Corolla 2006-2007

Exterior Lighting

Print

Back-up, Brake, Marker, Signal, & Tail Lights



Removal & Installation
Tail Lights
  1. Using a clip remover, remove the 2 clips and disconnect the luggage compartment trim cover.
  2.  
  3. Disconnect the wiring and remove the 3 nuts to remove the tail light assembly.
  4.  
  5. Installation is the reverse of removal.

    Click image to see an enlarged view

    Fig. Removing clips to remove the luggage compartment trim

  6.  

Assembly

Specific to:

Toyota Corolla 2006-2008

  1. Using a clip remover, remove the 2 clips and disconnect the luggage compartment trim cover LH.

    Click image to see an enlarged view

    Fig. Removing luggage compartment trim

  2.  
  3. Disconnect the connector and remove the 3 nuts

    Click image to see an enlarged view

    Fig. Disconnecting electrical connector

  4.  
  5. Pull out the rear combination light assembly LH to the back of the vehicle, and remove.
  6.  

To Install:

  1. Installation is the reverse of removal.
  2.  

Bulb

Specific to:

Toyota Corolla 2006-2008



Click image to see an enlarged view

Fig. Removing tail light cover panel



Click image to see an enlarged view

Fig. Removing tail light cover panel



Click image to see an enlarged view

Fig. Removing tail light/side marker/stop bulb



Click image to see an enlarged view

Fig. Installing tail light/side marker/stop bulb

Headlights



Removal & Installation
  1. Remove the radiator grille.

    Click image to see an enlarged view

    Fig. Remove the radiator grille



    Click image to see an enlarged view

    Fig. To remove the front bumper cover

  2.  
  3. To remove the front bumper cover, remove the 6 screws and 2 clips, then disengage the hook.
  4.  
  5. Remove the 3 bolts, remove the headlight assembly and disconnect the wiring.

    Click image to see an enlarged view

    Fig. Remove the headlight assembly-2003-2006 Corolla

  6.  

To install:

  1. If the headlight is undamaged, installation is the reverse of removal.
  2.  
  3. If the screw tabs are damaged, there are replacement parts available. Cut off the remains of the old tab and install a new tab using the screws supplied with the part.

    Click image to see an enlarged view

    Fig. If the tab is damaged, cut it off



    Click image to see an enlarged view

    Fig. Installing the upper repair tab



    Click image to see an enlarged view

    Fig. Installing the side repair tab

  4.  

Assembly

Specific to:

Toyota Corolla 2006-2008

  1. Remove the grille assembly 2 bolts and clip.
  2.  
  3. Using a screwdriver, disengage the 3 claws and remove the radiator grille.
  4.  
  5. Remove grill assembly

    Click image to see an enlarged view

    Fig. Removing grille assembly

  6.  
  7. Remove front bumper cover.
  8.  
  9. Remove the 2 screws and 2 clips.
  10.  
  11. Disengage the hook, and remove the bumper cover.
  12.  
  13. Disconnect the fog light connectors, if necessary.

    Click image to see an enlarged view

    Fig. Removing bumper cover

  14.  
  15. Remove 3 headlight assembly bolts.
  16.  
  17. Pull out the headlight assembly LH forward, then disconnect the bracket of body side.
  18.  
  19. Release the claws and disconnect the connectors as shown in the illustration, and remove the headlight assembly LH.

    Click image to see an enlarged view

    Fig. Removing headlight assembly



    Click image to see an enlarged view

    Fig. Removing headlight assembly claw

  20.  

To Install:

  1. Installation is the reverse of removal.
  2.  

Bulb

Specific to:

Toyota Corolla 2006-2008



Click image to see an enlarged view

Fig. Removing air cleaner duct



Click image to see an enlarged view

Fig. Removing bulbs by turning counterclockwise



Click image to see an enlarged view

Fig. Unplugging connector



Click image to see an enlarged view

Fig. Installing new bulb

 
label.common.footer.alt.autozoneLogo