Continental 2000-2002

Overhaul

Print

These vehicles use several different types of joints. Engine size, transaxle type, whether the joint is an inboard or outboard joint, even which side of the vehicle is being serviced could make a difference in joint type. Be sure to properly identify the joint before attempting joint or boot replacement. Look for identification numbers at the large end of the boots and/or on the end of the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint (T.J.) and the Double Offset Joint (D.O.J.).


NOTE
Do not disassemble a Birfield joint. Service with a new joint or clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should be checked prior to and after boot service. This is so the boot will not be installed either too loose or too tight, which could cause early wear and cracking, allowing the grease to get out and water and dirt in, leading to early joint failure.


NOTE
The driveshaft joints use special grease; do not add any grease other than that supplied with the kit.

Double Offset Joint



The Double Offset Joint (D.O.J.) is bigger than other joints and, in these applications, is normally used as an inboard joint.

  1. Remove the halfshaft from the vehicle.
  2.  
  3. Side cutter pliers can be used to cut the metal retaining bands. Remove the boot from the joint outer race.
  4.  
  5. Locate and remove the large circlip at the base of the joint. Remove the outer race (the body of the joint).
  6.  
  7. Remove the small snapring and take off the inner race, cage and balls as an assembly. Clean the inner race, cage and balls without disassembling.
  8.  
  9. If the boot is to be reused, wipe the grease from the splines and wrap the splines in vinyl tape before sliding the boot from the shaft.
  10.  
  11. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is to be replaced, remove the boot retainer rings and slide the boot down and off of the shaft at this time.
  12.  

To install:

  1. Be sure to tape the shaft splines before installing the boots. Fill the inside of the boot with the specified grease. Often the grease supplied in the replacement parts kit is meant to be divided in half, with half being used to lubricate the joint and half being used inside the boot.
  2.  
  3. Install the cage onto the halfshaft so the small diameter side of the cage is installed first. With a brass drift pin, tap lightly and evenly around the inner race to install the race until it comes into contact with the rib of the shaft. Apply the specified grease to the inner race and cage and fit them together. Insert the balls into the cage.
  4.  
  5. Install the outer race (the body of the joint) after filling with the specified grease. The outer race should be filled with this grease.
  6.  
  7. Tighten the boot bands securely. Make sure the distance between the boot bands is correct.
  8.  
  9. Install the halfshaft to the vehicle.
  10.  

Except Double Offset Joint



  1. Disconnect the negative battery cable. Remove the halfshaft.
  2.  
  3. Use side cutter pliers to remove the metal retaining bands from the boot(s) that will be removed. Slide the boot from the T.J. case.
  4.  
  5. Remove the snapring and the tripod joint spider assembly from the halfshaft. Do not disassemble the spider and use care in handling.
  6.  
  7. If the boot is be reused, wrap vinyl tape around the spline part of the shaft so the boot(s) will not be damaged when removed. Remove the dynamic damper, if used, and the boots from the shaft.
  8.  

To install:

  1. Double check that the correct replacement parts are being installed. Wrap vinyl tape around the splines to protect the boot and install the boots and damper, if used, in the correct order.
  2.  
  3. Install the joint spider assembly to the shaft and install the snapring.
  4.  
  5. Fill the inside of the boot with the specified grease. Often the grease supplied in the replacement parts kit is meant to be divided in half, with half being used to lubricate the joint and half being used inside the boot. Keep grease off the rubber part of the dynamic damper (if used).
  6.  
  7. Secure the boot bands with the halfshaft in a horizontal position. Make sure distance between boot bands is correct.
  8.  
  9. Install the halfshaft to the vehicle and reconnect the negative battery cable.
  10.  



Click image to see an enlarged view

Fig. Check the CV-boot for wear



Click image to see an enlarged view

Fig. Removing the outer band from the CV-boot



Click image to see an enlarged view

Fig. Removing the inner band from the CV-boot



Click image to see an enlarged view

Fig. Removing the CV-boot from the joint housing



Click image to see an enlarged view

Fig. Clean the CV-joint housing prior to removing boot



Click image to see an enlarged view

Fig. Removing the CV-joint housing assembly



Click image to see an enlarged view

Fig. Removing the CV-joint



Click image to see an enlarged view

Fig. Inspecting the CV-joint housing



Click image to see an enlarged view

Fig. Removing the CV-joint outer snapring



Click image to see an enlarged view

Fig. Checking the CV-joint snapring for wear



Click image to see an enlarged view

Fig. CV-joint snapring (typical)



Click image to see an enlarged view

Fig. Removing the CV-joint assembly



Click image to see an enlarged view

Fig. Removing the CV-joint inner snapring



Click image to see an enlarged view

Fig. Installing the CV-joint assembly (typical)

Inner CV-Joint



The inner CV-joint is serviced with the halfshaft as an assembly. The inner CV-joint boot can be serviced by removing the outer CV-joint.

Outer CV-Joint



  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Place the halfshaft in a vise.
  4.  
  5. Remove the CV-joint boot clamps and slide the boot away from the joint.
  6.  
  7. Drive the CV-joint off the halfshaft with a brass drift and a hammer.

    Click image to see an enlarged view

    Fig. Removing the outer CV-joint

  8.  

To install:

  1. Replace the snapring.
  2.  
  3. Fill the CV-joint with fresh grease and slide the joint onto the halfshaft.
  4.  
  5. Use new clamps and install the CV-joint boot.
  6.  

 
label.common.footer.alt.autozoneLogo