Chevrolet Citation/Omega/Phoenix/Skylark 1980-1985 Repair Guide

General Information


Click image to see an enlarged view

Fig. Fig. 1 Exploded view of the HEI integral coil distributor-1980 vehicles

Click image to see an enlarged view

Fig. Fig. 2 Fig. 6 View of the 1981-85 4-cylinder HEI EST distributor components. Note that there is no vacuum advance unit

Click image to see an enlarged view

Fig. Fig. 3 View of the 1981-85 6-cylinder HEI EST distributor components. Note that there is no vacuum advance unit

Click image to see an enlarged view

Fig. Fig. 4 View of the HEI distributor and coil-4-cylinder engine shown

The General Motors, HEI system for 1980 is a pulse-triggered, transistor-controlled, inductive discharge ignition system. It is a completely self-contained unit-all parts are contained within the distributor.

The distributor, in addition to housing the mechanical and vacuum advance mechanisms, contains the ignition coil, the electronic control module, and the magnetic triggering device. The magnetic pick-up assembly contains a permanent magnet, a pole piece with internal "teeth", and a pick-up coil (not to be confused with the ignition coil).

For 1981 and later vehicles, an HEI distributor with Electronic Spark Timing is used (for more information on EST, refer to ). The V6 engine uses a one piece distributor with the ignition coil mounted in the distributor cap, similar to 1980 vehicles. The L4 engine uses a smaller distributor with an externally mounted coil. The coil on the one piece distributor connects to the rotor through a resistance brush, while the external coil is connected by means of a high tension wire.

All spark timing changes in the 1981 and later distributors are done electronically by the Electronic Control Module (ECM) which monitors information from various engine sensors, computes the desired spark timing and then signals the distributor to change the timing accordingly. No vacuum or mechanical advance systems are used whatsoever.

In the HEI system, as in other electronic ignition systems, the breaker points have been replaced with an electronic switch-a transistor-which is located within the control module. This switching transistor performs the same function the points did in a conventional ignition system; it simply turns coil primary current on and off at the correct time. Essentially then, electronic and conventional ignition systems operate on the same principle.

The module which houses the switching transistor is controlled (turned on and off) by a magnetically generated impulse induced in the pick-up coil. When the teeth of the rotating timer align with the teeth of the pole piece, the induced voltage in the pick-up coil signals the electronic module to open the coil primary circuit. The primary current then decreases, and a high voltage is induced in the ignition coil secondary windings which is then directed through the rotor and high voltage leads (spark plug wires) to fire the spark plugs.

In essence then, the pick-up coil module system simply replaces the conventional breaker points and condenser. The condenser found within the distributor is for radio suppression purposes only and has nothing to do with the ignition process. The module automatically controls the dwell period, increasing it with increasing engine speed. Since dwell is automatically controlled, it cannot be adjusted. The module itself is non-adjustable and non-repairable and must be replaced if found defective.

Except for periodic checks of the spark plug wires, and an occasional check of the distributor cap for cracks (see Steps 1 and 2 under "Engine Runs, But Runs Rough or Cuts Out" for details), no maintenance is required on the HEI System. No periodic lubrication is necessary; engine oil lubricates the lower bushing, and an oil-filled reservoir lubricates the upper bushing.


Before going on to troubleshooting, it might be a good idea to take note of the following precautions:

Timing Light Use

Inductive pick-up timing lights are the best kind to use with HEI. Timing lights which connect between the spark plug and the spark plug wire occasionally (not always) give false readings.

Spark Plug Wires

The plug wires used with HEI systems are of a different construction than conventional wires. When replacing them, make sure you get the correct wires, since conventional wires won't carry the voltage. Also, handle them carefully to avoid cracking or splitting them and never pierce them.

Tachometer Use

Not all tachometers will operate or indicate correctly when used on a HEI system. While some tachometers may give a reading, this does not necessarily mean the reading is correct. In addition, some tachometers hook up differently from others. If you can't figure out whether or not your tachometer will work on your car, check with the tachometer manufacturer. Dwell readings, of course, have no significance at all.

HEI System Testers

Instruments designed specifically for testing HEI systems are available from several tool manufacturers. Some of these will even test the module itself. However, the tests given in the following information will require only an ohmmeter and a voltmeter.