(s) has a high resistance condition
 
VIU (module) may have failed and is pulling the circuit low
 

Trouble Code: U1152



No Communication With HVAC Control Module

Possible Causes:



HVAC Class 2 circuit is open, shorted to ground or to B+
 
HVAC ignition power circuit has a high resistance condition
 
HVAC main ground circuit(s) has a high resistance condition
 
HVAC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1255



Class 2 Communications Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 

Trouble Code: U1305



Class 2 Data Link High or Low

Possible Causes:



Class 2 serial data line has either a high or low voltage condition on the circuit, and the module cannot identify the fault
 
One or more modules on Class 2 line has an short to power
 
One or more modules on the Class 2 line has a short to ground
 

 
label.common.footer.alt.autozoneLogo