Chrysler Concorde/Intrepid/LHS/New Yorker/Vision 1993-1997

Seats

Print

REMOVAL & INSTALLATION



Front Seats

See Figure 1



Click image to see an enlarged view

Fig. Fig. 1: Front seat mounting

  1. Position the seat full forward.
  2.  
  3. Unplug the front seat wire harness connector from the body harness connector.
  4.  
  5. Remove the bolts holding the front of the seat track to the floor.
  6.  
  7. Remove the bolts holding the rear of the seat track to the floor.
  8.  
  9. Remove the seat from the vehicle.
  10.  

To install:
  1. Install the seat into the vehicle.
  2.  
  3. Install the bolts holding the rear of the seat track to the floor and tighten securely.
  4.  
  5. Install the bolts holding the front of the seat track to the floor and tighten securely.
  6.  
  7. Plug the front seat wire harness connector to the body harness connector.
  8.  

Rear Seats
STANDARD SEAT

See Figures 2 and 3



Click image to see an enlarged view

Fig. Fig. 2: Rear seat cushion installation



Click image to see an enlarged view

Fig. Fig. 3: Rear seat back installation

  1. To remove the rear seat cushion, perform the following:
    1. Pull upward on each end of the rear seat cushion to disengage the retainer loops from the cups in the floor.
    2.  
    3. Remove the cushion from the vehicle.
    4.  

  2.  
  3. Remove the seat back by performing the following:
    1. Remove the seat cushion.
    2.  
    3. Remove the nuts holding the rear seat back and belts to the floor.
    4.  
    5. Push the rear seat back upward to disengage the hooks at the top of the seat back.
    6.  

  4.  

To install:
  1. Install the seat back as follows:
    1. Position the seat back in the vehicle, then engage the hooks at the top of the seat back.
    2.  
    3. Install the nuts holding the rear seat back and belts to the floor and tighten securely.
    4.  

  2.  
  3. To install the rear seat cushion, perform the following:
    1. Install the cushion into the vehicle.
    2.  
    3. Engage the retainer loops into the cup on the floor.
    4.  
    5. Push downward on each end of the rear seat cushion to engage the retainers.
    6.  

  4.  

REAR SEAT BACK WITH CHILD SEAT

See Figure 4

Click image to see an enlarged view

Fig. Fig. 4: Rear seat back with child seat installation

  1. Remove the rear seat cushion.
  2.  
  3. Open the child seat and remove the lining.
  4.  
  5. Remove the bolts holding the seat back frame to the trunk closure panel through the holes in the child seat module.
  6.  
  7. Remove the nuts holding the bottom of the rear seat back to the floor.
  8.  
  9. Lift the seat back upward to disengage the retainer hook from the trunk closure panel.
  10.  
  11. Remove the rear seat back from the vehicle.
  12.  

To install:
  1. Position the seat back in the vehicle.
  2.  
  3. Engage the retainer loops on the seat back into the trunk closure panel.
  4.  
  5. Install the nuts holding the bottom of the rear seat back to the floor.
  6.  
  7. Install the bolts holding the seat back frame to the trunk closure panel through the holes in the child seat module.
  8.  
  9. Install the child seat lining.
  10.  
  11. Install the rear seat cushion.
  12.  

CHILD SEAT MODULE

See Figure 5

Click image to see an enlarged view

Fig. Fig. 5: Child seat module installation

  1. Remove the rear seat back from the vehicle.
  2.  
  3. Separate the lower bolster from the child seat.
  4.  
  5. Remove the inner liner from the child seat module.
  6.  
  7. Disengage the push-in fasteners holding the upper bolster to the child seat module above the shoulder belts.
  8.  
  9. Remove the screws holding the bottom of the child seat module to the seat back frame.
  10.  
  11. Separate the child seat module from the seat back frame.
  12.  

To install:
  1. Position the child seat module to the seat back frame.
  2.  
  3. Install the screws holding the bottom of the child seat module to the seat back frame.
  4.  

Be careful not to get the seat belt webbing caught between the module and the seat back frame when installing the upper screws.

  1. Install the screws holding the top of the child seat module to the seat back frame behind the shoulder belts.
  2.  
  3. Engage the push-in fasteners holding the upper bolster to the child seat module above the shoulder belts.
  4.  
  5. Install the inner liner to the child seat module.
  6.  
  7. Position the lower bolster to the child seat.
  8.  
  9. Slide the lower bolster cushion retainer into the channel on the child seat cushion.
  10.  
  11. Install the rear seat back to the vehicle.
  12.  

 
label.common.footer.alt.autozoneLogo