Log In
Search suggestions

    My Vehicles

    1984 Chrysler Daytona (Can) 2.2L FI Turbo (Can) 4cyl

    Find a Store

    Select Store

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998

    Proportioning Valves

    Print

    REMOVAL & INSTALLATION



    Cirrus, Stratus, Sebring Convertible and Breeze
    Bendix ABX-4 System

    See Figures 1 and 2

    You do not have to remove the HCU when replacing the proportioning valves.

    1. Disconnect the negative battery cable.
    2.  
    3. Disconnect the brake line fitting from the faulty proportioning valve in the HCU.
    4.  
    5. Unscrew and remove the proportioning valve requiring replaced from the HCU.
    6.  



    Click image to see an enlarged view

    Fig. Fig. 1: Proportioning valve identification



    Click image to see an enlarged view

    Fig. Fig. 2: Proportioning valve location on the HCU

    To install:
    1. Lubricate the O-ring seal on the new proportioning valve with clean brake fluid, from a fresh sealed container.
    2.  
    3. Install the proportioning valve in the HCU and hand-tighten it until it is fully installed and the O-ring seal is seated in the HCU. Then, tighten the valve to 30 ft. lbs. (40 Nm).
    4.  
    5. Connect the brake line to the proportioning valve and tighten the line nut to 12.5 ft. lbs. (17 Nm).
    6.  
    7. Bleed the base brake system in the usual fashion.
    8.  

    Teves Mark 20 System

    See Figures 3 and 4

    Never attempt to disassemble a proportioning valve.

    1. Raise and safely support the vehicle.
    2.  
    3. Remove the chassis brake tube nuts from the proportioning valve controlling the rear wheel of the vehicle which has premature wheel skid.
    4.  
    5. Remove the proportioning valve from the brake flex hose.
    6.  



    Click image to see an enlarged view

    Fig. Fig. 3: Proportioning valve location-Cirrus, Stratus and Breeze



    Click image to see an enlarged view

    Fig. Fig. 4: Proportioning valve location-Sebring convertible

    To install:
    1. Install the proportioning valve on the brake flex hose.
    2.  
    3. Tighten the 2 chassis brake tube nuts to 12.5 ft. lbs. (17 Nm).
    4.  
    5. Bleed the affected brake line, as outlined in this section.
    6.  

    Sebring Coupe and Avenger

    See Figure 5

    1. Disconnect the negative battery cable.
    2.  
    3. Remove the engine intake manifold assembly.
    4.  
    5. First label, then, using a flare nut wrench, unfasten the brake lines from the proportioning valve.
    6.  
    7. Loosen the mounting bolt and remove the proportioning valve from the vehicle.
    8.  



    Click image to see an enlarged view

    Fig. Fig. 5: ABS proportioning valve removal

    To install:
    1. Install the proportioning valve into the vehicle and tighten the mounting bolt.
    2.  
    3. Thread each brake line into its correct opening on the proportioning valve. Tighten each brake line fitting to 11 ft. lbs. (15 Nm).
    4.  
    5. Install the engine intake manifold assembly.
    6.  
    7. Connect the negative battery cable.
    8.  
    9. Bleed the brake system, as outlined later in this section.
    10.  

     
    AutoZone Logo