Dakota 2006-2007

Stabilizer Bar (Sway Bar) & Links

Print

Removal & Installation



2-Wheel Drive
Bar
  1. Raise and support the vehicle.
  2.  
  3. Remove the upper link nut, retainer and grommet from each link.
  4.  
  5. Remove the stabilizer bar retainer bolts and remove the retainers and stabilizer bar from the vehicle.
  6.  
  7. Remove the bushings from the stabilizer bar.
    NOTE
    If bushings are to be reused, do not cut the old bushings off the stabilizer bar; use a mixture of soapy water to aid in sliding the bushings off the bar.

  8.  

To install:

  1. Install the bushings on the stabilizer bar using a mixture of soapy water or equivalent in order to slide the bushing over the bar with ease.
    WARNING
    Do not cut the new bushing for installation.

  2.  
  3. Install the stabilizer bar on the frame and install the retainers and the bolts.
  4.  
  5. Tighten the bolts to 45 ft. lbs. (60 Nm).
    NOTE
    Ensure the bar is centered with equal spacing on both sides.

  6.  
  7. Install the upper link grommet, retainer and nut and tighten to 27 ft. lbs. (37 Nm).
  8.  
  9. Remove support and lower vehicle.
  10.  

Links
  1. Raise and support the vehicle.
  2.  
  3. Remove the lower nut.
  4.  
  5. Remove the upper nut, retainers and grommets from the stabilizer bar.
  6.  
  7. Remove the stabilizer link from the vehicle.

    Click image to see an enlarged view

    Fig. 2WD stabilizer components: link (1), retainer (2), stabilizer bar (3), lower control arm (4), and lower nut (5)

  8.  

To install:

  1. Install the stabilizer link to the vehicle.
  2.  
  3. Install the retainers, grommets and upper nut to the stabilizer bar and tighten to 23 Nm (17 ft. lbs.).
  4.  
  5. Install the lower nut and tighten to 102 Nm (75 ft. lbs.).
  6.  
  7. Remove the support and lower the vehicle.
  8.  

4-Wheel Drive
Bar

NOTE
To service the stabilizer bar the vehicle must be on a drive on hoist. The vehicle suspension must be at curb height for stabilizer bar installation.

  1. Remove the stabilizer bar retainer bolts from the lower suspension arms and remove the retainers.
  2.  
  3. Remove the stabilizer bar retainer nuts, bolts and retainers from the frame crossmember and remove the bar.
  4.  
  5. If necessary, remove the bushings from the stabilizer bar.
    NOTE
    If bushings are to be reused, do not cut the old bushings off the stabilizer bar; use a mixture of soapy water to aid in sliding the bushings off the bar.



    Click image to see an enlarged view

    Fig. 4WD stabilizer components: lower control arm (1), nut (2), stabilizer bar (3) and retainers (4)

  6.  

To install:


NOTE
To service the stabilizer bar the vehicle must be on a drive on hoist. The vehicle suspension must be at curb height for stabilizer bar installation.

  1. If removed, install the bushings on the stabilizer bar using a mixture of soapy water or equivalent in order to slide the bushing over the bar with ease.
    WARNING
    Do not cut the new bushing for installation.

  2.  
  3. Position the stabilizer bar on the frame crossmember brackets and install the retainers and nuts and bolts finger-tight.
    NOTE
    Ensure the bar is centered with equal spacing on both sides.

  4.  
  5. Install the stabilizer bar to the lower suspension arm.
  6.  
  7. Install the retainers and bolts to the lower suspension arm and tighten to 34 Nm (25 ft. lbs.).
  8.  
  9. Tighten the frame retainer nuts to 190 Nm (140 ft. lbs.).
  10.  
  11. Tighten the frame retainer bolts to 108 Nm (80 ft. lbs.).
  12.  

Links

Control links are not utilized on 4WD models; the stabilizer end is mounted directly to the lower control arm.

 
label.common.footer.alt.autozoneLogo