Chrysler Front Wheel Drive Cars 4-CYL 1981-1995 Repair Information

Air Conditioning System


Be sure to consult the laws in your area before servicing the air conditioning system. In most areas, it is illegal to perform repairs involving refrigerant unless the work is done by a certified technician. Also, it is quite likely that you will not be able to purchase refrigerant without proof of certification.


There are two major hazards associated with air conditioning systems and they both relate to the refrigerant gas. First, the refrigerant gas (R-12 or R-134a) is an extremely cold substance. When exposed to air, it will instantly freeze any surface it comes in contact with, including your eyes. The other hazard relates to fire (if your vehicle is equipped with R-12. Although normally non-toxic, the R-12 gas becomes highly poisonous in the presence of an open flame. One good whiff of the vapor formed by burning R-12 can be fatal. Keep all forms of fire (including cigarettes) well clear of the air conditioning system.

Because of the inherent dangers involved with working on air conditioning systems, these safety precautions must be strictly followed.

Avoid contact with a charged refrigeration system, even when working on another part of the air conditioning system or vehicle. If a heavy tool comes into contact with a section of tubing or a heat exchanger, it can easily cause the relatively soft material to rupture.
When it is necessary to apply force to a fitting which contains refrigerant, as when checking that all system couplings are securely tightened, use a wrench on both parts of the fitting involved, if possible. This will avoid putting torque on refrigerant tubing. (It is also advisable to use tube or line wrenches when tightening these flare nut fittings.)

R-12 refrigerant is a chlorofluorocarbon which, when released into the atmosphere, can contribute to the depletion of the ozone layer in the upper atmosphere. Ozone filters out harmful radiation from the sun.

Do not attempt to discharge the system without the proper tools. Precise control is possible only when using the service gauges and a proper A/C refrigerant recovery station. Wear protective gloves when connecting or disconnecting service gauge hoses.
Discharge the system only in a well ventilated area, as high concentrations of the gas which might accidentally escape can exclude oxygen and act as an anesthetic. When leak testing or soldering, this is particularly important, as toxic gas is formed when R-12 contacts any flame.
Never start a system without first verifying that both service valves are properly installed, and that all fittings throughout the system are snugly connected.
Avoid applying heat to any refrigerant line or storage vessel. Charging may be aided by using water heated to less than 125°F (50°C) to warm the refrigerant container. Never allow a refrigerant storage container to sit out in the sun, or near any other source of heat, such as a radiator or heater.
Always wear goggles to protect your eyes when working on a system. If refrigerant contacts the eyes, it is advisable in all cases to consult a physician immediately.
Frostbite from liquid refrigerant should be treated by first gradually warming the area with cool water, and then gently applying petroleum jelly. A physician should be consulted.
Always keep refrigerant drum fittings capped when not in use. If the container is equipped with a safety cap to protect the valve, make sure the cap is in place when the can is not being used. Avoid sudden shock to the drum, which might occur from dropping it, or from banging a heavy tool against it. Never carry a drum in the passenger compartment of a vehicle.
Always completely discharge the system into a suitable recovery unit before painting the vehicle (if the paint is to be baked on), or before welding anywhere near refrigerant lines.
When servicing the system, minimize the time that any refrigerant line or fitting is open to the air in order to prevent moisture or dirt from entering the system. Contaminants such as moisture or dirt can damage internal system components. Always replace O-rings on lines or fittings which are disconnected. Prior to installation coat, but do not soak, replacement O-rings with suitable compressor oil.


It is recommended, and possibly required by law, that a qualified technician perform the following services.

Some of the vehicles covered by this information may be equipped with R-134a refrigerant systems, rather than R-12. Be ABSOLUTELY SURE what type of system you are working on before attempting to add refrigerant. Use of the wrong refrigerant or oil will cause damage to the system.

The most important aspect of air conditioning service is the maintenance of a pure and adequate charge of refrigerant in the system. A refrigeration system cannot function properly if a significant percentage of the charge is lost. Leaks are common because the severe vibration encountered underhood in an automobile can easily cause a sufficient cracking or loosening of the air conditioning fittings; allowing, the extreme operating pressures of the system to force refrigerant out.

The problem can be understood by considering what happens to the system as it is operated with a continuous leak. Because the expansion valve regulates the flow of refrigerant to the evaporator, the level of refrigerant there is fairly constant. The receiver/drier stores any excess refrigerant, and so a loss will first appear there as a reduction in the level of liquid. As this level nears the bottom of the vessel, some refrigerant vapor bubbles will begin to appear in the stream of liquid supplied to the expansion valve. This vapor decreases the capacity of the expansion valve very little as the valve opens to compensate for its presence. As the quantity of liquid in the condenser decreases, the operating pressure will drop there and throughout the high side of the system. As the refrigerant continues to be expelled, the pressure available to force the liquid through the expansion valve will continue to decrease, and, eventually, the valve's orifice will prove to be too much of a restriction for adequate flow even with the needle fully withdrawn.

At this point, low side pressure will start to drop, and a severe reduction in cooling capacity, marked by freeze-up of the evaporator coil, will result. Eventually, the operating pressure of the evaporator will be lower than the pressure of the atmosphere surrounding it, and air will be drawn into the system wherever there are leaks in the low side.

Because all atmospheric air contains at least some moisture, water will enter the system mixing with the refrigerant and oil. Trace amounts of moisture will cause sludging of the oil, and corrosion of the system. Saturation and clogging of the filter/drier, and freezing of the expansion valve orifice will eventually result. As air fills the system to a greater and greater extent, it will interfere more and more with the normal flows of refrigerant and heat.

From this description, it should be obvious that much of the repairman's focus in on detecting leaks, repairing them, and then restoring the purity and quantity of the refrigerant charge. A list of general rules should be followed in addition to all safety precautions:

Keep all tools as clean and dry as possible.
Thoroughly purge the service gauges/hoses of air and moisture before connecting them to the system. Keep them capped when not in use.
Thoroughly clean any refrigerant fitting before disconnecting it, in order to minimize the entrance of dirt into the system.
Plan any operation that requires opening the system beforehand, in order to minimize the length of time it will be exposed to open air. Cap or seal the open ends to minimize the entrance of foreign material.
When adding oil, pour it through an extremely clean and dry tube or funnel. Keep the oil capped whenever possible. Do not use oil that has not been kept tightly sealed.
Purchase refrigerant intended for use only in automatic air conditioning systems.
Completely evacuate any system that has been opened for service, or that has leaked sufficiently to draw in moisture and air. This requires evacuating air and moisture with a good vacuum pump for at least one hour. If a system has been open for a considerable length of time it may be advisable to evacuate the system for up to 12 hours (overnight).
Use a wrench on both halves of a fitting that is to be disconnected, so as to avoid placing torque on any of the refrigerant lines.
When overhauling a compressor, pour some of the oil into a clean glass and inspect it. If there is evidence of dirt, metal particles, or both, flush all refrigerant components with clean refrigerant before evacuating and recharging the system. In addition, if metal particles are present, the compressor should be replaced.
Schrader valves may leak only when under full operating pressure. Therefore, if leakage is suspected but cannot be located, operate the system with a full charge of refrigerant and look for leaks from all Schrader valves. Replace any faulty valves.

Additional Preventive Maintenance

The easiest and most important preventive maintenance for your A/C system is to be sure that it is used on a regular basis. Running the system for five minutes each month (no matter what the season) will help assure that the seals and all internal components remain lubricated.


See Figure 1

Click image to see an enlarged view

Fig. Fig. 1: An antifreeze tester can be use to determine the freezing and boiling level of your coolant

In order to prevent heater core freeze-up during A/C operation, it is necessary to maintain a proper antifreeze protection. Use a hand-held antifreeze tester (hydrometer) to periodically check the condition of the antifreeze in your engine's cooling system.

Antifreeze should not be used longer than the manufacturer specifies.


For efficient operation of an air conditioned vehicle's cooling system, the radiator cap should have a holding pressure which meets manufacturer's specifications. A cap which fails to hold these pressures should be replaced.


Any obstruction of or damage to the condenser configuration will restrict the air flow which is essential to its efficient operation. It is therefore a good rule to keep this unit clean and in proper physical shape.

Bug screens which are mounted in front of the condenser (unless they are original equipment) are regarded as obstructions.


This single molded drain tube expels the condensation, which accumulates on the bottom of the evaporator housing, into the engine compartment. If this tube is obstructed, the air conditioning performance can be restricted and condensation buildup can spill over onto the vehicle's floor.


R-12 refrigerant is a chlorofluorocarbon which, when released into the atmosphere, can contribute to the depletion of the ozone layer in the upper atmosphere. Ozone filters out harmful radiation from the sun.

The easiest and often most important check for the air conditioning system consists of a visual inspection of the system components. Visually inspect the air conditioning system for refrigerant leaks, damaged compressor clutch, compressor drive belt tension and condition, plugged evaporator drain tube, blocked condenser fins, disconnected or broken wires, blown fuses, corroded connections and poor insulation.

A refrigerant leak will usually appear as an oily residue at the leakage point in the system. The oily residue soon picks up dust or dirt particles from the surrounding air and appears greasy. Through time, this will build up and appear to be a heavy dirt impregnated grease. Most leaks are caused by damaged or missing O-ring seals at the component connections, damaged charging valve cores or missing service gauge port caps.

For a thorough visual and operational inspection, check the following:

  1. Check the surface of the radiator and condenser for dirt, leaves or other material which might block air flow.
  3. Check for kinks in hoses and lines. Check the system for leaks.
  5. Make sure the drive belt is under the proper tension. When the air conditioning is operating, make sure the drive belt is free of noise or slippage.
  7. Make sure the blower motor operates at all appropriate positions, then check for distribution of the air from all outlets with the blower on HIGH .

Keep in mind that under conditions of high humidity, air discharged from the A/C vents may not feel as cold as expected, even if the system is working properly. This is because the vaporized moisture in humid air retains heat more effectively than does dry air, making the humid air more difficult to cool.

  1. Make sure the air passage selection lever is operating correctly. Start the engine and warm it to normal operating temperature, then make sure the hot/cold selection lever is operating correctly.


Discharging, evacuating and charging the air conditioning system must be performed by a properly trained and certified mechanic in a facility equipped with refrigerant recovery/recycling equipment that meets SAE standards for the type of system to be serviced.

If you don't have access to the necessary equipment, we recommend that you take your vehicle to a reputable service station to have the work done. If you still wish to perform repairs on the vehicle, have them discharge the system, then take your vehicle home and perform the necessary work. When you are finished, return the vehicle to the station for evacuation and charging. Just be sure to cap ALL A/C system fittings immediately after opening them and keep them protected until the system is recharged.