Envoy, Rainer, Trailblazer 2006-2007

4.2L L6 VIN S Auto 5

Print

Trouble Code: P0563



System Voltage High

Possible Causes:



Observe the driver information center (DIC) messaging that would indicate the electrical system requires service.
 
Inspect for loose or damaged terminals at the generator.
 
Inspect for loose or worn generator drive belt.
 
Use the scan tool in order to inspect all other modules for voltage related DTCs.
 
Running the engine with a battery charger attached may cause DTC P0563 to set.
 
Inspect the charging circuit for high resistance.
 
Inspect the vehicle battery for open or sulfated cells.
 

Trouble Code: P0564



Cruise Control Multi-Function Switch Circuit

Possible Causes:



Ensure that the set/coast and the resume/accel switch are not stuck in the engaged position.
 
Repair all other DTCs and emissions related symptoms before performing this diagnostic.
 

Trouble Code: P0567



Cruise Control Resume Switch Circuit

Possible Causes:



Ensure that the resume/accel switch is not stuck or sticking in the engaged position.
 
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0567



Cruise Control Resume Switch Circuit

Possible Causes:



Ensure that the resume/accel switch is not stuck or sticking in the pressed position.
 

Trouble Code: P0568



Cruise Control Set Switch Circuit

Possible Causes:



Ensure that the set/coast switch is not stuck in the engaged position.
 
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0568



Cruise Control Set Switch Circuit

Possible Causes:



Ensure that the set/coast switch is not stuck or sticking in the pressed position.
 

Trouble Code: P0601



Control Module Read Only Memory (ROM)

Trouble Code: P0602



Control Module Not Programmed

Trouble Code: P0603



Control Module Long Term Memory Reset

Trouble Code: P0604



Control Module Random Access Memory (RAM)

Trouble Code: P0605



Control Module Programming Read Only Memory (ROM)

Trouble Code: P0606



Control Module Internal Performance

Trouble Code: P0607



Control Module Performance

Trouble Code: P0608



Vehicle Speed Output Circuit

Trouble Code: P060D



Control Module Accelerator Pedal Position (APP) System Performance

Trouble Code: P060E



Control Module Throttle Position (TP) System Performance

Trouble Code: P0621



Generator L-Terminal Circuit

Trouble Code: P0622



Generator F-Terminal Circuit

Possible Causes:



On vehicles equipped with a sense circuit connected to the voltage regulator. This circuit must have voltage for the charging system to operate properly. This circuit is used as a reference to control system voltage. All circuits must be tested at the generator before replacing any components. refer to system schematic to confirm if the vehicle being serviced uses the sense circuit as part of the charging system.
 

Trouble Code: P0622



Generator F-Terminal Circuit

Trouble Code: P062F



Long Term Memory Performance

Trouble Code: P0641



5-Volt Reference 1 Circuit

Trouble Code: P0645



A/C Clutch Relay Control Circuit

Trouble Code: P0650



Malfunction Indicator Lamp (MIL) Control Circuit

Trouble Code: P0651



5-Volt Reference 2 Circuit

Trouble Code: P0651



5-Volt Reference 2 Circuit

Possible Causes:



It may be possible to locate the fault by disconnecting one component at a time from the 5-volt reference circuit while viewing the 5-Volt Reference circuit parameter on the scan tool. The scan tool parameter would change from Fault to OK when the source of the fault is disconnected. If all 5-volt reference components have been disconnected and a Fault is still indicated, the fault may exist in the wiring harness.
 

Trouble Code: P0654



Engine Speed Output Circuit

Trouble Code: P0685



Engine Controls Ignition Relay Control Circuit

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0689



Engine Controls Ignition Relay Feedback Circuit Low Voltage

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0690



Engine Controls Ignition Relay Feedback Circuit High Voltage

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0700



Transmission Control Module (TCM) Requested MIL Illumination

Possible Causes:



DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.
 

Trouble Code: P0705



Transmission Range (TR) Switch Circuit

Trouble Code: P0711



Transmission Fluid Temperature (TFT) Sensor Performance

Trouble Code: P0711



Transmission Fluid Temperature (TFT) Sensor Performance

Possible Causes:



The DIC, if equipped, will display TRANSMISSION HOT - IDLE ENGINE when the transmission fluid temperature reaches 132°C (270°F).
 
Ask the customer about possible overloading, exceeding the trailer towing limit, or towing in overdrive.
 

Trouble Code: P0712



Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage

Possible Causes:



The scan tool displays the transmission fluid temperature in degrees. After the transmission is operating, the fluid temperature should rise steadily to a normal operating temperature, then stabilize.
 
Verify the customer's driving habits, trailer towing, etc. Trailer towing should occur in D3.
 

Trouble Code: P0713



Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Trouble Code: P0716



Input Speed Sensor Performance

Possible Causes:



Inspect the connectors at the TCM, the AT ISS, and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections .
 
Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents .
 
Road test the vehicle while monitoring the Transmission ISS parameter on the scan tool. The Transmission ISS parameter should vary with engine speed changes and not abruptly drop out.
 
Inspect for an open or shorted AT ISS wire.
 
Inspect for a disconnected AT ISS connector.
 
Inspect for a faulty AT ISS.
 

Trouble Code: P0717



Input Speed Sensor Circuit Low Voltage

Possible Causes:



Inspect the connectors at the TCM, the AT ISS, and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections .
 
Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents .
 
Road test the vehicle while monitoring the Transmission ISS parameter on the scan tool. The Transmission ISS parameter should vary with engine speed changes and not abruptly drop out.
 
Inspect for an open or shorted AT ISS wire.
 
Inspect for a disconnected AT ISS connector.
 
Inspect for a faulty AT ISS.
 

Trouble Code: P0719



Brake Switch Circuit Low Voltage

Possible Causes:



Inspect for ABS DTCs. A faulty ABS condition may contribute to setting DTC P0719.
 

Trouble Code: P0719



TCC Brake Switch Circuit Low Voltage

Possible Causes:



Inspect for ABS DTCs. A faulty ABS condition may contribute to setting DTC P0719.
 
It may be necessary to also clear this DTC from the engine control module (ECM).
 

Trouble Code: P071A



Transmission Tow Mode Switch Circuit

Possible Causes:



If the electrical circuit tests are OK and the shift pattern is not occurring, there may be a mechanical/hydraulic condition that prevents operation. Refer to Symptoms - Automatic Transmission .
 

 
label.common.footer.alt.autozoneLogo