Chrysler Front Wheel Drive Cars 6-CYL 1988-1995 Repair Information

Seats

Print

REMOVAL & INSTALLATION



Front Seats

See Figures 1 and 2

  1. Position the seat full forward.
  2.  
  3. Remove the screws holding the rear track riser covers and separate the covers from the tracks.
  4.  
  5. On power seats, remove the outboard track cover.
  6.  
  7. Remove the inboard seat belt attaching bolt from the floor.
  8.  
  9. Remove the nuts holding the seat track to the floor.
  10.  
  11. Position the seat full rearward.
  12.  
  13. On power seats, remove the door sill scuff plate and unplug the wire connector.
  14.  
  15. Remove the bolts holding the seat track to the crossmember.
  16.  
  17. Remove the seat from the vehicle.
  18.  



Click image to see an enlarged view

Fig. Fig. 1: Manual front seat mounting fastener locations



Click image to see an enlarged view

Fig. Fig. 2: Power front seat mounting fastener locations

To install:
  1. Install the seat into the vehicle.
  2.  
  3. Install the bolts to hold the seat track to the crossmember.
  4.  
  5. On power seats, install the door sill scuff plate and attach the wire connector.
  6.  
  7. Position the seat full forward.
  8.  
  9. Install the nuts to hold the seat track to the floor.
  10.  
  11. Install the inboard seat belt attaching bolt to the floor.
  12.  
  13. On power seats, install the outboard track cover.
  14.  
  15. Install the covers onto the tracks, then install the screws to hold the rear track riser covers.
  16.  

Rear Seats

LEBARON, ACCLAIM, SPIRIT, SUNDANCE, SHADOW AND TC BY MASERATI

See Figure 3

  1. To remove the rear seat cushion, perform the following:
    1. Remove the bolts holding the cushion to the floor.
    2.  
    3. Push the center occupant seat belts through the openings in the cushion.
    4.  
    5. Remove the cushion from the vehicle.
    6.  

  2.  
  3. Remove the seat back by performing the following:
    1. Hinge the seat back forward and disengage the push-in fasteners holding the carpet backing to the trunk floor.
    2.  
    3. Remove the bolts holding the outboard hinge pivot bracket to the seat back.
    4.  
    5. Pull the seat back outward to disengage the inboard pivot and remove it from the vehicle.
    6.  

  4.  



Click image to see an enlarged view

Fig. Fig. 3: Exploded view of the rear seat cushion and back mounting

To install:
  1. Install the seat back as follows:
    1. Position the seat back in the vehicle, then push the seat back inward to engage the inboard pivot.
    2.  
    3. Install the bolts to hold the outboard hinge pivot bracket to the seat back.
    4.  
    5. Engage the push-in fasteners to hold the carpet backing to the trunk floor. Swing the seat back rearward.
    6.  

  2.  
  3. To install the rear seat cushion, perform the following:
    1. Install the cushion into the vehicle.
    2.  
    3. Route the center occupant seat belts through the openings in the cushion.
    4.  
    5. Install the bolts to hold the cushion to the floor.
    6.  

  4.  

NEW YORKER, DYNASTY, IMPERIAL, FIFTH AVE., PREMIER AND MONACO
  1. To remove the rear seat cushion, perform the following:
    1. Remove the bolts holding the cushion to the floor.
    2.  
    3. Push the center occupant seat belts through the openings in the cushion.
    4.  
    5. Remove the cushion from the vehicle.
    6.  

  2.  
  3. Remove the seat back by performing the following:
    1. Remove the bolts holding the seat back to the rear floor kick-up.
    2.  
    3. Lift the seat back upward to disengage the upper hooks from the shelf support panel.
    4.  
    5. Separate the seat back from the vehicle.
    6.  

  4.  

To install:
  1. Install the seat back as follows:
    1. Position the seat back in the vehicle.
    2.  
    3. Slide the seat back down to engage the upper hooks to the shelf support panel.
    4.  
    5. Install the bolts to hold the seat back to the rear floor kick-up.
    6.  

  2.  
  3. To install the rear seat cushion, perform the following:
    1. Install the cushion into the vehicle.
    2.  
    3. Route the center occupant seat belts through the openings in the cushion.
    4.  
    5. Install the bolts to hold the cushion to the floor.
    6.  

  4.  

DAYTONA
  1. Hinge the seat backs forward.
  2.  
  3. Remove the bolts holding the rear seat frame to the floor on the sides of the center floor hump near the luggage compartment kick-up.
  4.  
  5. Pull the seat forward to disengage the retaining hooks from the floor.
  6.  
  7. Remove the seat from the vehicle.
  8.  

To install:
  1. Install the seat into the vehicle.
  2.  
  3. Push the seat rearward to engage the retaining hooks to the floor.
  4.  
  5. Install the bolts to hold the rear seat frame to the floor on the sides of the center floor hump near the luggage compartment kick-up.
  6.  
  7. Hinge the seat backs rearward.
  8.  

 
label.common.footer.alt.autozoneLogo