Chrysler Full-Size Trucks 1997-2000 Repair Guide

Injectors

Print

GENERAL INFORMATION



The fuel injectors are mounted on the left side of the cylinder head on 1997-98 models, on the top, center of the head on 1999-00 models, and are connected to the fuel pump by the high pressure fuel lines.



Click image to see an enlarged view

Fig. The injector is a precise one-way valve that sprays a metered amount of fuel at high pressure into the combustion chamber

The injectors consist of the nozzle holder, O-ring, water seal, shims, spring, needle valve and nozzle. Fuel enters the injector through the top of the injector (fuel inlet) and is routed to the needle valve bore. The injector fires when fuel pressure rises to an amount sufficient to overcome the needle valve spring tension. The pressure needed to overcome the needle valve spring tension is about 4,000 psi (28,000 kPa). This pressure is commonly known as the "pop" pressure.

As the needle valve opens, fuel flows rapidly through the spray holes in the nozzle tip into the combustion chamber. After this injection, the fuel pressure drops and the needle valve is closed preventing further fuel flow, and conversely, exhaust flow into the injector.

REMOVAL & INSTALLATION



1997-98 Models
  1. Disconnect the negative battery cable(s). Remove the throttle linkage and bracket if necessary.
  2.  
  3. Disconnect the high-pressure fuel supply line to the injector.
  4.  
  5. Disconnect the fuel drain manifold.
  6.  



Click image to see an enlarged view

Fig. Fuel is supplied to the six diesel fuel injectors by individual high-pressure lines



Click image to see an enlarged view

Fig. Unscrew and remove the diesel fuel injector-1997-98 models shown

  1. Clean the area around the injector.
  2.  



Click image to see an enlarged view

Fig. Use a wire brush to clean the injector bore as shown


NOTE
Certain types of injectors MAY have an O-ring located above the hold-down nut.



Click image to see an enlarged view

Fig. Use only one copper washer on the diesel injector

  1. Using the correct deepwell socket, remove the injector from the cylinder head.
  2.  

To install:



Click image to see an enlarged view

Fig. Install the diesel injector so that its tab is aligned with the notch in the bore-1997-98 models

  1. Clean the injector bore with a bore brush.
  2.  
  3. Assemble the injector and one new copper, sealing washer. NEVER use more than one copper washer.
  4.  
  5. Apply a thin coat of anti-seize compound to the threads of the injector hold-down nut and between the top of the nut and the injector body.
  6.  
  7. Align the protrusion in the injector with the notch in the bore and install the injector. Tighten the injector retainer nut to 44 ft. lbs. (60 Nm).
  8.  
  9. Push the O-ring into the groove at the top of the injector, if applicable.
  10.  
  11. Using new sealing washers, assemble the fuel drain manifold and high-pressure lines. Tighten the banjo fitting bolt to 6 ft. lbs. (8 Nm). Leave the high-pressure line loose temporarily.
  12.  


CAUTION
Do NOT place any part of the hand near the base of the high pressure line. A fuel leak from a high-pressure fuel line has sufficient pressure to penetrate the skin and cause serious bodily harm. Do NOT bleed the lines if the engine is hot. Fuel spilling onto a hot exhaust manifold creates the danger of fire.

  1. To bleed air from the system, run or crank the engine and tighten the fitting after the air has expelled. If more than one injector was replaced, tighten each fitting after the air has expelled before going on to the next injector fitting. Tighten the fittings to 22 ft. lbs. (30 Nm). The operation is complete when the engine runs smoothly. If the air cannot be removed, check the pump and supply line for suction leaks.
  2.  
  3. Install the throttle linkage and bracket if they were removed.
  4.  

1999-00 Models
  1. Disconnect the negative battery cable(s). Remove the throttle linkage and bracket if necessary.
  2.  
  3. To access the injectors at cylinders #1 and #2, remove the intake manifold heater assembly. To access the injector at cylinder #5, remove the engine-lifting bracket.
  4.  
  5. Clean the area around the injector.
  6.  
  7. Disconnect the high-pressure fuel supply line to the injector.
  8.  
  9. Remove the valve cover.
  10.  
  11. Thread special tool 8324 onto the end of the injector tube and pull injector tube from cylinder head. Remove and discard the old O-ring.
  12.  
  13. Remove the fuel injector hold-down clamp bolt at front end of clamp. Do NOT loosen or remove special bolt at rear end of clamp. Remove injector by sliding it out.
  14.  
  15. Thread the rod from special tool 8318 into the top of the fuel injector. Remove injector from cylinder head.
  16.  

To install:

  1. Reverse the removal procedure.
  2.  
  3. Use a new copper sealing washer and a new O-ring. Copper washer thickness must be 0.060 in. (1.5mm).
  4.  
  5. Oil all parts before installation.
  6.  
  7. Position the inlet hole towards connector tube.
  8.  
  9. Tighten the opposite clamp bolt to 89 inch lbs. (10 Nm).
  10.  



Click image to see an enlarged view

Fig. Fuel injector connections-1999-2000

TESTING (ALL MODELS)




CAUTION
If examining for leaks, use a sheet of cardboard to show any spraying fuel. Do NOT use your hand and do wear safety goggles. The extremely high pressure can cause serious personal injury, especially to your skin and eyes.

A leaking fuel injector can cause fuel knock, poor performance, black smoke, poor fuel economy and rough engine idle. If the needle valve does NOT operate properly, the engine may misfire and produce low power.

A leak in the injection pump-to-injector high-pressure fuel line can cause many of the same symptoms as a malfunctioning injector. First check the lines before the injectors.



Click image to see an enlarged view

Fig. Loosen the fittings one-at-a-time to check the effect on engine rpm-no change in rpm indicates a faulty injector

  1. To check the injectors, start the engine and loosen the high-pressure line nut one-at-a-time at each injector. Listen for a decrease in engine speed.
  2.  



Click image to see an enlarged view

Fig. Use a tester like the one shown to measure pop pressure for the diesel fuel injector

  1. If the engine speed drops, the injector is operating normally. If the engine speed remains the same, the injector is malfunctioning. After testing each injector, tighten the line nuts to 22 ft. lbs. (30 Nm) on 1997-98 Models, 30 ft. lbs. (40 Nm) on later units.
  2.  
  3. If an injector is found to be malfunctioning, remove it and test it on a standard bench-mount injector tester. Follow the manufacturer's instructions for bench testing the injector.
  4.  
  5. If the opening (pop) pressure is below specifications, replace the injector. The pop pressure is 3,822 psi (26,252 kPa) for 1997-98 Models, 4,500 psi (31,026 kPa) for 1999-2000 Models.
  6.  

 
label.common.footer.alt.autozoneLogo