Cobalt 2006-2008, G5 2007

Arming The System

Print

Zone 1



  1. Remove the key from the ignition switch.
  2.  
  3. Connect the front end sensor connector to the front end sensor (2).
  4.  
  5. Connect the CPA to the front end sensor connector.
  6.  
  7. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  8.  
  9. Install the BCM fuse center cover.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

Zone 2



  1. Remove the key from the ignition switch.
  2.  
  3. To enable the SIS-right go to step 3. To enable the roof rail module-right go to step 7, and to enable the seat belt pretensioner-RF go to step 10.
  4.  
  5. Install the SIS-right connector to the SIS-right.
  6.  
  7. Install the CPA to the SIS connector.
  8.  
  9. Reinstall door water deflector.
  10.  
  11. Install the RH door trim panel.
  12.  
  13. Connect the roof rail module-right connector to the vehicle harness connector.
  14.  
  15. Install the CPA to the roof rail module-right connector.
  16.  
  17. Install the garnish molding to the upper lock pillar.
  18.  
  19. Connect the seat belt pretensioner-LF and install the CPA.
  20.  
  21. Install the lower center pillar.
  22.  
  23. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  24.  
  25. Install the BCM fuse center cover.
  26.  
  27. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  28.  

Zone 3



  1. Remove the key from the ignition switch.
  2.  
  3. Connect the steering wheel module coil connector to the vehicle harness connector.
  4.  
  5. Install the CPA to the steering wheel module coil connector.
  6.  
  7. Install the left outer trim cover to the I/P.
  8.  
  9. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  10.  
  11. Install the BCM fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 5



  1. Remove the key from the ignition switch.
  2.  
  3. Connect the I/P module connector to the vehicle harness connector.
  4.  
  5. Install the CPA to the I/P module connector.
  6.  
  7. Install the right outer trim cover to the I/P.
  8.  
  9. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  10.  
  11. Install the BCM fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 6



  1. Remove the key from the ignition switch.
  2.  
  3. To enable the SIS-left go to step 3. To enable the roof rail module-left go to step 7, and to enable the seat belt pretensioner-LF go to step 10.
  4.  
  5. Install the SIS-left connector to the SIS-left.
  6.  
  7. Install the CPA to the SIS connector.
  8.  
  9. Reinstall door water deflector.
  10.  
  11. Install the LH door trim panel.
  12.  
  13. Connect the roof rail module-left connector to the vehicle harness connector.
  14.  
  15. Install the CPA to the roof rail module-left connector.
  16.  
  17. Install the garnish molding to the upper lock pillar.
  18.  
  19. Connect the seat belt pretensioner-LF and install the CPA.
  20.  
  21. Install the lower center pillar.
  22.  
  23. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  24.  
  25. Install the BCM fuse center cover.
  26.  
  27. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash, then, turn OFF.
  28.  

Zone 8



  1. Remove the key from the ignition switch.
  2.  
  3. Connect the roof rail module-left connector to the vehicle harness connector.
  4.  
  5. Install the CPA to the roof rail module-left connector.
  6.  
  7. Install the garnish molding to the left upper lock pillar.
  8.  
  9. Connect the seat belt pretensioner-LF connector.
  10.  
  11. Install the CPA to the seat belt pretensioner-LF connector.
  12.  
  13. Install the left/driver lower center pillar trim.
  14.  
  15. Connect the steering wheel module coil connector to the vehicle harness connector.
  16.  
  17. Install the CPA to the steering wheel module coil connector.
  18.  
  19. Install the driver/left outer trim cover to the I/P.
  20.  
  21. Connect the I/P module connector to the vehicle harness connector.
  22.  
  23. Install the CPA to the I/P module connector.
  24.  
  25. Install the passenger/right outer trim cover to the I/P.
  26.  
  27. Connect the seat belt pretensioner-RF connector.
  28.  
  29. Install the CPA to the seat belt pretensioner-RF connector.
  30.  
  31. Install the right lower center pillar trim.
  32.  
  33. Connect the roof rail module-right connector to the vehicle harness connector.
  34.  
  35. Install the CPA to the roof rail module-right connector.
  36.  
  37. Install the garnish molding to the right upper lock pillar.
  38.  
  39. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  40.  
  41. Install the BCM fuse center cover.
  42.  
  43. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  44.  

 
label.common.footer.alt.autozoneLogo