Chevrolet Citation/Omega/Phoenix/Skylark 1980-1985 Repair Guide

Understanding Basic Electricity


Understanding the basic theory of electricity makes electrical troubleshooting much easier. Several gauges are used in electrical troubleshooting to see inside the circuit being tested. Without a basic understanding, it will be difficult to understand testing procedures.


Electricity is the flow of electrons-hypothetical particles thought to constitute the basic stuff of electricity. Many people have been taught electrical theory using an analogy with water. In a comparison with water flowing in a pipe, the electrons would be the water. As the flow of water can be measured, the flow of electricity can be measured. The unit of measurement is amperes, frequently abbreviated amps. An ammeter will measure the actual amount of current flowing in the circuit.

Just as the water pressure is measured in units such as pounds per square inch, electrical pressure is measured in volts. When a voltmeter's two probes are placed on two live portions of an electrical circuit with different electrical pressures, current will flow through the voltmeter and produce a reading which indicates the difference in electrical pressure between the two parts of the circuit.

While increasing the voltage in a circuit will increase the flow of current, the actual flow depends not only on voltage, but on the resistance of the circuit. The standard unit for measuring circuit resistance is an ohm, measured by an ohmmeter. The ohmmeter is somewhat similar to an ammeter, but incorporates its own source of power so that a standard voltage is always present.


An actual electric circuit consists of four basic parts. These are: the power source, such as a generator or battery; a hot wire, which conducts the electricity under a relatively high voltage to the component supplied by the circuit; the load, such as a lamp, motor, resistor or relay coil; and the ground wire, which carries the current back to the source under very low voltage. In such a circuit the bulk of the resistance exists between the point where the hot wire is connected to the load, and the point where the load is grounded. In an automobile, the vehicle's frame or body, which is made of steel, is used as a part of the ground circuit for many of the electrical devices.

Remember that, in electrical testing, the voltmeter is connected in parallel with the circuit being tested (without disconnecting any wires) and measures the difference in voltage between the locations of the two probes; that the ammeter is connected in series with the load (the circuit is separated at one point and the ammeter inserted so it becomes a part of the circuit); and the ohmmeter is self-powered, so that all the power in the circuit should be off and the portion of the circuit to be measured contacted at either end by one of the probes of the meter.

For any electrical system to operate, it must make a complete circuit. This simply means that the power flow from the battery must make a complete circle. When an electrical component is operating, power flows from the battery to the component, passes through the component causing it to perform it to function (such as lighting a light bulb) and then returns to the battery through the ground of the circuit. This ground is usually (but not always) the metal part of the vehicle on which the electrical component is mounted.

Perhaps the easiest way to visualize this is to think of connecting a light bulb with two wires attached to it to your vehicle's battery. The battery in your vehicle has two posts (negative and positive). If one of the two wires attached to the light bulb was attached to the negative post of the battery and the other wire was attached to the positive post of the battery, you would have a complete circuit. Current from the battery would flow out one post, through the wire attached to it and then to the light bulb, where it would pass through causing it to light. It would then leave the light bulb, travel through the other wire, and return to the other post of the battery.


The normal automotive circuit differs from this simple example in two ways. First, instead of having a return wire from the bulb to the battery, the light bulb return the current to the battery through the chassis of the vehicle. Since the negative battery cable is attached to the chassis and the chassis is made of electrically conductive metal, the chassis of the vehicle can serve as a ground wire to complete the circuit. Secondly, most automotive circuits contain switches to turn components on and off.

Some electrical components which require a large amount of current to operate also have a relay in their circuit. Since these circuits carry a large amount of current, the thickness of the wire in the circuit (gauge size) is also greater. If this large wire were connected from the component to the control switch on the instrument panel, and then back to the component, a voltage drop would occur in the circuit. To prevent this potential drop in voltage, an electromagnetic switch (relay) is used. The large wires in the circuit are connected from the vehicle battery to one side of the relay, and from the opposite side of the relay to the component. The relay is normally open, preventing current from passing through the circuit. An additional, smaller wire is connected from the relay to the control switch for the circuit. When the control switch is turned on, it grounds the smaller wire from the relay and completes the circuit.


If you were to disconnect the light bulb (from the previous example of a light-bulb being connected to the battery by two wires) from the wires and touch the two wires together (please take our word for this; don't try it), the result will be a shower of sparks. A similar thing happens (on a smaller scale) when the power supply wire to a component or the electrical component itself becomes grounded before the normal ground connection for the circuit. To prevent damage to the system, the fuse for the circuit blows to interrupt the circuit-protecting the components from damage. Because grounding a wire from a power source makes a complete circuit-less the required component to use the power-the phenomenon is called a short circuit. The most common causes of short circuits are: the rubber insulation on a wire breaking or rubbing through to expose the current carrying core of the wire to a metal part of the car, or a shorted switch.

Some electrical systems on the vehicle are protected by a circuit breaker which is, basically, a self-repairing fuse. When either of the described events takes place in a system which is protected by a circuit breaker, the circuit breaker opens the circuit the same way a fuse does. However, when either the short is removed from the circuit or the surge subsides, the circuit breaker resets itself and does not have to be replaced as a fuse does.