Corvette 2005-2008

Brake Pads

Print

Removal & Installation



With J56 Brake System
  1. Inspect the fluid level in the brake master cylinder reservoir.
    1. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding.
    2.  
    3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
    4.  

  2.  
  3. Raise and suitably support the vehicle
  4.  
  5. Remove the tire and wheel assembly.
  6.  
  7. Remove the disc brake pad pins.
  8.  
  9. Using a brake pad spreader tool, compress the brake caliper pistons into the caliper bores.
  10.  
  11. Remove the pads from the housing.
  12.  

To install:

  1. Install the leading disc brake pads with the wear sensors on the trailing edge of the brake pad during forward wheel rotation, if equipped.
  2.  
  3. Hand install the disc brake pad pins while gently rocking the disc brake pads. The pins should require little effort to install.
    1. Repeat previous 2 steps to install the center and trailing pads.
    2.  

  4.  
  5. Tighten brake pad pins to 30 ft. lbs.(40 Nm).
  6.  
  7. Install the tire and wheel assembly.
  8.  
  9. Lower the vehicle.
  10.  
  11. With the engine OFF:
    1. Gradually apply the brake pedal to approximately 2/3 of its travel distance.
    2.  
    3. Slowly release the brake pedal.
    4.  
    5. Wait 15 seconds, then repeat steps 11-12 until a firm brake pedal apply is obtained. This will properly seat the brake caliper pistons and brake pads.
    6.  

  12.  
  13. Fill the brake master cylinder reservoir to the proper level.
  14.  
  15. Burnish the pads and rotors.

    Click image to see an enlarged view

    Fig. Front Disc Brake Pads Replacement (J56)

  16.  

Without J56 Brake System
  1. Inspect the fluid level in the brake master cylinder reservoir.
    1. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding.
    2.  
    3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding.
    4.  

  2.  
  3. Raise and suitably support the vehicle
  4.  
  5. Remove the tire and wheel assembly.
  6.  
  7. Hand tighten a wheel lug nut to a wheel stud to secure the rotor to the hub.
  8.  
  9. Install a large C-clamp over the body of the brake caliper with the C-clamp ends against the rear of the caliper body and against the outboard brake pad.
  10.  
  11. Tighten the C-clamp evenly until the caliper pistons are compressed into the caliper bores enough to allow the caliper to slide past the brake rotor.
  12.  
  13. Remove the C-clamp from the caliper.
  14.  
  15. Remove the upper brake caliper guide pin bolt.
    NOTE
    Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  16.  
  17. Pivot the brake caliper body downward and secure the caliper out of the way with heavy mechanic's wire or equivalent. Ensure that there is no tension on the hydraulic brake flexible hose.
    CAUTION
    Do NOT disconnect the hydraulic brake flexible hose from the caliper.

  18.  
  19. Remove the brake pads from the caliper bracket.
  20.  
  21. Remove and inspect the brake pad retainers from the caliper bracket.
  22.  

To install:

  1. Inspect the caliper slide boots for cuts, tears, or deterioration. If damaged, replace the slides and the boots.
  2.  
  3. Install the brake pad retainers to the caliper bracket.
  4.  
  5. Install the brake pads to the caliper bracket. The brake pad wear sensor, mounted on the inboard brake pad, must be positioned so that it is in the leading bottom position during forward rotation of the brake rotor.
  6.  
  7. Pivot the brake caliper upward, over the brake pads and into the caliper bracket.
  8.  
  9. Install the upper brake caliper guide pin bolt.
  10.  
  11. Tighten the brake caliper guide pin bolt to 23 ft. lbs.(31 Nm).
  12.  
  13. Install the tire and wheel assembly.
  14.  
  15. Lower the vehicle.
  16.  
  17. With the engine OFF:
    1. Gradually apply the brake pedal to approximately 2/3 of its travel distance.
    2.  
    3. Slowly release the brake pedal.
    4.  
    5. Wait 15 seconds, then repeat steps 11-12 until a firm brake pedal apply is obtained. This will properly seat the brake caliper pistons and brake pads.
    6.  

  18.  
  19. Fill the brake master cylinder reservoir to the proper level.
  20.  
  21. Burnish the pads and rotors.

    Click image to see an enlarged view

    Fig. Front Disc Brake Pads Replacement without (J56)

  22.  

 
label.common.footer.alt.autozoneLogo