Log In
Search suggestions

    My Vehicles

    1976 Mercedes Benz 300D 3.0L Diesel 5cyl

    My Store

    1720 S RIDGEWOOD A
    (386) 427-1210

    OPEN 'til 8:00 PM today

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Honda CRV/Odyssey 1995-2000 Repair Information

    Evaporative Emission Controls

    Print

    OPERATION



    Changes in atmospheric temperature cause fuel tanks to breathe, that is, the air within the tank expands and contracts with outside temperature changes. If an unsealed system was used, when the temperature rises, air would escape through the tank vent tube or the vent in the tank cap. The air which escapes contains gasoline vapors.

    The Evaporative Emission Control System provides a sealed fuel system with the capability to store and condense fuel vapors. When the fuel evaporates in the fuel tank, the vapor passes through the EVAP emission valve, through vent hoses or tubes to a carbon filled evaporative canister. When the engine is operating the vapors are drawn into the intake manifold and burned during combustion.

    A sealed, maintenance free evaporative canister is used. The canister is filled with granules of an activated carbon mixture. Fuel vapors entering the canister are absorbed by the charcoal granules. A vent cap is located on the top of the canister to provide fresh air to the canister when it is being purged. The vent cap opens to provide fresh air into the canister, which circulates through the charcoal, releasing trapped vapors and carrying them to the engine to be burned.

    Fuel tank pressure vents fuel vapors into the canister. They are held in the canister until they can be drawn into the intake manifold. The canister purge valve allows the canister to be purged at a pre-determined time and engine operating conditions.

    Vacuum to the canister is controlled by the canister purge valve. The valve is operated by the PCM. The PCM regulates the valve by switching the ground circuit on and off based on engine operating conditions. When energized, the valve prevents vacuum from reaching the canister. When not energized the valve allows vacuum to purge the vapors from the canister.

    During warm up and for a specified time during hot starts, the PCM energizes the valve-preventing vacuum from reaching the canister. The EVAP purge control solenoid begins to operate when the engine coolant temperature reaches a predetermined operating temperature.

    Once the proper coolant temperature is achieved, the PCM controls the ground circuit to the valve. When the PCM opens the ground, this allows vacuum to flow through the canister and vapors are purged from the canister into the throttle body. During certain idle conditions, the PCM may energize the purge valve to control fuel mixture calibrations.

    The fuel tank is sealed with a pressure-vacuum relief filler cap. The relief valve in the cap is a safety feature, preventing excessive pressure or vacuum in the fuel tank. If the cap is malfunctioning, and needs to be replaced, ensure that the replacement is the identical cap to ensure correct system operation.

    The following components are part of and affect the operation of the EVAP (Evaporative Emission) Control system:



    Fuel Tank
     
    Fuel Fill Cap
     
    Evap Two Way Valve
     
    Evap Control Canister
     
    Evap Three Way Valve
     
    Fuel Tank Pressure Sensor
     
    Powertrain (PCM) Control Module
     
    Evap Purge Control Solenoid Valve
     
    Evap Control Canister Vent Shut Valve
     

    See Figure 1

    Click image to see an enlarged view

    Fig. Fig. 1: Schematic of the EVAP Control System-1998-99 CRV shown

    COMPONENT TESTING



    The Evaporative Emission (EVAP) Controls are monitored by the Powertrain Control Module (PCM) and if found to be malfunctioning the PCM records the problem in the fault memory as a Diagnostic Trouble Code (DTC). If the problem persists or compromises the vehicle's emissions, the Malfunction Indicator Light (MIL) could be activated.

    Evaporative Emissions (EVAP) Control Canister

    This canister is used as a storage facility for fuel vapors that have escaped from components such as the fuel tank. This canister prevents these vapors from entering the atmosphere.

    Generally, the only testing done to the canister is a visual inspection. Look the canister over and replace it with a new one if there is any evidence of cracks or other damage.

    See Figure 2

    Click image to see an enlarged view

    Fig. Fig. 2: EVAP control canister-1997 CRV shown

    Evaporative Hoses and Tubes

    Inspect all system hoses and tubes for signs of damage or cracks. Any damage or leakage must be repaired.

    Evaporative Emissions Purge Control Solenoid Valve

    The evaporative emissions control solenoid valve is located at between the canister and the intake manifold.

    1. Disconnect the vacuum hose from the valve.
    2.  
    3. Connect a vacuum pump to the vacuum hose.
    4.  
    5. Turn the ignition switch ON .
    6.  

    See Figure 3

    Click image to see an enlarged view

    Fig. Fig. 3: Installed view of the EVAP bypass solenoid valve and the EVAP two-way valve

    1. Apply vacuum to the hose.
    2.  
    3. If the valve holds vacuum, the valve is OK.
    4.  
    5. If the valve does not hold vacuum:
      1. Turn the ignition switch OFF .
      2.  
      3. Detach the electrical connector from the valve.
      4.  
      5. Check for continuity between the red/yellow wire and ground. If continuity is present, replace the valve. If no continuity is present, check for an open circuit in the red/yellow wire between the valve and the PCM.
      6.  

    6.  
    7. When finished testing, attach all disconnected hoses, connectors, and wires.
    8.  

    REMOVAL & INSTALLATION Evaporative Emissions Canister



    1. Raise and support the vehicle.
    2.  
    3. Remove the bolts retaining the Evaporative Emissions (EVAP) canister and bracket assembly.
    4.  
    5. Label and disconnect the vapor hoses from the canister.
    6.  
    7. Remove the canister from the bracket.
    8.  
    9. Installation is the reverse of the removal procedure.
    10.  

    Evaporative Emissions Control Shut Valve

    1. Disconnect the vacuum hose from the EVAP shut valve.
    2.  
    3. Remove the fasteners that hold the EVAP shut valve to the canister.
    4.  
    5. Remove the EVAP control shut valve from the canister.
    6.  

    To install:
    1. Install the EVAP control shunt valve and fasteners.
    2.  
    3. Connect all vacuum hoses.
    4.  

    See Figure 4

    Click image to see an enlarged view

    Fig. Fig. 4: The Control Canister Vent Shut Valve is mounted on top of the EVAP Canister on 1998-99 CRV Models

    Canister Purge Valve (Two-Way Valve)

    1. Raise and support the vehicle.
    2.  
    3. Detach the electrical harness from the valve.
    4.  

    See Figure 5

    Click image to see an enlarged view

    Fig. Fig. 5: Exploded view of the EVAP two-way valve

    1. Disconnect the fuel vapor hoses and remove the valve.
    2.  
    3. Installation is the reverse of the removal procedure.
    4.  

     
    AutoZone Logo