Log In
Search suggestions

    My Vehicles

    Add a Vehicle

    Find a Store

    Select Store

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIVETHANKS

    See Details

    Edge, MKX 2007

    Removal & Installation

    Print

    Air Inlet Door Model Actuator




    NOTE
    It is not required to install the new air inlet door linkage parts included in the air inlet mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.

    1. To remove the air inlet mode door actuator and linkage, perform the following:
      1. Disconnect the glove compartment damper from the glove compartment.
      2.  
      3. Remove the glove compartment.
      4.  
      5. Remove the 3 air inlet mode door actuator screws.
      6.  
      7. Disconnect the air inlet mode door actuator electrical connector.
      8.  
      9. Remove the air inlet mode door actuator.
      10.  
      11. Manually operate and inspect the air inlet mode door and air inlet mode door linkage for incorrect placement or damage.
      12.  

    2.  
    3. To remove the air inlet mode door linkage only, perform the following:
      1. Remove the air inlet mode door intermediate lever screw.
      2.  
      3. Remove the air inlet mode door intermediate lever.
      4.  
      5. Working through the air inlet duct grille opening, depress the clip and detach the air inlet mode door lever from the air inlet mode door.
        NOTE
        The air inlet mode door must be fully seated in the correct position during installation. If the air inlet mode door is not fully seated, excessive noise will result when the climate control system is operated.



        Click image to see an enlarged view

        Fig. Working through the air inlet duct grille opening, depress the clip and detach the air inlet mode door lever from the air inlet mode door

      6.  

    4.  
    5. Installation is the reverse of the removal procedure

      Click image to see an enlarged view

      Fig. Exploded view of the air inlet mode door actuator



      Click image to see an enlarged view

      Fig. Exploded view of the air inlet mode door actuator linkage

    6.  

    Defrost/Panel/Floor Door Mode Actuator




    NOTE
    The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.


    NOTE
    It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.

    1. To remove the mode door actuator and linkage, perform the following:
      1. Remove the 3 defrost/panel/floor mode door actuator screws.
      2.  
      3. Disconnect the defrost/panel/floor mode door actuator electrical connector.
      4.  
      5. Remove the defrost/panel/floor mode door actuator.
      6.  
      7. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.

        Click image to see an enlarged view

        Fig. View of the Defrost/Panel/Floor Door Mode Actuator

      8.  

    2.  
    3. To remove the mode door actuator linkage only, refer to the illustration and perform the following:
      1. 1. Depress the tab and remove the panel door lever.
      2.  
      3. 2. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      4.  
      5. 3. Pull straight outward to remove the floor/defrost door lever.
        NOTE
        When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.



        Click image to see an enlarged view

        Fig. Steps for removing the mode door actuator linkage only, refer to text

      6.  

    4.  
    5. Installation is the reverse of the removal procedure
    6.  

    Temperature Blend Door Actuator



    Left Side

    NOTE
    It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.

    1. To remove the LH temperature blend door actuator and linkage, perform the following:
      1. Remove the 2 lower steering column opening cover bolts.
      2.  
      3. Detach the lower steering column opening cover.
      4.  
      5. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
      6.  
      7. Position the instrument panel wire harness away from the LH temperature blend door actuator.
      8.  
      9. Remove the 3 LH temperature blend door actuator screws.
      10.  
      11. Disconnect the LH temperature blend door actuator electrical connector.
      12.  
      13. Remove the LH temperature blend door actuator.
      14.  
      15. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.

        Click image to see an enlarged view

        Fig. Exploded view of the left side temperature blend door actuator and linkage

      16.  

    2.  
    3. To remove the LH temperature blend door linkage only, perform the following:
      1. Detach the 2 retaining tabs and remove the LH temperature blend door linkage.
      2.  

    4.  
    5. Installation is the reverse of the removal procedure.
    6.  

    Right Side-Dual Zone, EATC

    NOTE
    It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.

    1. To remove the RH temperature blend door actuator and linkage, perform the following:
      1. Disconnect the glove compartment damper from the glove compartment.
      2.  
      3. Remove the glove compartment.
      4.  
      5. Remove the RH lower instrument panel insulator.
      6.  
      7. Remove the RH lower floor console trim panel.
      8.  
      9. Remove the 3 RH temperature blend door actuator screws.
      10.  
      11. Disconnect the RH temperature blend door actuator electrical connector.
      12.  
      13. Remove the RH temperature blend door actuator.
      14.  
      15. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.

        Click image to see an enlarged view

        Fig. Exploded view of the right side temperature blend door actuator and linkage-vehicles with dual zone EATC

      16.  

    2.  
    3. To remove the RH temperature blend door actuator linkage only, perform the following:
      1. Detach the 2 retaining tabs and remove the RH temperature blend door linkage.
      2.  

    4.  
    5. Installation is the reverse of the removal procedure.
    6.  

     
    AutoZone Logo