Cherokee, Grand Cherokee, 1999-2005

4.0L L6 VIN S Std 4

Print

Trouble Code: P0731



A/T Additional Gear Ratio Error In First Gear

Possible Causes:



U/D and 2/4 pressures less than 105 psi
 
U/D or L/R clutch volume indexes out of specification
 
L/R accumulator seals are damaged or L/R switch valve stuck
 
L/R switch valve stuck in first gear position
 
Transmission has an internal leak (U/D or other seals leaking)
 

Trouble Code: P0732



A/T Additional Gear Ratio Error In Second Gear

Possible Causes:



U/D and L/R pressures less than 95 psi at 2000 rpm
 
U/D or 2/4 clutch volume indexes out of specification
 
L/R accumulator seals are damaged or L/R switch valve stuck
 
Transmission has an internal leak (U/D or 2/4 seals leaking)
 
L/R switch valve stuck in first gear position
 

Trouble Code: P0733



A/T Additional Gear Ratio Error In Third Gear

Possible Causes:



O/D and U/D pressures less than 75 psi
 
O/D or U/D clutch volume indexes out of specification
 
O/D accumulator seals are damaged
 
L/R switch valve stuck in first gear position
 
Transmission has an internal leak (U/D seals leaking)
 

Trouble Code: P0734



A/T Additional Gear Ratio Error In Fourth Gear

Possible Causes:



Customer may complain of intermittent 4th gear operation
 
O/D and 2/4 pressures less than 75 psi
 
O/D or 2/4 clutch volume indexes out of specification
 
O/D accumulator seals are damaged
 
Transmission enters "limp in" mode running in 4th gear
 

Trouble Code: P0735



A/T Gear Ratio Error Fourth Prime

Possible Causes:



Related Gear Ratio trouble codes may be stored (note that some of these Gear Ratio trouble codes may be intermittent)
 
Transmission has internal problems or damage present
 

Trouble Code: P0736



A/T Additional Gear Ratio Error In Reverse Gear

Possible Causes:



Customer may complain of intermittent Reverse gear operation
 
Related Gear Ratio trouble codes may be stored
 
Transmission has internal problems or damage present
 

Trouble Code: P0740



A/T Torque Converter Clutch - No RPM Drop At Lockup

Possible Causes:



Internal transmission component fault (Input or Reaction shaft)
 
Internal transmission leakage (valve body leaking or seal rings)
 
Converter clutch valve or clutch timing valve is sticking
 
TCC assembly has failed
 

Trouble Code: P0743



A/T Torque Converter Clutch Solenoid Circuit Failure

Possible Causes:



TCC power circuit is open between the solenoid and Fused B+
 
TCC solenoid control circuit is open or shorted to ground
 
TCC solenoid control circuit is shorted to system power
 
TCC solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0748



A/T Governor Pressure Solenoid/Transmission Relay Fault

Possible Causes:



A/T transmission relay power circuit is open (test power to B+)
 
A/T transmission relay is damaged or has failed
 
Governor pressure solenoid circuit is open or shorted to ground
 
Governor pressure solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0750



A/T Low/Reverse Solenoid Circuit Failure

Possible Causes:



L/R solenoid control circuit is open or shorted to ground
 
L/R solenoid control circuit is shorted to system power
 
L/R Solenoid is damaged or has failed
 
TCM or PCM has failed
 

Trouble Code: P0751



A/T Overdrive Switch Pressed Low For Over 5 Minutes

Possible Causes:



Overdrive Switch Off" circuit is shorted to ground
 
Overdrive Switch is damaged or has failed
 
PCM has failed
 

Trouble Code: P0753



A/T 3-4 Solenoid/Transmission Relay Circuit Failure

Possible Causes:



3-4 Solenoid control circuit is open or shorted to ground
 
3-4 Solenoid is damaged or has failed
 
Transmission relay power circuit is open (check the fused B+)
 
Transmission relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P0755



A/T 2/4 Solenoid Circuit Failure

Possible Causes:



2/4 Solenoid control circuit is open or shorted to ground
 
2/4 Solenoid control circuit is shorted to system power
 
2/4 Solenoid is damaged or has failed
 
TCM or PCM has failed
 

Trouble Code: P0756



A/T Shift Solenoid 'B' Mechanical Failure

Possible Causes:



ATF level is low, or the ATF fluid is contaminated
 
A/T SSB is damaged (mechanical fault) or has failed
 
Automatic transmission has internal damage or has failed
 

Trouble Code: P0760



A/T Overdrive Solenoid Circuit Failure

Possible Causes:



O/D Solenoid control circuit is open, shorted to ground or power
 
O/D Solenoid is damaged or has failed
 
TCM relay power circuit to O/D solenoid is open (loss of B+)
 
TCM or PCM has failed
 

Trouble Code: P0765



A/T Underdrive Solenoid Circuit Malfunction

Possible Causes:



U/D Solenoid control circuit is open or shorted to ground
 
U/D Solenoid control circuit is shorted to system power
 
U/D Solenoid is damaged or has failed
 
TCM or PCM has failed
 

Trouble Code: P0783



A/T 3-4 Shift Solenoid - No RPM Drop At Lockup

Possible Causes:



ATF fluid level is burnt, contaminated or low
 
3-4 Solenoid control circuit is open or shorted (intermittent fault)
 
3-4 Solenoid is damaged or has failed
 
Transmission oil pan has excessive debris
 

Trouble Code: P0841



Low/Reverse Pressure Switch Sense Circuit Malfunction

Possible Causes:



L/R pressure switch sense circuit is open or shorted to ground
 
L/R pressure switch sense circuit is shorted to power (B+)
 
L/R pressure switch is damaged or it has failed
 
TCM relay power circuit to L/R switch is open (loss of B+)
 
TCM has failed
 

Trouble Code: P0845



A/T 2/4 Hydraulic Pressure Test Malfunction

Possible Causes:



2/4 pressure is incorrect, or internal transmission faults exist
 
2/4 pressure switch circuit is open, shorted to ground or power
 
2/4 pressure switch is damaged or it has failed
 
Transmission solenoids/TRS assembly is damaged or have failed
 
TCM relay power circuit to 2/4 switch is open (loss of B+)
 
Intermittent wiring or connector problems exist
 
PCM or TCM has failed
 

Trouble Code: P0846



A/T 2/4 Pressure Switch Circuit Malfunction

Possible Causes:



2/4 pressure is incorrect, or internal transmission faults exist
 
2/4 pressure switch circuit is open, shorted to ground or power
 
2/4 pressure switch is damaged or it has failed
 
TCM relay power circuit to L/R switch is open (loss of B+)
 
PCM/TCM has failed
 

Trouble Code: P0850



A/T Park/Neutral Switch Performance

Possible Causes:



Check for any TCM related codes stored in the TCM controller
 
PCM has failed
 

Trouble Code: P0891



A/T TCM Relay Always On

Possible Causes:



TCM relay output circuit is shorted to system power (B+)
 
TCM relay control circuit is shorted to system power (B+)
 
TCM relay is damaged or it has failed (it may be stuck closed)
 
Intermittent wiring or connector problems exist
 
PCM/TCM has failed
 

Trouble Code: P0897



A/T Transmission Fluid Burnt Or Worn Out

Possible Causes:



Automatic transmission fluid is burnt or contaminated
 
Automatic transmission fluid is worn out
 

Trouble Code: P0951



A/T AutoStick Sensor Circuit Malfunction

Possible Causes:



AutoStick assembly is damaged or has failed
 
AutoStick connector is damaged, loose or shorted
 
Downshift switch circuit is shorted too ground
 
Upshift switch circuit is shorted to ground
 

Trouble Code: P0992



A/T 2/4 & O/D Hydraulic Pressure Test Malfunction

Possible Causes:



2/4 pressure switch circuit is open, shorted to ground or power
 
2/4 pressure switch is damaged or it has failed
 
O/D pressure switch circuit is open, shorted to ground or power
 
O/D pressure switch is damaged or it has failed
 
Internal transmission faults exist
 
TCM relay power circuit to 2/4 or O/D switch open (loss of B+)
 
PCM/TCM has failed
 

Trouble Code: P1192



Intake Air Temperature Sensor Circuit Low Input

Possible Causes:



IAT Sensor signal circuit is shorted to ground
 
IAT Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1193



Intake Air Temperature Sensor Circuit High Input

Possible Causes:



IAT Sensor connector is damaged or it is open
 
IAT Sensor signal circuit is open between the Sensor and PCM
 
IAT Sensor ground circuit is open between the Sensor and PCM
 
IAT Sensor damaged or has failed
 
PCM has failed
 

Trouble Code: P1195



O2 (B1 S1) Circuit Insufficient Activity

Possible Causes:



Base engine mechanical fault affecting more than one cylinder
 
Exhaust leak present in exhaust manifold or exhaust pipes
 
O2 element fuel contamination or has deteriorated
 
O2 signal circuit or ground circuit has high resistance
 
PCM has failed
 

Trouble Code: P1196



O2 (B2 S1) Circuit Insufficient Activity

Possible Causes:



Base engine mechanical fault affecting more than one cylinder
 
Exhaust leak present in exhaust manifold or exhaust pipes
 
O2 element fuel contamination or has deteriorated
 
O2 signal circuit or ground circuit has high resistance
 

Trouble Code: P1281



Engine Is Cold Too Long

Possible Causes:



Check the operation of the thermostat (it may be stuck open)
 
ECT Sensor signal circuit has high resistance
 
ECT Sensor is damaged or it has failed
 
Inspect for low coolant level or an incorrect coolant mixture
 

Trouble Code: P1282



Fuel Pump Relay Control Circuit Malfunction

Possible Causes:



Fuel pump relay control circuit is open or shorted to ground
 
Fuel pump relay power circuit is open (test power from Ignition)
 
Fuel pump relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1289



Manifold Tuning Valve Control Circuit Malfunction

Possible Causes:



MTV control circuit is open between the solenoid and PCM
 
MTV control circuit is shorted to Sensor or chassis ground
 
MTV is damaged or has failed
 
PCM has failed
 

Trouble Code: P1294



Target Idle Speed Not Reached

Possible Causes:



Engine vacuum leak in a hose, brake booster or in the engine
 
IAC motor control circuits open or grounded in the wire harness
 
Throttle body dirty or restricted (trying cleaning it and retesting)
 
Throttle linkage or throttle plate not in the correct position
 
PCM has failed
 

Trouble Code: P1296



5-Volt VREF Supply Not Present

Possible Causes:



MAP Sensor VREF circuit open between the Sensor and PCM
 
MAP Sensor ground circuit open between the Sensor and PCM
 
MAP Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1297



No Change In MAP Signal From Start To Run Transition

Possible Causes:



Engine vacuum port to MAP Sensor clogged, dirty or restricted
 
MAP Sensor signal is skewed or the Sensor is out-of-calibration
 
MAP Sensor VREF circuit open or grounded (intermittent fault)
 
PCM has failed
 

Trouble Code: P1299



Vacuum Leak Present With IAC Valve Fully Seated

Possible Causes:



Leaking engine vacuum hose, brake booster, or in the engine
 
MAP Sensor is out-of-calibration or skewed
 
TP Sensor is damaged or has failed (perform a sweep test)
 
PCM has failed
 

Trouble Code: P1388



Auto Shutdown Relay Control Circuit Malfunction

Possible Causes:



ASD relay control circuit is open between the relay and PCM
 
ASD relay control circuit is shorted to ground
 
ASD relay power circuit is open (test power from Fused B+)
 
ASD relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1389



No Auto Shutdown Relay Output Voltage To PCM

Possible Causes:



ASD relay connector is damaged, loose or shorted
 
ASD relay output circuit is open between the relay and PCM
 
ASD relay power circuit is open (test power from Fused B+)
 
ASD relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1390



Timing Belt Skipped One Tooth Or More

Possible Causes:



Camshaft timing is out of specifications
 
Valve timing is out of specifications
 

Trouble Code: P1391



CKP Or CMP Sensor Signal Intermittent

Possible Causes:



Camshaft Sensor is not installed properly
 
Engine valve timing is not within specifications
 
Perform a CKP and CMP Sensor relearn with the scan tool
 
Tone wheel or pulse ring is damaged
 

 
label.common.footer.alt.autozoneLogo