Corvette 2005-2008

6.2L V8 VIN W Auto 4

Print

Trouble Code: P0606



Control Module Performance

Possible Causes:



Check the voltage and ground inputs to the ECM for a, short, open or high resistance
 
ECM has failed
 

Trouble Code: P0607



Vehicle Speed Output Circuit Malfunction

Possible Causes:



VSS output signal circuit is open, shorted to ground or to power
 
VSS output signal problem related to the Instrument Cluster or the Electronic Suspension Control Module (internal problem)
 
ECM has failed
 

Trouble Code: P060D



Control Module Vehicle Options Incorrect

Possible Causes:



ECM is not properly programmed
 
ECM has failed
 

Trouble Code: P062F



Throttle Actuator Control (TAC) Command Performance

Possible Causes:



Throttle blade that is not in the rest position
 
Throttle valve that is binding open or closed
 
Throttle valve that opens or closes without spring pressure
 
Throttle body has failed
 
ECM has failed
 

Trouble Code: P0641



5-Volt Reference 1 Circuit Low Voltage

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to FTP. CMP IMTV or TP sensor circuit is shorted to (B+)
 
Component failure
 
ECM has failed
 

Trouble Code: P0642



5-Volt Reference 1 Circuit High Voltage

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to FTP. CMP IMTV or TP sensor circuit is shorted to (B+)
 
Component failure
 
ECM has failed
 

Trouble Code: P0643



Air Conditioning Clutch Relay Control Circuit Malfunction

Possible Causes:



A/C relay control circuit is open, shorted to ground or to power
 
A/C relay power circuit is open (test the A/C CRUISE mini fuse)
 
A/C relay is damaged or has failed
 
ECM has failed
 

Trouble Code: P0650



5-Volt Reference 2 Circuit

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to APP. CKP, and CMP brake booster vacuum sensor circuit is shorted to (B+)
 
ECM has failed
 

Trouble Code: P0685



Engine Controls Ignition Relay Control Circuit Low Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0689



Engine Controls Ignition Relay Feedback Circuit Low Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0690



Engine Controls Ignition Relay Feedback Circuit High Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P069E



Fuel Pump Control Module Requested MIL Illumination

Possible Causes:



Fuel line pressure sensor, 5v VREF circuit shorted to ground or an open/high resistance
 
Fuel line pressure sensor, 5v VREF circuit for a shorted to voltage
 
Fuel line pressure sensor, low reference circuit for an open/high resistance
 
FECM has failed
 

Trouble Code: P06A6



Transmission Control Module (TCM) Requested MIL Illumination

Possible Causes:



MIL control circuit is shorted to ground
 
Check the TCM for any trouble codes in memory that are responsible for the request to turn on the MIL
 
TCM has failed
 

Trouble Code: P0700



Clutch Switch Circuit Malfunction (M49/MM6)

Possible Causes:



Clutch switch circuit is open, shorted to ground or to power
 
Clutch switch power circuit is open (test the ENG IGN fuse)
 
Clutch switch is out of adjustment, damaged or has failed
 
ECM has failed
 

Trouble Code: P1111



IAT Sensor Circuit Intermittent High Input

Possible Causes:



IAT sensor signal circuit is open (intermittent fault)
 
IAT sensor ground circuit is open (intermittent fault)
 
IAT sensor is damaged (an intermittent "open" condition)
 
ECM has failed
 

Trouble Code: P1112



IAT Sensor Circuit Intermittent Low Input

Possible Causes:



IAT sensor signal circuit is shorted to ground (intermittent fault)
 
IAT sensor is damaged (an intermittent "shorted" condition)
 
ECM has failed
 

Trouble Code: P1114



ECT Sensor Circuit Intermittent Low Input

Possible Causes:



ECT sensor signal circuit shorted to ground (intermittent fault)
 
ECT sensor has failed (possible intermittent shorted condition)
 
ECM has failed
 

Trouble Code: P1133



HO2S Insufficient Switching (Bank 1 Sensor 1)

Possible Causes:



HO2S low reference circuit for an open/high resistance
 
HO2S signal circuit for a short to ground
 
HO2S signal circuit for a short to voltage
 
HO2S signal circuit for an open/high resistance
 
HO2S has failed
 
ECM has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
ECM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
ECM has failed
 

Trouble Code: P1153



HO2S-21 (Bank 2 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
ECM has failed
 

Trouble Code: P1154



HO2S-21 (Bank 2 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
ECM has failed
 

Trouble Code: P1174



Fuel Trim Cylinder Balance (Bank 1)

Possible Causes:



Vacuum hoses for splits, kinks, and improper connections.
 
Crankcase ventilation system for improper operation
 
Air induction system for modified, damaged, leaking, or restricted components.
 
Restricted, damaged, leaking, or modified exhaust system from the catalytic converter forward
 
Fuel injectors for improper operation
 
Ignition system for improper operation
 

Trouble Code: P1175



Fuel Trim Cylinder Balance (Bank 2)

Possible Causes:



Vacuum hoses for splits, kinks, and improper connections.
 
Crankcase ventilation system for improper operation
 
Air induction system for modified, damaged, leaking, or restricted components.
 
Restricted, damaged, leaking, or modified exhaust system from the catalytic converter forward
 
Fuel injectors for improper operation
 
Ignition system for improper operation
 

Trouble Code: P1220



TP Sensor 2 Circuit Malfunction

Possible Causes:



TP2 sensor signal circuit is open, shorted to ground or to power
 
TP2 sensor VREF circuit is open or shorted to ground
 
TP2 sensor VREF circuit is shorted to system power (B+)
 
TP2 sensor ground circuit has a high resistance condition
 
TP2 sensor is damaged or has failed
 

Trouble Code: P1221



TP Sensor 1-2 Signal Correlation

Possible Causes:



TP1, 2 sensor signal circuit has a high resistance condition
 
TP1, 2 sensor VREF circuit has a high resistance condition
 
TP1, 2 sensor ground circuit has a high resistance condition
 
TP1, 2 sensor is damaged or has failed
 
TAC controller or the throttle body is damaged or has failed
 
TSB 02-06-04-005 contains a repair procedure for this code
 

Trouble Code: P1255



Fuel Pump Control Module Driver Overtemperature

Possible Causes:



Dirty build up on FECM housing
 
FECM has failed
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158°F (70°C). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test RPM (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (RPM) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

Trouble Code: P1362



ICM Control Circuit High Input

Possible Causes:



IC timing signal is shorted to system power
 
IC timing control circuit and IC timing signal circuits are shorted
 
IC module is damaged or it has failed
 
ECM has failed
 

Trouble Code: P1380



Misfire Detected, Rough Road Data Not Available

Possible Causes:



Use the Freeze Frame/Failure Records data to help find the cause on an intermittent fault. If the code cannot be duplicated, the data in the Freeze Frame/Failure Records can determine how many miles since the code set. The Fail Counter and Pass Counter can also help determine how many ignition cycles the diagnostic reported a pass or a fail. Operate the vehicle within the Freeze Frame conditions (i.e., load, engine and vehicle speed, temperature etc.). This will isolate when the code set.
 
Service the ABS before diagnosing a misfire because an actual engine misfire may or may not exist. Also, an actual engine misfire may have occurred during an ABS malfunction.
 
Determine if the vehicle was driven on a rough road, and the ABS could not detect this due to a malfunction. The ECM may interpret variations in crankshaft speed caused by the rough road as a misfire without an actual engine misfire present.
 
Refer to Diagnostic System Check for Antilock Brake System
 
Refer to Diagnostic System Check for the Engine Controls
 

Trouble Code: P1381



Misfire Detected - No Communication with Brake Control Module

Possible Causes:



If any ABS DTCs are set, diagnose those first
 
ABS module
 

Trouble Code: P1400



Cold Start Emission Reduction Control System

Possible Causes:



Air intake system for Damage, restriction, or modification
 
Dirty or deteriorating air filter element
 
Crankcase ventilation system for correct operation
 
Vacuum leak and other un-metered air downstream of the Mass Air Flow (MAF) sensor
 
Intake manifold leak
 
Damaged, restricted, modified or enhanced exhaust system
 
Exhaust leaks
 

Trouble Code: P1516



TAC Module Throttle Actuator Position Performance

Possible Causes:



TAC motor CKT 1 or CKT 2 is open, shorted to ground or B+
 
Throttle actuator motor CKT 1 is shorted to CKT 2
 
Throttle actuator motor control module has failed
 
TSB 03-04-06-032 contains a repair procedure for this code
 

Trouble Code: P1517



Throttle Actuator Control Module Performance

Possible Causes:



Test the charging system output (low voltage can set this code)
 
Inspect the TAC module connectors for signs of water intrusion. If water intrusion occurs, multiple codes may set without any circuit or component conditions present.
 
When the TAC module detects a fault condition, several TAC related codes set because there are redundant tests running.
 
TAC module has failed
 

Trouble Code: P1585



Cruise Control Inhibit Output Circuit Malfunction

Possible Causes:



Cruise control inhibit circuit is shorted to system voltage
 
Cruise control inhibit circuit is open or shorted to ground
 
Cruise control module power circuit is open (test CR CNT fuse)
 
Cruise control module is damaged or has failed
 
ECM has failed
 

Trouble Code: P1682



Ignition 1 Switch Circuit 2

Possible Causes:



Powertrain relay controlled output circuit for a short to voltage
 
Powertrain relay coil voltage supply circuit for a short to ground or an open/high resistance.
 
Powertrain relay switch voltage supply circuit for an open/high resistance.
 
Ignition 1 relay controlled output circuit for a short to ground or open/high resistance
 
Powertrain relay
 
ECM has failed
 

Trouble Code: P2120



Accelerator Pedal Position Sensor 1 Signal Performance

Possible Causes:



APP sensor connector is damaged, open or shorted
 
APP1 sensor signal circuit is open or shorted to ground
 
APP1 sensor signal circuit is shorted to APP sensor 2 circuit
 
APP1 sensor signal circuit is open or shorted to VREF (5v)
 
APP sensor is damaged or it has failed
 
TAC module is damaged or it has failed
 

Trouble Code: P2122



Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

Possible Causes:



Low reference circuit of the APP sensor for a short to voltage, or an open/high resistance.
 
5-volt reference circuit for a short to ground or open/high resistance.
 
Faulty APP Sensor
 
ECM has failed
 

Trouble Code: P2123



Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

Possible Causes:



Low reference circuit of the APP sensor for a short to voltage, or an open/high resistance.
 
5-volt reference circuit for a short to ground or open/high resistance.
 
Faulty APP Sensor
 
ECM has failed
 

Trouble Code: P2125



Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

Possible Causes:



Low reference circuit of the APP sensor for a short to voltage, or an open/high resistance.
 
5-volt reference circuit for a short to ground or open/high resistance.
 
Faulty APP Sensor
 
ECM has failed
 

 
label.common.footer.alt.autozoneLogo