Cobalt 2006-2008, G5 2007

2.0L L4 VIN X Std 3

Print

Trouble Code: P0607



Vehicle Speed Output Circuit Malfunction

Possible Causes:



VSS output signal circuit is open, shorted to ground or to power
 
VSS output signal problem related to the Instrument Cluster or the Electronic Suspension Control Module (internal problem)
 
ECM has failed
 

Trouble Code: P060D



Control Module Vehicle Options Incorrect

Possible Causes:



ECM is not properly programmed
 
ECM has failed
 

Trouble Code: P0610



Generator Signal Range/Performance

Possible Causes:



Generator 'L' terminal circuit is open, shorted to ground or B+
 
Generator 'F' terminal circuit is open, shorted to ground or B+
 
ECM has failed
 

Trouble Code: P0628



Fuel Pump Enable Circuit High Voltage

Possible Causes:



Short to voltage on the enable circuit
 
Fuel Pump Control Module (FECM)
 
ECM has failed
 

Trouble Code: P0629



Control Module Fuel Injector Control Performance

Possible Causes:



Module not properly programmed
 
ECM has failed
 

Trouble Code: P062F



Throttle Actuator Control (TAC) Command Performance

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body has failed
 
ECM has failed
 

Trouble Code: P0642



5-Volt Reference 1 Circuit High Voltage

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to FTP. CMP IMTV or TP sensor circuit is shorted to (B+)
 
Component failure
 
ECM has failed
 

Trouble Code: P0643



Air Conditioning Clutch Relay Control Circuit Malfunction

Possible Causes:



A/C relay control circuit is open, shorted to ground or to power
 
A/C relay power circuit is open (test the A/C CRUISE mini fuse)
 
A/C relay is damaged or has failed
 
ECM has failed
 

Trouble Code: P0650



5-Volt Reference 2 Circuit

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to APP. CKP, and CMP brake booster vacuum sensor circuit is shorted to (B+)
 
ECM has failed
 

Trouble Code: P0652



5-Volt Reference 2 Circuit High Voltage

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to APP TP or CKP sensor circuit is shorted to (B+)
 
Component failure
 
ECM has failed
 

Trouble Code: P0653



Intake Manifold Tuning (IMT) Valve Performance.

Possible Causes:



IMT low reference circuit for an open/high resistance
 
IMT 5-volt reference circuit for a short to ground or an open/high resistance
 
IMT 5-volt reference circuit for a short to voltage
 
IMT signal circuit for an open/high resistance
 
IMT signal circuit for a short to ground or an open/high resistance
 
IMT signal circuit for a short to voltage
 
IMT has failed
 
ECM has failed
 

Trouble Code: P065E



Intake Manifold Tuning (IMT) Valve Solenoid Control Circuit Low Voltage.

Possible Causes:



IMT ignition circuit for a short to ground or an open/high resistance.
 
IMT control circuit for a short to ground
 
IMT control circuit for a short to voltage or an open/high resistance
 
IMT component failure
 
ECM has failed
 

Trouble Code: P0661



Intake Manifold Tuning (IMT) Valve Solenoid Control Circuit High Voltage.

Possible Causes:



IMT ignition circuit for a short to ground or an open/high resistance.
 
IMT control circuit for a short to ground
 
IMT control circuit for a short to voltage or an open/high resistance
 
IMT component failure
 
ECM has failed
 

Trouble Code: P0662



Engine Controls Ignition Relay Control Circuit

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0686



Engine Controls Ignition Relay Control Circuit High Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0687



Engine Controls Relay Feedback Circuit Low Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0689



Engine Controls Ignition Relay De-energized Too Late

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P068B



Engine Controls Relay Feedback Circuit High Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P06A6



Transmission Control Module (TCM) Requested MIL Illumination

Possible Causes:



MIL control circuit is shorted to ground
 
Check the TCM for any trouble codes in memory that are responsible for the request to turn on the MIL
 
TCM has failed
 

Trouble Code: P0700



Clutch Switch Circuit Malfunction (M49/MM6)

Possible Causes:



Clutch switch circuit is open, shorted to ground or to power
 
Clutch switch power circuit is open (test the ENG IGN fuse)
 
Clutch switch is out of adjustment, damaged or has failed
 
ECM has failed
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158°F (70°C). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test RPM (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (RPM) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

Trouble Code: P1362



ICM Control Circuit High Input

Possible Causes:



IC timing signal is shorted to system power
 
IC timing control circuit and IC timing signal circuits are shorted
 
IC module is damaged or it has failed
 
ECM has failed
 

Trouble Code: P1380



Misfire Detected, Rough Road Data Not Available

Possible Causes:



Use the Freeze Frame/Failure Records data to help find the cause on an intermittent fault. If the code cannot be duplicated, the data in the Freeze Frame/Failure Records can determine how many miles since the code set. The Fail Counter and Pass Counter can also help determine how many ignition cycles the diagnostic reported a pass or a fail. Operate the vehicle within the Freeze Frame conditions (i.e., load, engine and vehicle speed, temperature etc.). This will isolate when the code set.
 
Service the ABS before diagnosing a misfire because an actual engine misfire may or may not exist. Also, an actual engine misfire may have occurred during an ABS malfunction.
 
Determine if the vehicle was driven on a rough road, and the ABS could not detect this due to a malfunction. The ECM may interpret variations in crankshaft speed caused by the rough road as a misfire without an actual engine misfire present.
 
Refer to Diagnostic System Check for Antilock Brake System
 
Refer to Diagnostic System Check for the Engine Controls
 

Trouble Code: P1381



Misfire Detected - No Communication with Brake Control Module

Possible Causes:



If any ABS DTCs are set, diagnose those first
 
ABS module
 

Trouble Code: P1400



Cold Start Emission Reduction Control System

Possible Causes:



Air intake system for Damage, restriction, or modification
 
Dirty or deteriorating air filter element
 
Crankcase ventilation system for correct operation
 
Vacuum leak and other un-metered air downstream of the Mass Air Flow (MAF) sensor
 
Intake manifold leak
 
Damaged, restricted, modified or enhanced exhaust system
 
Exhaust leaks
 

Trouble Code: P1516



TAC Module Throttle Actuator Position Performance

Possible Causes:



TAC motor CKT 1 or CKT 2 is open, shorted to ground or B+
 
Throttle actuator motor CKT 1 is shorted to CKT 2
 
Throttle actuator motor control module has failed
 
TSB 03-04-06-032 contains a repair procedure for this code
 

Trouble Code: P1585



Cruise Control Inhibit Output Circuit Malfunction

Possible Causes:



Cruise control inhibit circuit is shorted to system voltage
 
Cruise control inhibit circuit is open or shorted to ground
 
Cruise control module power circuit is open (test CR CNT fuse)
 
Cruise control module is damaged or has failed
 
ECM has failed
 

Trouble Code: P1682



Ignition 1 Switch Circuit 2

Possible Causes:



Powertrain relay controlled output circuit for a short to voltage
 
Powertrain relay coil voltage supply circuit for a short to ground or an open/high resistance.
 
Powertrain relay switch voltage supply circuit for an open/high resistance.
 
Ignition 1 relay controlled output circuit for a short to ground or open/high resistance
 
Powertrain relay
 
ECM has failed
 

Trouble Code: P2088



Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage

Possible Causes:



Ignition circuit for a short to ground or an open/high resistance
 
Control circuit for a short to voltage or an open/high resistance
 
Control circuit for a short to ground
 
CMP actuator solenoid
 
Faulty ECM
 

Trouble Code: P2089



Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage

Possible Causes:



Ignition circuit for a short to ground or an open/high resistance
 
Control circuit for a short to voltage or an open/high resistance
 
Control circuit for a short to ground
 
CMP actuator solenoid
 
Faulty ECM
 

Trouble Code: P2091



Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage (Bank 1)

Possible Causes:



Ignition circuit for a short to ground or an open/high resistance
 
Control circuit for a short to voltage or an open/high resistance
 
Control circuit for a short to ground
 
CMP actuator solenoid
 
Faulty ECM
 

Trouble Code: P2096



Post Catalyst Fuel Trim System Low Limit

Possible Causes:



Malfunctioning fuel injectors
 
Low fuel system pressure
 
Fuel that is contaminated
 
Missing, loose, or leaking exhaust components from the HO2S forward
 
Vacuum leaks
 
Ethanol concentration greater than 15 percent
 
Incorrect PCV system operation
 

Trouble Code: P2100



Throttle Actuator Control (TAC) Motor Control Circuit

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body malfuntion
 
ECM has failed
 

Trouble Code: P2101



Throttle Closed Position Performance

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body malfuntion
 
ECM has failed
 

Trouble Code: P2101



Control Module Throttle Actuator Position Performance

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body malfuntion
 
ECM has failed
 

Trouble Code: P2108



Throttle Actuator Control (TAC) Module Performance

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body malfuntion
 
ECM has failed
 

Trouble Code: P2119



Throttle Closed Position Performance

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body malfuntion
 
ECM has failed
 

Trouble Code: P2120



Accelerator Pedal Position Sensor 1 Signal Performance

Possible Causes:



APP sensor connector is damaged, open or shorted
 
APP1 sensor signal circuit is open or shorted to ground
 
APP1 sensor signal circuit is shorted to APP sensor 2 circuit
 
APP1 sensor signal circuit is open or shorted to VREF (5v)
 
APP sensor is damaged or it has failed
 
TAC module is damaged or it has failed
 

Trouble Code: P2122



Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

Possible Causes:



Low reference circuit of the APP sensor for a short to voltage, or an open/high resistance.
 
5-volt reference circuit for a short to ground or open/high resistance.
 
Faulty APP Sensor
 
ECM has failed
 

Trouble Code: P2123



Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

Possible Causes:



Low reference circuit of the APP sensor for a short to voltage, or an open/high resistance.
 
5-volt reference circuit for a short to ground or open/high resistance.
 
Faulty APP Sensor
 
ECM has failed
 

 
label.common.footer.alt.autozoneLogo