Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998

Speakers

Print

REMOVAL & INSTALLATION



Instrument Panel Speakers
Cirrus, Stratus, Sebring Convertible And Breeze

See Figures 1 and 2

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the instrument panel top cover as follows:
    1. Remove the screw from the right side of the top cover.
    2.  
    3. Carefully pry up on each end of the top cover to disengage the retaining clips.
    4.  

  4.  



Click image to see an enlarged view

Fig. Fig. 1: Instrument panel top cover removal

    1. Lift up the rear edge of the top cover, using a trim stick along the rear edge.
    2.  
    3. While lifting up on the rear edge, slide the top cover rearward to disengage the front clips and remove the top cover.
    4.  




Click image to see an enlarged view

Fig. Fig. 2: Instrument panel speaker removal

  1. Unfasten the speaker retaining screws.
  2.  
  3. Partially lift the speaker up, detach the electrical connector, then remove the speaker from the vehicle.
  4.  

To install:
  1. Attach the electrical connector to the speaker, then position the speaker in the instrument panel.
  2.  
  3. Install the speaker retaining screws.
  4.  
  5. Install the instrument panel top cover.
  6.  
  7. Connect the negative battery cable.
  8.  

Sebring Coupe And Avenger

See Figure 3

  1. Disconnect the negative battery cable.
  2.  
  3. Using a small, flat bladed prying tool, carefully pry upward on the left or right side speaker.
  4.  
  5. Partially lift the speaker up, detach the electrical connector, then remove the speaker from the vehicle.
  6.  



Click image to see an enlarged view

Fig. Fig. 3: Instrument panel speaker removal

To install:
  1. Attach the electrical connector to the speaker, then position the speaker in the instrument panel.
  2.  
  3. Apply slight downward pressure on the speaker to engage the retaining clips.
  4.  
  5. Connect the negative battery cable.
  6.  

Front Door Speakers

Cirrus, Stratus, Sebring Convertible And Breeze

See Figures 4, 5 and 6

  1. Disconnect the negative battery cable.
  2.  
  3. Using a small, prying tool, remove the door panel speaker grille.
  4.  
  5. Remove the 3 speaker mounting screws.
  6.  
  7. Partially pull the speaker up out of its mounting position, then unplug the connector and remove the speaker from the vehicle.
  8.  



Click image to see an enlarged view

Fig. Fig. 4: Remove the 3 front speaker mounting screws



Click image to see an enlarged view

Fig. Fig. 5: Pull the speaker unit out from the side door panel ...



Click image to see an enlarged view

Fig. Fig. 6: ... then disengage the speaker wiring connector

To install:
  1. Attach the electrical connector, then position the speaker in the door.
  2.  
  3. Install and tighten the 3 speaker retaining screws.
  4.  
  5. Install the door panel speaker grille.
  6.  
  7. Connect the negative battery cable.
  8.  

Sebring Coupe And Avenger

See Figure 7

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the door trim panel, as outlined in General Information & Maintenance 0 of this repair guide.
  4.  
  5. Remove the speaker retaining screws.
  6.  
  7. Partially lift the speaker out, detach the electrical connector, then remove the speaker from the door.
  8.  



Click image to see an enlarged view

Fig. Fig. 7: Door speaker assembly removal

To install:
  1. Attach the electrical connector, then position the speaker in the door.
  2.  
  3. Install and tighten the speaker retaining screws.
  4.  
  5. Install the door trim panel, as outlined in General Information & Maintenance 0 of this repair guide.
  6.  
  7. Connect the negative battery cable.
  8.  

Rear Speakers

Cirrus, Stratus And Breeze

See Figure 8

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the parcel shelf trim panel from the vehicle using the following procedure:
    1. Remove the interior upper quarter trim panels.
    2.  
    3. Remove the rear seat cushion and seat back, or quarter extension panels.
    4.  
    5. Remove the push-in fastener securing the parcel shelf trim to the shelf panel.
    6.  
    7. Pull the trim forward to disengage the clip holding the trim to the shelf panel.
    8.  
    9. Remove the parcel shelf trim panel from the vehicle.
    10.  

  4.  
  5. Remove the 4 speaker retaining screws.
  6.  
  7. Partially pull the speaker up and out of its mounting position, then unplug the connector and remove the speaker from the vehicle.
  8.  



Click image to see an enlarged view

Fig. Fig. 8: Rear speaker removal

To install:
  1. Attach the electrical connector, then position the speaker in the rear shelf panel.
  2.  

Be sure that the wiring connectors are facing outward in the vehicle.

  1. Install and tighten the 4 speaker retaining screws.
  2.  
  3. Install the parcel shelf panel into the vehicle.
  4.  
  5. Connect the negative battery cable.
  6.  

Sebring Coupe And Avenger

See Figure 9

  1. Disconnect the negative battery cable.
  2.  
  3. From inside the trunk area, remove the speaker grille retaining fasteners. Remove the speaker grille from the vehicle. If accessible from the trunk area, unplug the speaker connector.
  4.  
  5. Remove the speaker retaining screws.
  6.  



Click image to see an enlarged view

Fig. Fig. 9: Rear speaker assembly

  1. Partially pull the speaker up and out of its mounting position, then unplug the wiring connector, if not done earlier, and remove the speaker from the vehicle.
  2.  
  3. Installation is the reverse of the removal procedure.
  4.  
  5. Connect the negative battery cable.
  6.  

Rear Quarter Panel Speaker

Sebring Convertible

See Figure 10

  1. Disconnect the negative battery cable.
  2.  
  3. Using a small, prying tool, remove the rear quarter panel speaker grille.
  4.  
  5. Remove the 4 speaker retaining screws.
  6.  



Click image to see an enlarged view

Fig. Fig. 10: Rear quarter panel speaker removal

  1. Partially pull the speaker up and out of its mounting position, then unplug the connector and remove the speaker from the vehicle.
  2.  
  3. Installation is the reverse of the removal procedure.
  4.  
  5. Connect the negative battery cable.
  6.  

 
label.common.footer.alt.autozoneLogo